30512
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
Device Selection Menu
This menu allows you to:
• Select the device for viewing on the display monitor.
• Select display monitor speakers or A/V Receiver
speakers for the audio.
• Change a NetCommand® compatible A/V Receiver’s
inputs automatically.
• Power NetCommand devices on or off.
• Verify NetCommand recordings and peer-to-peer
connections.
• Cancel recordings or peer-to-peer connections.
• Display the menu for HAVi devices.
Transport Menu
This menu allows you to operate the transport functions of
NetCommand compatible IR controlled and IEEE 
recording and playback devices.
Record and Connect Buttons
The Record button on the remote control will allow you
to begin a recording or schedule a delayed recording using
NetCommand. The CONNECT button allows you to
establish a peer-to-peer connection between two IEEE
 devices connected to the HDTV Receiver network.
Note: To the left is a list of devices by several
manufacturers that have been tested and shown to be
compatible with the NetCommand control system.
When you use these devices you will be able to control
them without changing the setting of the remote control
from Cable/DBS/DTV to another product. Since
similar devices from the same manufacturer often operate
the same way, other models may be compatible, however
they have not been tested so not all NetCommand
functions may be available. For devices that are not
supported by NetCommand, you will need to use that
device’s original remote control or program the HDTV
Receiver remote to operate these devices in the traditional
manner.
You need to program your HDTV Receiver
remote to operate the NetCommand features.
1. Move the slide switch at the top of the
Remote Control to the Cable/DBS/DTV
position.
2. Press and hold on the POWER button.
3. While holding on the POWER button,
enter the number for NetCommand 197.
4. Release the POWER button.
IMPORTANT
Track List
The Track List allows you to play, select or delete the
programs stored on your IEEE  AV Disc.
NetCommand® Setup
For NetCommand traditional devices, the NetCommand
Setup should have been completed. The NetCommand
Setup will detail what type and brand of devices are
connected and how these devices are connected to the
HDTV Receiver and A/V Receiver. In addition, you
need to connect IR Emitters to the HDTV Receiver
connection labeled IR Output NetCommand. IR
Emitter ends should be properly placed in front of each
NetCommand IR device. You will need to make this
connection in order to control NetCommand IR devices.
The remote control needs to be programmed to operate
NetCommand functions. See the HD- Owner’s Guide
for instructions on connecting IR compatible devices, using
the NetCommand Setup and programming the remote
control.
Non-NetCommand IR Devices
When you are using a non-NetCommand compatible
device, select the device on the Device Selection menu and
press ENT(er). Then move the slide switch at the top of
your remote control to the appropriate layer and point the
remote control at the device to control it, or you will need
to use the remote control that came with that device.
Special Features
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HD5000A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HD5000A in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info