475237

Mitsubishi L75-A81 Laservue Manual

67
Zoom out
Zoom in
Previous page
1/100
Next page
Appendices 65
In the U.S. call 1(877) 675-2224 for assistance.
Programming the Remote Control
Press the side button on the remote control to
1.
change to the correct mode for the product you
want to control. Refer to the table below. Only
one of each device type can be controlled in each
mode.
Mode Available Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
Press and hold
2.
POWER
on the remote control for
several seconds until the mode indicator blinks
twice and goes off.
Release the
3.
POWER
key.
Enter the first five-digit code listed for your equip-
4.
ment.
The mode indicator blinks twice when you •
start to enter the code and then once for each
additional keypress.
The mode indicator blinks twice when you finish •
entering a valid code.
If you need to start over or wish to exit pro-•
gramming mode, temporarily change to a
different mode using the side button.
Point the remote control at the equipment and
5.
press
POWER
. If the product has no power on/off
function, press a different key, such as (
PLAY
),
(
STOP
),
VOLUME UP
, or
MUTE.
If the equipment responds, the remote control •
is properly programmed.
If the equipment does not respond, repeat •
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Mode
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
Set the mode to the one you wish to verify.
1.
Press and hold
2.
POWER
on the remote control for
several seconds until the
mode indicator
blinks twice
and goes off.
Press keys
3.
9 9 0
Press
4.
1
and count the blinks of the power key.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
5.
digits of the code.
Audio Lock: Universal A/V Receiver
Control
With Audio Lock enabled, the remote control operates
volume and mute on the A/V receiver in all modes set by
the side button. Activate Audio Lock if you always use
an A/V receiver with your TV and other A/V equipment.
Program
1.
AUDIO
mode for your A/V receiver as
described in “Programming the Remote Control” on
this page.
With the remote control in
2.
AUDIO
mode, hold
POWER
on the remote control for several seconds until the
mode indicator blinks twice and goes off.
Press keys
3.
9 9 3 ENTER
The mode indicator will blink twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Press and hold
1.
POWER
for several seconds until the
mode indicator blinks twice and goes off.
Press keys
2.
9 9 3 VOLUME UP
.
The mode indicator will blink four times to indicate
Audio Lock has cleared.
Appendix A: Programming the Remote Control, continued
… 67 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi L75-A81 Laservue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi L75-A81 Laservue in the language / languages: English as an attachment in your email.

The manual is 11,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info