32975
25
Zoom out
Zoom in
Previous page
1/64
Next page
25
25
TV
AUDIO
CABLE/DBS DVD
VCR
1
2
POWER
Code to enter:
To reset to default code, enter 000
DVD/LDP brand
Mitsubishi (DVD)
Mitsubishi (LDP)
Panasonic
Pioneer DVD (LDP)
Sony
Toshiba
003
016, 017
250
252 (016, 017)
254
253
If your
DVD
code is not
listed here,
please see
page 62
for a
complete
listing.
DVD/LDP Player Codes
3
Figure 4. Programming the remote to control your DVD/
LDP.
TV
AUDIO
CABLE/DBS DVD
VCR
1
2
POWER
Code to enter:
To reset to default code, enter 000
Audio brand
Mitsubishi A/V receiver
and/or CD player
Denon
Kenwood
JVC
Onkyo
Pioneer
Sony
Yamaha
Set M-VR1000 or M-VR800 to 015
Set M-VR900 or M-VR700 to 010
234, 235, 236
200, 208
232, 233
209, 214
205, 207
222
201, 208
If your
audio
code is not
listed here,
please see
page 62
for a
complete
listing.
A/V Receiver Codes
3
Figure 5. Programming the remote to control your A/V
receiver.
If the slide switch is set to TV when you
enter an A/V receiver code, VOLUME
and MUTE will control the A/V receiver
rather than the TV. To return volume
and mute control to the TV, set the slide
switch to TV, press and hold POWER
and enter 000.
Some manufacturers may change their
products, or they may use more than
one remote control system. If this is the
case, your remote control may not be
able to operate your VCR, DVD, cable
box, satellite receiver, or A/V receiver.
Part III: Setup
Programming the Remote Control: To Control Other A/V Products
After entering the correct codes for each
position of the remote control, use the slide
switch to select the product to control when
an operational button is pressed. If you
enter a code from the AUDIO chart while
the slide switch is set to TV, the volume
and mute functions change to match the A/V
receiver. This is useful when using an A/V
receiver with the TV all the time. In all
other cases, only one of the below devices
is allowed for each slide switch position.
TV position:
TV
A/V receiver (volume and mute only)
Cable/DBS position:
Cable box
Satellite receiver
VCR position:
VCR
DVD position:
DVD
LD Player
Audio position:
A/V receiver
Mitsubishi CD player [If you have a Mitsubishi A/V
receiver, the audio position may be used in conjunction with
select Mitsubishi CD players. Your audio position must be
programmed to either 010 or 011. Plug the CD player power
cord into a switched outlet on the back of your A/V receiver.
Pressing the POWER button will then turn on your A/V receiver,
in turn, turning on your CD player. On select CD players, the
transport controls (FF, Play, Rew, etc.) in the audio position will
operate the CD player.]
Programming the Remote Control: To Control Other A/V Products
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi VS70709 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi VS70709 in the language / languages: English as an attachment in your email.

The manual is 11,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info