475259
65
Zoom out
Zoom in
Previous page
1/110
Next page
5. NetCommand IR Control (838 Series) 65
For assistance call 1(800) 332-2119
Placement
The NetCommand system uses emitters connected
to the
IR
NetCommand Output
jack to control other
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
IR emitter cables are available for purchase from
Mitsubishi. Request either part number 242D483020
(two-ended cable) or part number 299P254020 (four-
ended cable).
1.
Connect the plug end of the IR emitter cable to the
IRNetCommand Output
jack on the TV back panel.
2.
When the New Device Found screen displays,
highlight
IRNetCommand Output.
The New Device Found screen displays when you
connect the IR emitter.
3.
Highlight EXIT and press
ENTER
.
4.
Position the emitter end with the emitter bulb facing
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
5.
Secure the emitter ends in place using double-
sided tape.
6.
Place any unused ends behind the devices to
prevent stray signals from reaching the IR sensors.
1
2
3
HDMI
AUDIO
OUTPUT
Pb Pr
INPUT 2
INPUT 1
DIGITAL
AUDIO
OUTPUT
DVI/PC
(480i / 480p / 720p / 1080i)
LR INPUT
AUDIO
Y/ VIDEO
Pb Pr
Y/ VIDEO
3D
GLASSES
EMITTER
ANT
AUDIO
LR
LR
LAN
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
CENTER
INPUT
SUB
WOOFER
OUTPUT
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
IR-NetCommand
Output/EXTERNAL
CONTROLLER INPUT
TV main panel
D I G I TA L
SU R R O U N D
S
CH
A/V Receiver
Other A/V Device
Connecting IRNetCommand Output
In front of a
single average-
sized device
On top of a single
tall device
In front, shared
by two average-
sized devices
IR sensor
IR sensor
IR sensor
IR sensor
In front of a single
average-sized device
On top of a single tall
device
In front, shared by two
average-sized devices
IR sensor
IR sensor
IR sensor
IR sensor
IR sensor
In front of a single
average-sized device
On top of a single
tall device
In front, shared by
two average-sized
devices
IR sensor
IR sensor
IR sensor
IR sensor
IR sensor
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
If You are Unable to Locate
a Device’s IR Sensor
• The IR sensor is usually behind the plastic window
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
• If you cannot see the sensor and the device’s
Owner’s Guide does not specify the location, do
the following using the device’s remote control.
1. Starting at one end of the plastic window, hold
the device’s remote control about one-half
inch from the front of the device and press the
POWER
key.
2. If the device does not respond, move the
remote control one inch toward the center and
try again. Repeat until the device responds.
3. Repeat the previous steps starting at the other
end of the window. The sensor is between
these two points.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
IR Emitters
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65838 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info