549864
62
Zoom out
Zoom in
Previous page
1/76
Next page
EN-62
Replacing the lamp
This projector is equipped with 2 lamps to project
images. This lamp is a consumable. It may burn out
or its brightness may decrease during use. In such
cases, replace the lamp with a new one as soon as
possible. Be sure to replace the lamp with a new lamp
separately sold that is exclusive to this projector.
Contact your dealer for purchase of the lamp.
Spare lamp VLT-XD8000LP
Warning:
Be careful not to drop the lamp fi xing screws into
the inside of the projector. Don’t put a metal piece
or fl ammable object into the projector. Using the
projector with any foreign object present inside
may result in electric shock or fi re. When you can’t
remove the foreign object from the inside, contact
your dealer for removal.
Be sure to install the lamp securely. When the lamp
isn’t installed properly, it won’t illuminate. Improper
installation may also result in fi re.
Don’t shake the removed lamp or don’t lift it above
your face. You may be injured in your eye by fl ying
or falling glass fragments.
Don’t replace the lamp immediately after use
because the lamp cover is very hot. You may get
burned. Turn off the power using the POWER
button. After the lamp goes out, wait about 2
minutes until the intake and exhaust fans for
cooling the lamp stop rotating. Then turn off the
main power switch, unplug the power cord, and
wait at least 1 hour to allow the lamp to cool down
enough to the touch.
Do not touch the lamp directly. It may break and
cause injury or burn.
Interval of lamp replacement
The recommended interval of lamp replacement is
about 4000 hours
*1*2
of consecutive use. Such interval
differs depending on the operating environment
and may be shorter than 4000 hours
*1*2
. Decrease
in luminescence and/or color brightness indicates
that the lamp needs to be replaced. When the lamp
operation time exceeds 3000 hours
*1
, the indicator
will blink alternately between green and red (while the
lamp is lit; when the lamp is not lit, the indicator will
be lit red only) and the lamp replacement message
will appear on the screen for 1 minute everytime the
lamp is turned on. When the lamp has been used
for about 3800 hours
*1
, the replacement message
(LAMP REPLACEMENT) will appear on the screen for
1 minute every 20 hours
*1
thereafter. When the lamp
operation time exceeds 4000 hours
*1*2
, the projector
automatically shuts off.
*1: Duration when LAMP MODE of the INSTALLATION 1
menu is set to LOW. When it is set to STANDARD, this
duration will be shorted.
*2: When LAMP MODE is set to STANDARD, this duration
will be shorted to 2000 hours.
Caution:
Don’t remove the lamp for any purpose other than
replacement. Unnecessary removal of the lamp
may result in a breakdown.
This projector uses a high-pressure mercury lamp
as the light source. The high-pressure mercury
lamp may explode or fail to illuminate permanently
because of an impact, scratch, or deterioration
through use. The period of time until explosion or
permanent failure to illuminate varies considerably
from lamp to lamp, depending on operation
conditions. Therefore, the lamp may explode soon
after the start of use.
The possibility of explosion of the lamp increases if
you use it beyond its replacement period. When the
instruction of lamp replacement appears, replace it
with a new one immediately even if the lamp is still
lighting normally.
When the high-pressure mercury lamp explodes,
glass fragments will scatter inside or outside the
lamp box and the gas charged inside the lamp
will diffuse inside or outside the projector. The gas
inside the lamp contains mercury. Be careful not
to breathe it or avoid it from entering your eye or
mouth. If you should breathe it or if it should enter
your eye or mouth, see a doctor immediately.
In the event that the high-pressure mercury
lamp exploded, glass fragments may have been
scattered inside the projector. Ask your dealer to
replace the lamp and to inspect the inside of the
projector. When you clean or replace the lamp by
yourself, be sure to hold the handle of the lamp.
You may get injured by glass fragments.
When removing the lamp from the ceiling-mounted
projector, use the lamp replacement tray packed
with the projector or option lamp to prevent glass
fragments from scattering.
Be sure to use the lamp exclusive to this projector,
VLT-XD8000LP. Use of other lamps may cause a
failure of the projector.
Before replacing the lamp
1. Check which indicator (for LAMP 1 or LAMP 2) is
illuminating or blinking.
LAMP 2 indicator
LAMP 1 indicator
For the statuses of the indicators urging you to
replace the lamps, see page 71.
Replace the lamp indicated by the illuminating/
blinking indicator using the following procedure.
When both indicators are illuminating or blinking,
replace both lamps at the same time.
To replace the lamp:
1. Turn off the main power switch and unplug the
power cord.
2. Loosen two screws (a) that are securing the lamp
cover using a Philips screwdriver and remove the
lamp cover (b) from the projector.
(a)
(b)
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi LU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi LU in the language / languages: English as an attachment in your email.

The manual is 10,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi LU

Mitsubishi LU User Manual - English - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info