587204

Mitsubishi FDTC Manual

14
Zoom out
Zoom in
Previous page
1/22
Next page
13
WHEN THE CHECK INDICATOR LIGHT (RED) FLASHES
INSPECTION DISPLAY, FILTER SIGN, AIR CONDITIONER NUMBER, STANDBY, ROOM TEMPERATURE AND BACK UP DISPLAY
< WIRED REMOTE CONTROL >
The air conditioner stops in the event
any trouble occurs.
At the same time, the check indicator
light flashes in red and the error code is
displayed in the ON timer display area and
the following is displayed in the display
area.
“
” ⇔ “ ”
(Air conditioner number)
Ç
(lights for 2 seconds by turns)
Error code
Air conditioner No.
1
Press AIR CON No. button.
Enter AIR CON No. display mode.
2 Press ▲ button.
AIR CON No. and error codes are
displayed in order from the lowest.
Press ▼ button to display in the
reverse order.
3 Press button.
Return to the AIR CON of the lowest
number.
1 2
ERROR display when multiple indoor units are connected
If errors have occurred for all the connected air conditioning unit.
Initially, the error display shows the formation of the air
conditioning unit whose number is the lowest.
Errors of other air conditioning unit can be checked with the
following procedure.
1
Press AIR CON No. button.
AIR CON No. display mode appears.
2 Press ▲ button.
AIR CON No. are displayed in order
from the lowest. And error codes are
displayed on the unit in trouble.
Press ▼ button to display in the
reverse order.
3 Press button.
Return to the AIR CON of the lowest
number.
If errors have occurred for some of the connected AIR CON
units.
Only the units for which errors have occurred stop operating.
The remote control shows the operating units.
NOTICE
• If button is pressed once while errors are displayed,
the errors display is turned off, and return to the stop mode.
If
button is pressed again, the errors are displayed.
HOW TO DISPLAY AIR CON NO.
By operating AIR CON No. button, the number of the connected AIR CON
unit and error codes of the units which have the record are displayed.
1
Press AIR CON No. button.
AIR CON No. display mode appears
and the AIR CON of the lowest number
is displayed. Other displays all turn off.
2 Press ▲ button.
AIR CON No. are displayed in order
from the lowest. And error codes are
displayed on the units which have
suffered from failure in the past.
Press ▼ button to display in the
reverse order.
3 Press button.
Return to the original display.
1 2
NOTICE
• The AIR CON No. can be displayed without relation to its modes of
operation, stop, forcible stop due to an error.
• Buttons other than “AIR CON No.” “▲” “▼” “ON/OFF” cannot be
operated.
1 2
STANDBY DISPLAY
During the first operation after breaker power supply input or the
recovery from power failure, “
” can be displayed on
the remote control for max 30 minutes.
The refrigerant oil protection control is activated to protect the
compressor and this isn’t a failure. Please wait till the display turns
off.
WHEN THE FILTER CLEANING MESSAGE IS DISPLAYED
The “ ” is displayed
When the cumulative operation time
reaches set amount number of hours in
order to notify the time for cleaning.
Clean the air filter. See page 16
“FILTER CLEANING” is displayed in the
display area. It is displayed for one second
every five seconds while the unit is running.
It is always lit while the system stopped.
After cleaning
1 Press RESET button.
The cumulative operation hours is
reset and the “FILTER CLEANING”
message turns off.
1
ROOM TEMPERATURE DISPLAY
If room temperature display setting is activated, room temperature is
displayed on the remote control display. Then airflow display turns off,
but airflow adjusting button is operative. Consult your dealer for settings.
Ç
The room temperature display
WIRELESS REMOTE CONTROL
• All displays are described in the liquid crystal display for explanation
OPERATION MODE display
Indicates selected operation with .
FAN SPEED button
Every time this button is pressed, the mode is switched
as below.
HI MED LO
ROOM
*
TEMP display
Indicates set temperature.
FILTER display
Indicates for two seconds when FILTER
button is pressed.
(AUTO) (COOL) (HEAT)
(FAN) (DRY)
ROOM
*
TEMP/TIME SETTING button
Sets room temperature by pressing or button.
Sets time when setting the time.
ACL switch
Used to reset the microcomputer.
FAN SPEED display
Indicates the selected airflow volume.
FILTER button
TIMER CANCEL button
Used to cancel the TIMER SETTINGS.
Transmitter
Sends signal to the air conditioner.
Used to reset (turn off) the filter sign.
Press the button only after completing the filter cleaning.
Operation section Display section
OPERATION MODE select button
(Dehumidifying
operation is prohibited for FDU-F.)
Every time this button is pressed, displays switch as below
ON/OFF button
When this is pressed once, the AIR CON starts to operate
