493636
14
Zoom out
Zoom in
Previous page
1/34
Next page
EN 14
Basic operation (continued)
VOLUME 15
Volume from the speaker
Press the VOLUME + or button to change the
volume from the speaker.
The volume control bar will appear on the screen.
The volume control bar will disappear about 10
seconds after the VOLUME button is released.
The VOLUME buttons dont function while the
menu selection bar or the menu is being
displayed.
When a high-level audio signal, such as a DVD
audio signal, is supplied to the AUDIO IN
terminal, the output from the speaker may be
distorted.
AV mute
The video and audio signals are temporarily muted
when the MUTE button is pressed. To cancel muting,
press the MUTE button again.
If MUTE MODE in the INSTALLATION menu is
set to IMAGE, the splash screen will appear when
the MUTE button is pressed.
You can alter the splash screen optionally. See
page 21.
When muting starts, the lamp mode becomes
LOW, darkening the display of IMAGE. This is
not a product malfunction.
Caution:
After using the projector, wait one minute for the
air outlet fans to stop. Then unplug the power
cord from the wall outlet.
The lamp cant be lit again for one minute after
turned off for safety purpose. It will take another
one minute for the STATUS indicator to go out. If
you want to turn on the projector again, wait until
the indicator goes out, and then press the POWER
button.
The air outlet fans rotate faster as the
temperature around the projector rises.
When the temperature around the projector rises
high, the sign TEMPERATURE!! blinks red on
the screen. If the temperature stays high, the
lamp will go out automatically.
Power-off
Use the following procedure to turn off the projector.
Do not turn off the projector by unplugging the power
cord while the lamp is on. Unplugging while the lamp
is on degrades the lamps performance and causes
failure in the projector.
11. Press the POWER button.
The message POWER OFF? YES : PRESS
AGAIN appears on the screen.
To cancel, press any button except the POWER
button. (Some buttons on the remote control
dont function for cancel.)
22. Press the POWER button within 10 seconds again.
The lamp will go out and the STATUS
indicator will start blinking.
Though the lamp goes out at this second press
of the POWER button, the air outlet fans
continue operating for one minute to cool down
the lamp and LCD panels. The STATUS
indicator will stop blinking.
33. Unplug the power cord.
The POWER indicator will go out.
If the power cord should be unplugged
accidentally while either the air inlet fan or the
air outlet fans are operating or the lamp is on,
allow the projector to cool down for 10 minutes
with the power off. To light the lamp again,
press the POWER button. If the lamp doesnt
light up immediately, repeat pressing the
POWER button two or three times. If it should
still fail to light up, replace the lamp.
Important:
When storing the projector in the provided
carrying case, the lens should face up.
AUTO POSITION button
When the image isnt projected in the right position
with COMPUTER selected as the input source, follow
the procedure below.
1. Project a bright image such as the Recycle Bin
window on the full screen.
2. If the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
If the image is still not in the right position,
adjust the image position using the SIGNAL
menu.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi SL4SU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi SL4SU in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info