493684
37
Zoom out
Zoom in
Previous page
1/58
Next page
EN-37
ENGLISH
iv. Once set, access to the remote network operation page on this projector has been password-protected.
To enable this function, check the box in front of "Enable" and type in your desired password in the
New Password column and confirm the new password by re-entering the new password at the Confirm
column. To disable password protection, uncheck the box.
v. Once set, access to the Tools page has been password-protected. Refer to step iv for how to use the
password function.
After making the adjustments, press the Send button and the data will be saved in the projector.
Once the password is set, the Log Out button will display beside the Tools button.
Write down your selected password in advance or right after the password is entered so that it is available to you should
you ever forget it. If you forget the password, you will not be able to log in.
The software is available in English language.
When DHCP is turned on, there is a possibility of stopping the webpage connection. If this happens, please check the new
IP address of the projector and enter the new address to connect again.
vi. Press Exit to go back to the remote network operation page.
4. The Info page displays the information and status of this projector.
i. The information you entered in the Tools page will display here and these columns are empty when
you use e-Control™ for the first time.
ii. When the projector is in abnormal conditions, the following information will display.
When the projector is in normal conditions or in any abnormal conditions other than the ones mentioned below, the Error
Status column will be empty.
(3 = Error; 1 = notice)
iii. Press Exit to go back to the remote network operation page.
5. After pressing the button ‘Contact IT Help’, the HELP DESK window will appear at the upper right corner. You
will be able to deliver messages to RoomView™ software which is connected to the same local area network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Controlling the projector using PJLink™ application
This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector's
operations using the same application among projectors of different models and different manufacturers.
About PJLink™
To use PJLink™ function, the PJLink™ application software is required.
Error Status Description
3: Lamp fail The lamp fails to ignite or turns off during operation.
3: Over Temp The projector temperature is too high or cannot be detected.
3: Fan Lock The fan rotation speed cannot be set or detected.
1: Over Lamp Usage time The lamp is still in use after the lamp warning messages display.
ii
iii
i
i
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi EX320U-ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi EX320U-ST in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info