475277
78
Zoom out
Zoom in
Previous page
1/88
Next page
78 Appendices
Appendix E: Troubleshooting, continued
Sound
Symptom Remarks
2. The sound does not match the screen
picture.
The TVs “Listen to:” setting may be set to SAP
(analog program from
the ANT input)
.
3. The sound from my A/V receiver does
not match the screen picture (I should
hear the correct audio from my A/V
receiver).
Check that DIGITAL AUDIO OUTPUT and/or AVR AUDIO •
OUTPUT on TVs main panel is connected to the A/V receiver.
Without this connection, devices connected only to the TV (and
not the A/V receiver) can be heard only from the TV speakers.
Note that this includes the ANT input, a device (such as a
camcorder) connected to the convenience panel, and any other
device sending audio to the TV only.
If using a NetCommand-controlled A/V receiver, NetCommand •
may be selecting the wrong A/V receiver audio input. Check the
A/V receiver’s NetCommand setup in the Inputs > AVR menu.
4. Cannot select an audio-only device; it
does not appear in the Activity menu.
Plug an unused video plug into the
Y/VIDEO
jack to activate Auto
Input Sensing and make the audio device selectable in the Activity
menu.
.5. Sound is coming from the TV speakers
instead of the A/V receiver.
Disconnect headphones. Connect the TVs AUDIO OUT to the A/V
receiver and select AV Receiver from the New Device Found screen.
NetCommand IR Control (NetCommand-equipped models only)
Symptom Remarks
1. Cannot see the menu from the A/V Receiver. A/V Receiver Set Up for Audio-Only Switching•
The A/V Receiver is not connected to any video input of the
TV. To check the A/V Receiver menu, temporarily plug into
an unused input of the TV, such as Input 3. Exit the New
Device Found screen and select Input 3 from the Activity
menu. Press MENU on the A/V receiver’s remote control.
A/V Receiver Set Up for Audio and Video Switching over •
HDMI
Use the MENU key on the A/V receiver’s remote control.
A/V Receiver with • HDMI Control
Switch the remote control to AUDIO mode. Press the
MORE key and then 1 (Menu).
2. NetCommand unable to learn specific device
keys.
A/V Device does not use IR format for remote control •
signal. ITT and RF formats cannot be learned.
Room lighting may affect the signal. Have the remotes very •
close (6 inches or less) to the TV during Learning.
If learning a Mitsubishi remote control, make sure mode is •
not set to TV.
Some, but not all, device key functions can be learned by •
NetCommand. For example, POWER and PLAY may be
learned, but other functions may not.
The signal from the remote control may not be strong •
enough. Insert fresh batteries and try Learning again.
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-60737 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-60737 in the language / languages: English as an attachment in your email.

The manual is 5,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info