31038
15
Zoom out
Zoom in
Previous page
1/80
Next page
13
3 You are now watching the VCR’s picture. To go back to viewing the picture
from the TV, press the TV’s INPUT button to go back to the previous ANTENNA
input position.
4 Later, you should turn the RF converter OFF by following instructions on page
61.
If your system includes a home theater receiver or an A/V receiver, refer to your
home theater receiver’s owner’s guide.
TV without Audio/Video Inputs
If your TV does not have separate audio/video inputs, then your VCR will need to
convert the VCR’s picture to channel 3 or 4. This is called the video channel. The
factory has already selected channel 3; however, if it is a broadcast channel in
your area, then you will need to change this to channel 4. To make this change:
set up
1 To choose channel 4: with VCR power OFF, turn the front panel jog dial disk
clockwise while holding down the SP/EP button on the front panel. Ant ch 4
will display on the front panel and the VCR will send signals on channel 4.
If needed, to return to channel 3: with the VCR turned OFF, turn the jog dial
counter-clockwise while holding down the SP/EP button on the front panel.
Ant ch 3 will display.
2 Turn the VCR on by pressing POWER.
operating
3 Check to see if the VCR light on the front panel display is lit. If it is not, press
VCR/TV on the remote control until the VCR light appears on the front panel.
This light must be on when you watch a video tape or use the VCR menus.
The VCR light will turn on automatically when you play a tape or use the VCR
menus when the RF converter is set to ON. See page 61.
4 Turn on the TV and change the TV to the video channel (3 or 4). You are now
watching the VCR’s picture.
To watch a channel that is different than the channel your VCR is recording, the
VCR light must be off. The VCR/TV button turns this light on and off.
Operating Your Remote Control
Installing the Batteries
1 To remove the back cover, press the ridged area gently, then push the cover in
the direction of the arrow and lift.
2 Load the batteries, making sure the polarities (+) and (–) are correct.
This is marked inside the battery compartment.
Next, you need to tell the remote control to operate the VCR, not the TV.
Operating the VCR with the Remote Control
The HS-HD2000U has two VCR remote control operational settings: VCR-A and
VCR-B. The HS-HD2000U is pre-set to VCR-A setting. See page 65 for informa-
tion about VCR operational setting.
1 Set the VCR/TV slide switch on the remote control to VCR position. This “tells”
the remote that you want to control the VCR.
Now your remote is ready to operate your HS-HD2000U. If the VCR does not
respond to the remote, please see page 65.
VCR/TV
POWER
JOG/CHANNEL
SP/EP
Playback
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HSHD2000U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HSHD2000U in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info