549872

Mitsubishi HC8000D Manual

18
Zoom out
Zoom in
Previous page
1/55
Next page
EN-18
C. Projecting images
Preparation:
• Removethelenscap.
• Turnonthepoweroftheconnectedvideoequipment.
COMPONENT button
POWER button
COMPUTER/
COMPONENT button
ON ( I ) button
HDMI 1/2 button
HDMI/COMPUTER button
STATUS indicator
POWER indicator
t, u buttons
1. Confirm the POWER indicator lights-up red.
• Iftheprojectorwasturnedoffbeforethelamphadcooleddownsufciently,thefanmaystartrotatingandthe
POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the
fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Press the POWER button on the projector or ON ( I ) button on the remote control.
• Itmaytakeaboutoneminuteforthelamptolightup.
• Thelampfailstolightuponrareoccasions.Insuchacase,waitforafewminutesandthentryagain.
• Donotcoverthelenswiththelenscapwhilethelampison.
• AfterthePOWERbuttonispressed,theimagemayickerbeforethelampbecomesstable.Thisisnota
product malfunction.
• TheSTANDARDlampmodeisactivatedbydefaultwhenevertheprojectoristurnedon.WhentheLOWLAMP
MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.
• TheprojectorstartswarmingupwhenthePOWERbuttonispressed.Duringthewarm-upprocess,images
may appear dark and no commands are accepted.
• Byblinkingred,theSTATUSindicatorindicatesthatthelampshouldbereplacedsoon.Replacethelampwhen
the STATUS indicator blinks red. (See page 51.)
3. Adjust the focus by turning the focus ring.
• Youarerecommendedtoadjustthefocusatthescreencenter.
4. Select an input source.
• PresstheCOMPONENTorHDMI/COMPUTERbuttonontheprojectorortheCOMPUTER/COMPONENTor
HDMI 1/2 button on the remote control that is corresponding to the terminal in use.
• TheinputsourceisswitchedbetweenCOMPUTER,HDMI1andHDMI2everytimeyoupresstheHDMI/
COMPUTER button on the projector.
• TheinputsourceisswitchedbetweenCOMPUTERandCOMPONENTeverytimeyoupresstheCOMPUTER/
COMPONENT button on the remote control.
•
The input source is switched between HDMI1 and HDMI2 every time you press the HDMI 1/2 button on the remote control.
• Theprojectorautomaticallyselectstheappropriatesignalformat.(Theselectedsignalformatisdisplayedon
the INFORMATION menu.)
• Youcannotchangetheinputsourcewhilethemenuisbeingdisplayed.
• Thoughitmaytakesometimebeforeanimageisdisplayedonthescreendependingonthetypeoftheinput
signal, such symptom is not a malfunction.
• Someimagesbecomeeasiertoviewwhenthesettingofaspectratioischanged.(Seepage20.)
• WhenthisprojectorisconnectedwithanHDMIdevicesupportingHDCP,suchasaDVDplayer,imageisnot
displayed correctly at the time of switching the input source on rare occasions. In such cases, switch to other
input source and then switch back to the HDMI input source.
• WhenCOMPONENTischosenasthesource,imagessuppliedfromthecomputermayicker.Pressthet or
u button on the remote control to reduce flicker, if it occurs. (Fine adjustment)
5. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specified sizes.
6. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 12.)
7. Adjust the image size by turning the zoom ring.
8. Adjust the vertical position of the displayed image by turning the LENS SHIFT dial.
If necessary, adjust the focus and zoom again.
Viewing video images (continued)
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HC8000D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HC8000D in the language / languages: English as an attachment in your email.

The manual is 7,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info