475260
85
Zoom out
Zoom in
Previous page
1/110
Next page
Appendices 85
For assistance call 1(800) 332-2119
4.
If prompted for a name,
highlight a name for the
device and press
ENTER
to
add a check. The device
itself may later override the
name assigned.
5.
Highlight On and press
ENTER
to add a check.
7.
Highlight EXIT and press
ENTER
to close the New
Device Found screen.
Note: At any time after completing Auto Input Sens-
ing, you can set the TV’s HDMI control on or off
in the Inputs > HDMI Control menu.
8.
838 Series. To supplement HDMI control with
NetCommand IR control, see page 64.
Many new HDMI devices have a feature called Con-
sumer Electronics Control (CEC) or HDMI Control.
HDMI Control allows one device, such as the TV, to
control other devices, such as an A/V receiver or disc
player. Use of CEC is optional.
Each manufacturer chooses which CEC functions to
support so it is difficult to predict which devices and
features are compatible with Mitsubishi’s HDMI Control.
You may find that CEC functions for a specific device are
limited.
To use HDMI Control, you must enable it in both
the TV and the device.
• In the TV. Enable HDMI control from the New
Device Found screen or from the Inputs > HDMI
Control menu.
• I
n the Device. Most devices with HDMI CEC com-
patibility let you turn it on or off in the device menus,
where it is typically listed as “HDMI Control.
Enabling HDMI Control of CEC Devices
To ensure proper detection
• Power on HDMI devices before connecting them to
the TV.
• Connect and set up HDMI devices one at a time.
1.
Power on the device and allow it to complete the
power-on sequence (boot up). Stop any playback.
2.
Connect the device to one of the TV’s HDMI inputs.
3.
When the TV detects the connection, the New
Device Found screen will appear.
Note: See “If the New Device Found Screen Has No
HDMI Control Option” on this page if there is no
HDMI Control option.
New Device Found screen with HDMI Control option.
This screen displays only if the device’s HDMI Control is
enabled
.
Appendix C: HDMI Control of CEC Devices
If the New Device Found Screen
Has No HDMI Control Option
If the New Device Found screen shows no option for
HDMI Control, one of these conditions applies:
• HDMI Control is turned off in the menus of the
new device
Action:
a. Highlight EXIT and press
ENTER
to close the
New Device Found screen.
b. Display the device’s setup menus and enable
the devices CEC capabilities.
c. Wait for the TVs New Device Found screen
to appear again.
d. If the New Device Found screen does not
appear, power off the device. Power on the
device and wait for the New Device Found
screen to display with the HDMI Control
option.
• The HDMI cable cannot support CEC
Action:
Upgrade your HDMI cable to one that supports
CEC.
• The device does not have CEC compatibility
Action:
- Control the device with its own remote
control or program the TV’s remote control to
operate the device.
- 838 Series. Use the TV’s NetCommand IR
control (page 64).
85


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65738 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65738 in the language / languages: English as an attachment in your email.

The manual is 7,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info