215751
42
Zoom out
Zoom in
Previous page
1/47
Next page
EN-42
Others
Problem Solution
The exhaust vents
emit warm air.
This air comes out after cooling the inside of the projector. You may feel hot, but this
is not a malfunction.
The menu can’t be
used.
The microcomputers inside the projector may be wrongly operating because of noise.
Press the POWER button to turn off the lamp and wait about 2 minutes. Then
unplug the power cord from the outlet, wait at least 10 minutes, and plug the
power cord back into the outlet. When the POWER button doesn't function, unplug
the power cord from the outlet, wait at least 10 minutes, and then plug the power
cord back into the outlet.
J
“TEMPERATURE!!” is
displayed.
This indication appears when the ambient temperature rises high. When the ambient
temperature stays high, the lamp goes out.
Eliminate any causes of the rise in the ambient temperature.
This indication appears when the air inlet or outlet grille is blocked. When they are
kept blocked, the lamp goes out.
Remove the objects blocking the air inlet or outlet grille. Clean the fi lter, if clogged.
(See pages 38 and 39.)
J
J
The
mark appears.
This mark appears when ineffective operation is carried out. This isn’t a product
malfunction.
The remote control
doesn’t function easily
or at all.
Check that the batteries are loaded in the remote control or the batteries are not
weak. (See page 6.)
Check that the remote control sensor isn’t exposed to direct sunlight or fl uorescent
light. (See page 9.)
Use the remote control within its operation range. (See page 9.)
Use the remote control at least 10 cm away from the projector.
The buttons on the
control panel (except
for the POWER
button) don’t function.
PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to
enable the password lock.
Cancel the password lock or contact the person in charge of management of the
projector. (See page 35.)
J
Mechanical operating
noise (clicking sound)
is heard.
The iris produces sound while operating. This is not a malfunction.
If the following problem occurs after the lamp is replaced, check the following fi rst.
Problem Solution
The projector does not
turn on.
Fit the lamp cover securely. (See pages 36 and 37.)
Reset the lamp operating time. (See page 37.)
The STATUS indicator
blinks.
Reset the lamp operating time. (See page 37.)
Troubleshooting (continued)
Images are not displayed correctly. (continued)
Problem Solution
Different color tint. When comparing images projected by two projectors, tints in the displayed images
may be different because of variation between their optical components. This is not a
malfunction.
When comparing the image projected by this projector with those displayed on the
television or PC monitor, tints in the displayed images may be different because of
difference in the range of color reproducibility. This is not a malfunction.
Only the motion areas
in the images supplied
from the computer
aren’t displayed.
This is caused by the computer being used. Contact the manufacturer of your
computer.
Projected images are
obscured.
Match the output resolution of your computer with the resolution of the projector.
For the method to change the output resolution of the computer, contact the
manufacturer of your computer. (See page 45.)
Image remains
freezing.
When image from VCR is projected, it may remain freezing during speed search. This
is not a malfunction.
Noise appears around
the image.
In some images such as DVD, noise may appear around the recorded image. In this
case, decrease the setting value of OVER SCAN of the SIGNAL menu. (See page 29.)
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi hc5500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi hc5500 in the language / languages: English as an attachment in your email.

The manual is 6,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi hc5500

Mitsubishi hc5500 User Manual - Dutch - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info