549861
69
Zoom out
Zoom in
Previous page
1/80
Next page
EN-69
Troubleshooting
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be
sure to unplug the power plug, and then contact your dealer.
No image appears on the screen.
Problem Solution
Power can not be
turned on.
• Checkwhethertheindicatorsareonoroffandhowtheyarelightning.
POWER LAMP 1 LAMP 2 STATUS FILTER Solution
Off Off Off Off Off
• Connectthepowercordtotheprojector.
• Plugthepowercordintoawalloutlet.
Steady red
Off Off Off Off
• Ifanyobjectsareblockingtheintakeorexhaust
vents, remove them and carry out the following.
Unplug the power cord from the wall outlet.1.
Make sure that the projector has cooled off. 2.
Plug the power cord into a wall outlet.3.
Press the POWER button.4.
Off Off
Blinking
orange
Off
• Ifanyobjectsareblockingtheintakeorexhaust
vents, remove them.
• Don’texposetheexhaustventstohotairemitted
from a heating appliance.
• Checkwhetherthelterisdirtyornot.
Clean the filter. (See page 68.)
Blinking green* Off Off
• WaituntiltheLAMPindicatorsstopblinkinggreen
and then press the POWER button.
• Ifyouunplugthepowercordwhilethefanisrotating,the
lamp may not turn on about 2 minutes when you plug the
power cord next time.
•
The lamp can’t turn on again for 2 minutes after it goes out.
• PressthePOWERbuttonseveraltimes.
Steady red*
Off Off
• Replacethelightsourcelampindicatedbythe
illuminating indicator. (The time for replacing the light
source lamp has come.)
Blinking
red/green
Off Off
Off Off
• Attachthelampcover,ltercover,andcolorwheel
replacement cover.
Steady*
or
Blinking*
• Unplugthepowercordfromthewalloutletand
contact your dealer.
*: Status of either or both of the indicators.
No image appears on
the screen.
• PresstheBLANKbuttontocancelBLANK.
• Checkthatthelenscapisremoved.
• Itmaytakeabout2minutesforthelamptolightup.
• Thelampfailstolightuponrareoccasions.Insuchacase,waitforafewminutes
and then try again.
• Iftheprojectorwasturnedoffbeforethelampwascooleddownsufcientlylasttime,
the fan may start rotating and the POWER button may not work after the power cord
is plugged. After the fan stops rotating, press the POWER button to turn back on the
POWER indicator.
• SetSCARTINPUTintheFEATUREmenutoOFF.(Seepage37.)
• Checkthattheintakeventisclean.
• Checkthatthecablesconnectedtotheexternaldevicesarenotbroken.
•
When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension cable.
Power turns off. • Thisproblemmayoccurwhentheintakeventand/orexhaustventsareblocked.(In
such a case, the STATUS indicator brinks orange.)
Remove the objects blocking the intake vent and/or exhaust vents and then carry
out the following procedure.
1. Wait for the intake fan and/or exhaust fan to stop. (Wait until the STATUS indicator
goes out.)
2. Unplug the power cord from the wall outlet.
3. Wait about 10 minutes.
4. Plug the power cord into a wall outlet.
5. Press the POWER button.
• WhentheLAMPindicatorissteadyred,itisindicatingthatthelampshouldbe
replaced. Replace the lamp that is being indicated by the indicator.
• CheckthatAUTOPOWEROFFhasbeensettoOFF.
• Ifthelamphasdeteriorated,itmaygooutafterawhileitilluminates.
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi UD8850U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi UD8850U in the language / languages: English as an attachment in your email.

The manual is 11,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi UD8850U

Mitsubishi UD8850U Additional guide - English - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info