493687
13
Zoom out
Zoom in
Previous page
1/48
Next page
EN-13
Setting up your projector (continued)
Front projection, ceiling mounting
For ceiling mounting,
you need the ceiling
mount kit designed for
this projector. Ask a
specialist for installation.
For details, consult your
dealer.
The warranty on this projector does not cover any
damage caused by use of any non-recommended
ceiling mount kit or installation of the ceiling mount
kit in an improper location.
When using the projector mounted on the ceiling,
set IMAGE REVERSE in the INSTALLATION menu
to MIRROR INVERT. See page 27.
When the projector is mounted on the ceiling,
images may appear darker than those projected in
the case of tabletop mounting. This isn’t a product
malfunction.
Ask your installation specialist to provide an A/C
power switch. When you do not use the projector, be
sure to shut down the main power by the switch.
Do not install the projector where the exhaust vents
are exposed to air emitted by an air conditioning.
Such installation may cause a breakdown.
Do not install the projector near a fire alarm
because it emits hot air from its exhaust vents.
Rear projection
Ask a specialist for
installation. For details,
consult your dealer.
For rear projection,
set IMAGE
REVERSE in the
INSTALLATION
menu to MIRROR. See page 27.
Caution:
Placing the projector directly on a carpet impairs
ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate
ventilation.
Place the projector at least 50 cm (or 20 inch)
away from the wall to prevent the air inlet grille
and the air outlet grilles that emit hot air from
being blocked.
Do not use the projector in the following locations
and manners, which may cause fire or electric
shock.
In a dusty or humid place.
In a sideways position, or with the lens facing
down.
Near a heater.
In an oily, smoky, or damp place such as a kitchen.
In direct sunlight.
Where the temperature rises high, such as in
a closed car.
Where the temperature is lower than +41°F
(or +5°C) or higher than +95°F (or +35°C ).
Important:
Do not apply force to the lens, because the lens may
be damaged.
Be sure to use this projector at an altitude of less than
1500 meters.
TRIGGER terminal
The TRIGGER terminal on the rear of the projector
is a terminal that outputs a 12 V signal to control an
externally connected device (electric screen) when
images are projected.
Ring (NC)
To externally
connected device
Tip (12 V)
(Ground 0 V)
TRIGGER
To use the TRIGGER terminal, set TRIGGER OUT
to SCREEN or ANAMORPHIC in the INSTALLATION
menu. (The factory default is OFF. See page 27 for
details.) Use the following steps to change the setting.
With the INSTALLATION menu:
(See page 26 for menu setting.)
Display the INSTALLATION menu.
Select TRIGGER OUT by pressing the p or q
button.
Select SCREEN or ANAMORPHIC by pressing the
t or u button.
To cancel the menu:
Press the MENU button.
Caution:
Do not use the signal output from the TRIGGER
terminal as a power for other devices.
Do not link the TRIGGER terminal with an audio
terminal of other device because that device may be
damaged.
The rated current for the TRIGGER terminal is
200 mA. If you use a current exceeding this rating, a
failure may occur.
For information about electric screens, please
contact screen manufacturers.
1.
2.
3.
4.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi HC3200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi HC3200 in the language / languages: English as an attachment in your email.

The manual is 6,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi HC3200

Mitsubishi HC3200 User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info