Manual Mitsubishi WD-62628 (page 49 of 124) (English)

475319

Zoom out

Zoom in

1/124

Chapter 3. NetCommand Setup and Editing 49

[Device] Screen

Figure 17

If you selected “None” for a device type during initial

setup, you can later add a device with this screen. This

screen also opens when you select the Change option in

the Edit NetCommand screen.

The sample screens here show the choices for adding a

VCR; similar screens will appear for any satellite receiver,

DVD player, or cable box.

Figure 17. [Device] screen

Choose ONE of these options:

• Selectarecognizedmanufacturer.Themodel

number optimized for NetCommand will display at

the bottom of the screen. If a number follows the

manufacturer’s name, (example: Mitsubishi 1), this

indicates additional models are optimized for that

manufacturer. For many device types, non-listed

models will operate in the same way as the listed

models and you can still use the pre-loaded setting.

After selecting Next>, the screens that follow are: the

Name Screen (Figure 20), Connection screen (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

• Select“Other,”thenhighlight“Learn”andpress

ENTER. This will allow you to have NetCommand

learn the remote control signals of this new device.

After selecting “Learn” and pressing ENTER, the

screens that follow are: [Device] Learn screen (Figure

18), [Device] Advanced Learn screen (Figure 19),

Name screen (Figure 20), Connection screen, (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

Edit NetCommand®: Add Devices, continued

• Select“Other”,skipLearnandselectNext>. This

will allow the device to appear and will allow

NetCommand to switch inputs to use this device.

However, NetCommand will not be able to control this

device. Later you may use the “Change” option in the

Setup menu to learn the remote control signals.

After selecting Next>, the screens that follow are: the

Name Screen (Figure 20), Connection screen (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

[Device] Learn Screen

Figure 18

Shown only if “Learn” was selected

1. Press ADJUST to select the check box for

each function to be learned.

2. Press ENTER and the function name will begin to

flash to confirm the ready-to-learn status.

3. Press the button on the device’s remote control that

corresponds to the selected function. A check mark

will appear and the function name will stop flashing.

This confirms the signal learned status.

4. To test the learned command, press the ENTER

button on the TV remote while the learned function

is still highlighted. The device should perform the

selected function. The device needs to be turned on

and the IR emitters properly placed for the test to be

successful (see page 32 for IR emitter placement).

5. Repeat for each function to be learned.

6. To erase a learned function, highlight the check box

for that function and press CANCEL.

7. When the function signals have been learned, press

ADJUST to select Next> and move to the [Device]

Advanced Learn screen.

NOTE: When learning the device’s remote control

signals, point the device’s remote control at the TV

screen.

Hint: If the device’s remote control uses a single button

for both Power On and Power Off, don’t learn the Power

Off function.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Mitsubishi WD-62628 Manual

Product: