475317

Mitsubishi WD-65731 Manual

63
Zoom out
Zoom in
Previous page
1/108
Next page
Chapter 5. Operating Other Devices with the Remote Control 63
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Method 1: Code Entry
1. Movetheslideswitchatthetopoftheremotetothe
positionfortheproductyouwanttocontrol.Referto
thetablebelow.Onlyoneofeachdevicetypecanbe
controlledineachslide-switchposition.
Switch Position Affected Device
CABLE/SAT
CableBox
DTVReceiver
SatelliteReceiver
VCR
VCR
DVR
LaserDiscPlayer
DVDPlayer/Recorder
DVD
DVDPlayer/Recorder
DVR
LaserDiscPlayer
VCR
AUDIO
A/VReceiver
AudioAmplifier
CDPlayer*
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Releasethe
POWER
button.
4. Enterthefirstfive-digitcodelistedforyourequipment.
• The
POWER
buttonblinkstwicewhenyoustartto
enterthecodeandthenonceforeachadditional
keypress.
• The
POWER
buttonblinkstwicewhenyoufinish
enteringavalidcode.
• Movetheslideswitchtoanotherpositionifyou
needtostartoverorwishtoexitprogramming
mode.
5. Pointtheremotecontrolattheequipmentandpress
POWER
. Iftheproducthasnopoweron/offfunction,
pressadifferentkey,suchas (
PLAY
), (
STOP
),
VOL
,or
MUTE.
• Iftheequipmentresponds,theremotecontrolis
properlyprogrammedtooperatetheequipment.
• Iftheequipmentdoesnotrespond,repeatsteps
2–4withthenextfive-digitcodelistedforyour
equipment.
6. Onceyouhavefoundthecorrectcode,writeitinthe
spacebelowforfuturereference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Method 2: Code Search
Inthismethodofprogramming,youstepthroughthe
remotecontrol’sinternalcodelibrarytofindthecorrect
codeforyourA/Vproduct.
1. Movetheslideswitchatthetopoftheremotecontrol
tothecorrectpositionfortheproduct.Seethetable
under“Method1.”
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 1
4. Pressthenumber
1
,
2
,or
3
dependingontheslide-
switchpositionandthetablebelow.
Switch Position Number
CABLE/SAT
1
DVD, VCR
2
AUDIO
3
5. Press
CH
and
POWER
repeatedlyuntiltheproduct
respondsbypoweringonoroff.Youcanpress
CH
tomovebackwardthroughthecodelibraryifneeded.
NOTE: Iftheproducthasnopoweron/offfunction,check
foraresponseusingadifferentfunction.Press
(
PLAY
), (
STOP
),
VOL
,or
MUTE
andthenre-
peatedlypress
CH
/ tocheckforaresponse.
6. Whentheproductresponds,press
ENTER
tosetthe
code.
Code Verification
Todeterminethecodeprogrammedforanypositionof
theslideswitch:
1. Movetheslideswitchtothepositionyouwishto
verify.
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 0
4. Press
1
andcounttheblinksofthepowerbutton.
Writedownthenumberofblinksasthefirstdigitof
thecode.
5. Repeatstep4forthesecond,third,fourth,andfifth
digitsofthecode.
… 63 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-65731 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-65731 in the language / languages: English as an attachment in your email.

The manual is 8,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info