475298
48
Zoom out
Zoom in
Previous page
1/84
Next page
48 6. NetCommand
IR Emitter Placement (NetCommand®)
An IR emitter cable is included with the TV.
TheNetCommandsystemusesemittersconnectedto
the
IR EMITTER
jacktocontrolotherdevicessuchas
DVDplayers,cableboxes,satellitereceivers,andVCRs.
1. ConnecttheplugendofthesuppliedIRemitter
cabletothe
IR EMITTER NetCommand®
jackonthe
TVbackpanel.
2. Runthecableforeachoftheemitterendsunder,
alongside,orovereachdevicetobecontrolledso
thattheemitterendisinfrontoftheareawherethe
remotecontrolsensorislocated.
3. Positiontheemitterendwiththeemitterbulbfacing
theremotecontrolsensor.Thebulbemitsinfrared
lightinacone-shapedpattern.Placethebulbfar
enoughfromthesensortoallowtheconepattern
toreachthesensor.
TheIRsensorisusuallybehindtheplasticwindow
ofthefrontdisplaypanel.Itissometimesvisible
withtheaidofaflashlightandisnormallyaround
orsquarecutoutbehindtheplastic.Ifyoucannot
seethesensorandthedevice’sOwner’sGuide
doesnotspecifythelocation,youcanfinditby
followingthesestepsusingthedevice’sremote
control:
a. Holdthedevice’sremoteaboutone-halfinch
fromthefrontofthedevice.Startingfromone
endofthedisplaywindowplastic,pressthe
POWER
button.
b. Ifthedevicedoesnotrespond,movethe
remotecontroloneinchtowardthecenterand
tryagain.
c. Repeatthisuntilthedeviceresponds.
d. Notethislocationandthenstartoverfromthe
otherendofthedisplaywindowplastic,repeat-
inguntilthedevicerespondsagain.
Theremotecontrolsensorissomewhere
betweenthesetwopositions.Thisisusually
enoughaccuracyforplacementoftheIRemit-
ters.
Withsomedevices,theemitterworksbetter
facingdownwardfromthetopofthedevice.
Experimenttofindwhatworksbest.
4. Securetheemitterendsinplaceusingdouble-
sidedtape.
5. Placeanyunusedendsbehindthedevicesto
preventstraysignalsfromreachingtheIRsensors.
INPUT 1
INPUT 2
L
(MONO) R
AUDIO
ANT 2/ AUX
ANT 1 / MAIN
DIGITAL
AUDIO
OUT
HDMI
1
2
Y
Pb
Pr
AVR
AUDIO
OUTPUT
S-VIDEO
VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
COMPONENT 1
COMPONENT 2
IR EMITTER
NetCommand
R
57#BDL1BOFM
%*(*5"-
463306/%
4
$)
"73FDFJWFS
0UIFS"7EFWJDF




Connecting IR Emitter NetCommand
*OGSPOUPGB
TJOHMFBWFSBHF
TJ[FEEFWJDF
0OUPQPGBTJOHMF
UBMMEFWJDF
*OGSPOUTIBSFE
CZUXPBWFSBHF
TJ[FEEFWJDFT
*3TFOTPS
*3TFOTPS
*3TFOTPS
*3TFOTPS
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65734 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65734 in the language / languages: English as an attachment in your email.

The manual is 3,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info