and when this is pressed once again, it stops operating.
14
14
14
14
14
15
14
14
15
When you press each button of wireless remote
control, directing properly to the receiving part of
the air conditioner, the signal is transmitted. If the
air conditioner receives the signal correctly, the light
of operation indicator will flash.
ATTENTION
The operation of remote control must be performed
slowly and steadily.
HOW TO OPERATE
ABOUT REMOTE CONTROL HOLDER
The remote control can be mounted on the wall or
pillar with the remote control holder.
Slide from the upper part of the holder to place or
take out the remote control.
ATTENTION
Do not place the remote control to the following places.
•
The place exposed to direct sunlight or other strong
lighting.
•
The place exposed to high temperature, for
EXAMPLE, on the electric carpet or near a stove.
If the signal receiving part of the air conditioner is
exposed to direct sunlight or other strong lighting, it
may not receive the signal. In this case, shut out the
sunlight or turn down the lighting.
Do not place anything between the remote control and the unit.
Do not operate the remote control for other electric
appliances which can be operated with a remote control.
Handle it with utmost attention.
Remove the batteries when the remote control is
not used for a long time.
Even if the remote control is not found or damaged,
you can operate the air conditioner with itself. See
“How to use the backup button” on page 15.
NOTICE
If the display of remote control has troubles, press RESET switch.
WIRELESS REMOTE CONTROL HANDLING PROCEDURE
REPLACING THE BATTERIES
1 Pull out the cover.
2 Replace the old
batteries with
new ones.
(R03×2)
3 Close cover.
4 Adjust the current time.
See page 14
When any error occurs on the
display,
Press
ACL
switch with
a ballpoint
etc.
NOTICE
If the remote control is set as “Radio
Interference Prevention Setting”, it
returns to default when the batteries
are removed. It is necessary to perform
the next procedures again.
If the following occurs, the batteries are exhausted. Replace with new ones.
• When the signal is transmitted, the AIR CON does not display reception.
• The display fades away or does not show anything.
How to set Radio Interference
Prevention Setting
It is possible to sent two way. Press
ACL
switch with
AIR FLOW
button kept pressing or Insert the
batterles with
AIR FLOW
button
kept pressing.
ATTENTION
• Do not use old and new batteries
mixed.
• Remove the batteries when the
remote control is not used for a long
time.
•
The recommendable effective period
of a battery is about 6 to 12 months.
(It depends on the usage.)
When the batteries are inserted, each operation mode
is set as the right figure. Adjust the current time referring
to page 14. (The figure is for operation, and only the
current time is displayed for stopping)
Pay attention
to the and
marks
• The recommendable effective
period is printed on the battery.
This may be shorter due to
manufacturing time of the unit.
• However the battery may be still
working in order after expiry date.
NAMES AND FUNCTIONS OF REMOTE CONTROL BUTTON <WIRELESS REMOTE CONTROL>
BACK UP DISPLAY
If the back up display appears on the screen,. Please contact the
dealer where the unit was purchased.
The back up display is indicated per 1 second at intervals of 5
seconds when the air conditioners is in operation.
Automatic operation of the KX (except KXR) cannot be
selected. When automatic operation is selected in this unit,
set the remote controller to disabled the automatic operation.
While pressing the
MODE
button ant then press the
ACL
switch, or while pressing the
MODE
button and
then insert the batteries to the remote controller, then it
has been disabled the automatic operation.
ATTENTION
When the batteries are removed in the remote
controller once, the system is returned to initial
setting (automatic enable setting). In case that
removing the batteries in the remote controller,
perform the above operation once again.
SETTING CHANGE OF AUTOMATIC OPERATION
IN case of FDU-F
The setting temperature of the remote controller indicates the outdoor temperature
while operating thermostat ON/OFF.
IN case of FDU-F
The setting temperature of the remote controller indicates the
outdoor temperature while operating thermostat ON/OFF.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi FDTC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi FDTC in the language / languages: English as an attachment in your email.

The manual is 10,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mitsubishi FDTC

Mitsubishi FDTC User Manual - German - 22 pages

Mitsubishi FDTC User Manual - Dutch - 22 pages

Mitsubishi FDTC User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info