493681
33
Zoom out
Zoom in
Previous page
1/59
Next page
EN-33
ENGLISH
1. Repeat steps 1-2 above.
2. Press to highlight Volume and press / to select a desired sound level.
Standby Audio Out
Selecting On enables the function. The projector can output an Audio input signal when it is in standby mode and
Audio input and Audio out jack is correctly connected to devices.
When the projector enters standby mode, the audio will be interrupted briefly. This is not a product malfunction.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect
the projection settings, operation, or performance.
Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the
OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second
increments. Use / to select a suitable time frame.
Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five
locations. Use / to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to
select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during
projector start-up. Use / to select a screen.
Shutting down the projector
1. Press POWER and a confirmation message displays prompting you.
If you don't respond in a few seconds, the message will disappear.
2. Press POWER a second time. The POWER indicator light flashes
orange, the projection lamp shuts down, and the fans will continue to run
for approximately 90 seconds to cool down the projector.
3. Once the cooling process finishes, the POWER indicator light is a
steady orange and fans stop.
4. Disconnect the power cord from the wall socket if the projector will not
be used in an extended period of time.
To protect the lamp, the projector will not respond to any commands during the
cooling process.
To shorten the cooling time, you can also activate the Quick Cooling function.
See "Quick Cooling" on page 45 for details.
Do not unplug the power cord before the projector shutdown sequence is
complete or during the 90-second cooling down process.
If the projector is not properly shut down, to protect the lamp, when you attempt
to re-start the projector, the fans will run for a few minutes to cool down. Press
POWER again to start the projector after the fans stop and the POWER
indicator light turns orange.
Direct power off
1. The AC power cord can be pulled out during the projector is on. To protect the lamp, wait about 10 minutes
before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes
to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER
indicator light turns orange.
2. To protect the lamp, do not shut down the projector while the POWER indicator light is blinking green after
the lamp lights up.
3. Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without
closing the menu, the setting data of the menu may not be saved.
4. If you shut down the projector while controlling the projector using the network function, the application
software such as e-Control™ may fail. In this case, close the application software first. After the connection
between the projector and the computer re-establishes, initialize the software again.
I
I
I
I
I
I
I
I
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi EX321U-ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi EX321U-ST in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info