493643
41
Zoom out
Zoom in
Previous page
1/49
Next page
EN-41
ENGLISH
Replacing the lamp Spare lamp for EX200U/ES200U: VLT-EX240LP
Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for
purchase of the lamp.
To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the
lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that
has shattered into sharp pieces. To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may
also result in fire.
If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments
may fall out and cause injury to your eyes.
In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector.
Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by
yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.
Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.
Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a
breakdown.
This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or
fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until
explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions.
Therefore, the lamp may explode soon after the start of use.
The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of
lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.
When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas
charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful
not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth,
see a doctor immediately.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.
Be sure to use the lamp dedicated to this projector, VLT-EX240LP for EX200U and ES200U. Use of other lamps may cause
a failure of the projector.
1. Turn the power off and disconnect the projector from the wall
socket. If the lamp is hot, avoid burns by waiting for approximately
45 minutes until the lamp has cooled.
2. Unscrew the screws on the lamp cover.
3. Remove the lamp cover from the projector.
,
Pull up the lamp cover, pussing up the allow parts of the front panel.
Do not turn the power on with the lamp cover removed.
Do not insert your fingers between the lamp and the projector. The sharp
edges inside the projector may cause injuries.
4. Remove and dispose of the lamp protection film.
5. Loosen the screw that secures the lamp.
1
2
3
1
2
2
3
2
1
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mitsubishi EX200U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mitsubishi EX200U in the language / languages: English as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info