475285
27
Zoom out
Zoom in
Previous page
1/108
Next page
26
27
Connecting the IR Emitter NetCommand
®
IR EMITTER
NetCommand
R
DTV/
CABLE/
VHF/
UHF
ANT-1
MAIN
DVI
Analog Audio
L
R
TV back panel
(section detail)
D
I
G
I
T
A
L
S
U
R
R
O
U
N
D
S
C
H
A/V Receiver
Other A/V device
Other A/V device
1.
4.
3.
2.
3.
Figure 17. Connecting IR Emitter NetCommand
IR Emitter NetCommand®
Figure 17
A quadruple IR Emitter cable is included with the TV.
The emitters connected to these jacks are used by the
NetCommand system to control other devices such as
VCRs, DVD players, Cable boxes and Satellite receivers.
1. Connect the plug end of the supplied quadruple
IR Emitter Cable to one of the IR Output
NetCommand jacks on the TV back panel.
2. Run the cable for each of the emitter ends under,
along side or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This
bulb emits infrared light in a cone shaped pattern.
The bulb needs to be placed far enough from the
remote control sensor to allow the cone pattern to
include the sensor.
The remote control sensor is usually behind the
plastic window of the front display panel. It is
sometimes visible when you look through the display
plastic using a flashlight and is normally a round or
square cutout behind the plastic. If you cannot see
the sensor and the devices Owner’s Guide does
not specify the location, you can find it by using the
device’s remote control. Hold the remote about 1/2
inch from the front of the device. Starting from one
end of the display window plastic, press the POWER
button.
If the device does not respond, move the remote
control 1 inch toward the center and try again.
Repeat this until the device responds. Note this
location then start over from the other end of the
display window plastic, repeating until the device
responds again. The remote control sensor will be
somewhere between these two positions. This is
usually enough accuracy for the placement of the IR
emitters.
4. With some devices, the emitter will work better
facing downward from the top of the device.
Some experimentation may be needed.
5. The emitter end being used can be secured in
place using double stick tape.
If a single emitter end can be placed in a
position that will operate more than one device,
do not use a separate emitter end for the
additional device. A single device receiving
remote control signals from too many emitters
or remote controls may not respond at all.
IMPORTANT
6. If you are not going to
be using all emitter ends,
place the unused ends behind the devices so that
they cannot send signals to the remote control
sensors.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi WD-52725 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi WD-52725 in the language / languages: English as an attachment in your email.

The manual is 8,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info