475272

Mitsubishi WD-65837 Manual

47
Zoom out
Zoom in
Previous page
1/88
Next page
5. NetCommand IR Control (837 Series) 47
To perform this procedure, you need:
The remote controls for both the TV and the •
device you want to control.
An IR emitter cable available from Mitsubishi•
.
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 52.
Connect and position the IR emitters for the
1.
devices you wish to control. See “IR Emitter Place-
ment” on the opposite page.
Set the
2.
TV’s remote control to
TV
mode and power
on the TV.
Open the NetCommand
3.
Learn screen as follows:
If working from the • New Device Found screen
after the device is first detected, highlight
NetCommand and press
ENTER
to open the
Learn screen for the device.
If performing NetCommand setup at any time •
after the device has been recognized through
Auto Input Sensing:
a. Press
ACTIVITY.
b. Highlight the desired input icon and press
ENTER
to switch to that input.
c. Press
MENU
, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
The first function highlighted in the
4.
Learn screen
is always Power On. Aim the TV’s remote control
at the TV and press
ENTER
to begin learning for that
function.
When the
5.
Power On
text starts flashing, aim the
device’s
remote control at the TV and hold the
POWER
key until a check mark appears next to Power On.
If the text stops flashing before the check mark •
appears, repeat the previous step.
To remove the key from NetCommand control, •
press the
CANCEL
key while the key name is
highlighted.
Press the
6.
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
Note: Device keys in the far right column will be asso-
ciated with the remote control’s
MORE
key when
“learned.” See the table on page 49.
If the device has a separate
7.
POWER OFF
key, press
on the TV’s remote to highlight Power Off.
Repeat the earlier steps to “learn” the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
Press
8.
BACK
to finish NetCommand “learning” for the
current device.
From the New Device Found screen, highlight
NetCommand and press ENTER to open the Learn
screen.
Initial NetCommand Setup
Inputs > Learn screen
Key names marked with a
check have been “learned.”
Device-specific keys in the
rightmost column can be accessed
with the MORE key after “learning.”
Adding or Removing Device Keys from
NetCommand Control
Switch the TV to the device. Press
1.
ACTIVITY
, high-
light the device’s icon, and press
ENTER
.
Open the
2.
Inputs menu and highlight the Learn icon.
When the
3.
Learn screen displays:
To add keys: • Continue as described earlier
under “Initial NetCommand Setup” on this
page.
To delete keys:• Highlight the name of the key
you wish to delete and press
CANCEL
on the
TV‘s remote control to clear the check mark.
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65837 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65837 in the language / languages: English as an attachment in your email.

The manual is 5,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info