475319
22
Zoom out
Zoom in
Previous page
1/124
Next page
22 Chapter 2. Connecting
Connecting External Devices and NetCommand® Setup
.PEFM
.73
.73
.PEFM
.73
.73
.PEFM
-JGFTUZMF ¥
.PEFM
"73
.PEFM
%53
.PEFM
73
.PEFM
43
.PEFM
749%
.PEFM
74959
.PEFM
349
.PEFM
453%&
.PEFM
397
.PEFM
397
%FWJDF"VEJP0VUQVUUP "73FDFJWFS*OQVUTCZ/BNF
7$3
7$3 7$3 7$3 7$3 7JEFP 7JEFP 7$3
7$35BQF
7$3%73 7JEFP 7JEFP 7$3 7$3
4BUFMMJUF3FDFJWFS "VY
$BCMF%#4 "69 $% 7JEFP 7JEFP %44 $% 4"5 7JEFP 57%#4 57%#4 %57-%
%7%1MBZFS
%7% %7% CVJMUJO %7%7%1 %7% 7JEFP %7% -%4"5 %7%-% 7JEFP 5"1&.% $% %7%
57.POJUPS0VUQVU
%JHJUBM"VEJP
57 57 57 57%#4 7JEFP 7JEFP 57 %7%57 57 7JEFP %7%-% %7%-% $#-4"5
$IBSU
.JUTVCJTIJ.JUTVCJTIJ#PTF%FOPO*OUFHSB,FOXPPE.BSBOU[1JPOFFS1JPOFFS3PUFM4POZ:BNBIB:BNBIB
AV
Receiver
TV
Device to be
connected
stereo and/or digital
audio cables
video and stereo
audio cables
stereo and/or digital audio cables
*3&NJUUFST
NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to
each device through IR emitters. Additionally, it can learn the remote control signals used by most audio video devices
not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video
(A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver
back panels match the NetCommand setup that is displayed on screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this
chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio
and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the
ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information
starting on page 45.
The following charts show which preset inputs you should use on the TV and A/V receiver.
Chart 1 shows the default TV inputs existing in NetCommand.
Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.
Chart 1
NetCommand Default Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service ANT-1
Antenna/Cable (digital/analog) ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
Cable box COMPONENT-1
VCR Input-1
Satellite Receiver (SAT) Input-2
Camcorder Input-3 (on front panel)
DVD Player COMPONENT-2
PC HDMI-2
After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for
connecting each device, custom name devices, add devices not included in the presets above or delete devices no
longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on device
setup.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-62628 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-62628 in the language / languages: English as an attachment in your email.

The manual is 7,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info