790898

Mio MiVue 886 Manual

8
Zoom out
Zoom in
Previous page
1/30
Next page
7
3. When adjusting the angle of mounting, make sure that the camera’s view is
parallel with the level ground and the ground/sky ratio is close to a 50/50 split.
* 50/50
Using the device mount
U-type mount (Figure 1-A)
O-type mount (Figure 2-B)
Install your Mio on the motorcycle or helmet by using the
provided device mount.
Using the charging cable
USB charging cable (Figure 2-A)
5V USB waterproof charging cable (Figure 2-B)
You should fully charge the battery before you start using
it for the very rst time. To charge the battery, plug the
provided charging cable into the Micro-USB connector on
your Mio and the other end into a power source (5V DC /
2A; not provided).
Using the power cable
12V waterproof power cable (Figure 2-C)
Check and conrm the motorcycle wire by using the
electricity tester.
Connect the red wire (ACC) of the power cable to the
motorcycle wire from which the power is not supplied
when the motorcycle is turned off.
The black wire (GND) must be connected to the metal
part of the motorcycle for grounding. If not grounded, this
product may not work properly. You can use a screw to
attach the black wire to the motorcycle (try to nd a screw
hole on any metal part).
Using the rear camera kit
Rear camera with 12V waterproof power cable (Figure
2-D)
Rear camera with 5V USB charging cable (Figure 2-E)
Follow the previous instructions to connect the power
cable / charging cable, and then connect the rear camera.
Installing the ferrite cores
Depending on your model, ferrite cores may be provided
to eliminate electromagnetic interference. Follow the
instructions (Figure 2-F) to install the ferrite cores on the
rear camera cable.
EN
Revision: R00
(7/2019)
5615N6280002 R00
D
E
F
12
1
2
A
A
B
B
1
2
3
Torque: 15kgf.cm
1
2
4
3
ACC
GND
1
2
12
10 cm 10 cm
Using the device mount
U-type mount (Figure 1-A)
O-type mount (Figure 2-B)
Install your Mio on the motorcycle or helmet by using the
provided device mount.
Using the charging cable
USB charging cable (Figure 2-A)
5V USB waterproof charging cable (Figure 2-B)
You should fully charge the battery before you start using
it for the very rst time. To charge the battery, plug the
provided charging cable into the Micro-USB connector on
your Mio and the other end into a power source (5V DC /
2A; not provided).
Using the power cable
12V waterproof power cable (Figure 2-C)
Check and conrm the motorcycle wire by using the
electricity tester.
Connect the red wire (ACC) of the power cable to the
motorcycle wire from which the power is not supplied
when the motorcycle is turned off.
The black wire (GND) must be connected to the metal
part of the motorcycle for grounding. If not grounded, this
product may not work properly. You can use a screw to
attach the black wire to the motorcycle (try to nd a screw
hole on any metal part).
Using the rear camera kit
Rear camera with 12V waterproof power cable (Figure
2-D)
Rear camera with 5V USB charging cable (Figure 2-E)
Follow the previous instructions to connect the power
cable / charging cable, and then connect the rear camera.
Installing the ferrite cores
Depending on your model, ferrite cores may be provided
to eliminate electromagnetic interference. Follow the
instructions (Figure 2-F) to install the ferrite cores on the
rear camera cable.
EN
Revision: R00
(7/2019)
5615N6280002 R00
C
ACC
GND
12
E
F
12
1
2
A
A
B
B
1
2
3
Torque: 15kgf.cm
1
2
4
3
12
10 cm 10 cm
Using the device mount
U-type mount (Figure 1-A)
O-type mount (Figure 2-B)
Install your Mio on the motorcycle or helmet by using the
provided device mount.
Using the charging cable
USB charging cable (Figure 2-A)
5V USB waterproof charging cable (Figure 2-B)
You should fully charge the battery before you start using
it for the very rst time. To charge the battery, plug the
provided charging cable into the Micro-USB connector on
your Mio and the other end into a power source (5V DC /
2A; not provided).
Using the power cable
12V waterproof power cable (Figure 2-C)
Check and conrm the motorcycle wire by using the
electricity tester.
Connect the red wire (ACC) of the power cable to the
motorcycle wire from which the power is not supplied
when the motorcycle is turned off.
The black wire (GND) must be connected to the metal
part of the motorcycle for grounding. If not grounded, this
product may not work properly. You can use a screw to
attach the black wire to the motorcycle (try to nd a screw
hole on any metal part).
Using the rear camera kit
Rear camera with 12V waterproof power cable (Figure
2-D)
Rear camera with 5V USB charging cable (Figure 2-E)
Follow the previous instructions to connect the power
cable / charging cable, and then connect the rear camera.
Installing the ferrite cores
Depending on your model, ferrite cores may be provided
to eliminate electromagnetic interference. Follow the
instructions (Figure 2-F) to install the ferrite cores on the
rear camera cable.
EN
Revision: R00
(7/2019)
5615N6280002 R00
C
D
ACC
GND
12
E
F
12
1
2
A
A
B
B
1
2
3
Torque: 15kgf.cm
1
2
4
3
ACC
GND
1
2
12
10 cm 10 cm
*
Note: The installation illustrations are for your reference only. The placement of the devices and
cables may vary depending on the vehicle model. If you encounter any problems during installation,
contact a skilled installer (such as the service personnel of the vehicle) for assistance.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mio MiVue 886 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mio MiVue 886 in the language / languages: English as an attachment in your email.

The manual is 0.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info