493684
20
Zoom out
Zoom in
Previous page
1/58
Next page
EN-20
Operation
Starting up the projector
1. Plug the power cord into the projector and into a wall socket. Turn on the
wall socket switch (where fitted). Check that the POWER indicator light
on the projector lights orange after power has been applied.
Ask your installation specialist to provide an Earth leakage breaker. When you do
not use the projector, be sure to shut down the main power by the breaker.
Please use the original accessories (e.g. power cord) only with the device to
avoid possible dangers such as electric shock and fire.
In order to ensure the safety in case of trouble with the projector, use an
electrical outlet having an earth leakage breaker to supply the power to the
projector. If you do not have such outlet, ask your dealer to install it.
2. Remove the lens cap. If it is closed, it could become deformed due to the
heat produced by the projection lamp.
3. Press POWER on the projector or remote control to start the
projector. The POWER indicator light flashes green and stays green
when the projector is on.
The start up procedure takes about 30 seconds. In the later stage of start up,
a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fans for
approximately 90 seconds before energizing the lamp.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes
before turning it off.
After POWER is pressed, the image may flicker before the lamp becomes
stable. This is not a product malfunction.
4. If the projector is activated for the first time, select your OSD language
following the on-screen instructions.
5. If you are prompted for a password, press the arrow keys to enter a six-
digit password. See "Utilizing the password function" on page 22 for
details.
6. Switch all of the connected equipment on.
7. The projector will start to search for input signals. The current input
signal being scanned appears in the upper left corner of the screen. If the
projector doesn't detect a valid signal, the message 'No Signal' will be
displayed until an input signal is found.
You can also press SOURCE on the projector or remote control to select
your desired input signal. See "Switching input signal" on page 23 for
details.
If the frequency/resolution of the input signal exceeds the projector's operating
range, you will see the message 'Out of Range' displayed on a blank screen. Please
change to an input signal which is compatible with the projector's resolution or set
the input signal to a lower setting. See "Timing chart" on page 55 for details.
I
I
I
I
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi EX320U-ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi EX320U-ST in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info