Manual Minolta Vectis 200 (page 4 of 4) (English)

42268

Zoom out

Zoom in

1/4

TECHNICAL SPECIFICATIONS

Camera Type: IX240 Lens Shutter Camera

Lens: 25-50mm f/4.8-9.1 power zoom lens

Focusing range: C/H: 0.5m - ∞ (1.64 ft - ∞)

P Wide: 0.5m - ∞ (1.64 ft - ∞), P Tele: 1.0m - ∞ (3.28 ft - ∞)

Film speed range: ISO 25-3200

Metering range (ISO 200):

25mm: EV 4 - 16.2

50mm: EV 4 - 17

Flash range(ISO 200):

25mm: 0.5 - 5.0m (1.64 ft.- 16.4 ft.)

50mm: 0.5 - 2.7m (1.64 ft. - 8.85 ft.)

Battery: One 3-volt CR2 lithium battery

Battery-condition indication:

3-stage indication

Battery performance:

Approx. 12 rolls (25 exp. roll w/ 50% flash)

Viewfinder: Magnification: 0.32X - 0.6X

Field of View (H format): 85% for subject at 3m (9.38 ft.)

Dimensions: 104 x 65 x 39mm (4-1/8 x 2-5/8x 1-5/8 in.)

Weight: 170g (6.0 oz.)

Specifications are based on the latest information available at the time of

printing and are subject to change without notice.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. Changes or modifications not

approved by the party responsible for compliance could void the user's authority to operate the

equipment. This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

This mark on your camera certifies that this camera meets the requirements of the EU

(European Union) concerning interference causing equipment regulations. CE stands for

Conformité Européenne (European Conformity).

TITLE IMPRINTING

Two titles from the title list sheet can be preset for use while taking pictures.

Either of the two preselected titles can be selected before the picture is taken.

The selected title is recorded on the film's magnetic strip, then printed on the

back of the print by your certified Advanced Photo System lab.

• Some labs may not be able to print the titles in all of the available languages. See your

photofinisher for details.

•Titles are displayed in the data panel as a title code. Please refer to the Title List for the

titles available with this camera.

*With the camera on and before taking the picture:

1.Press the title button to display the code

for the title you want.

*The sequence is as follows:

—> Title-1 —> Title-2 —> -- -- -- (no display)

2. Take the picture. The magnetic data is

written and the selection is canceled for

the next frame.

PRESELECTING TITLES

Two title codes have been set into memory. You can change one or both title

codes at any time.

1.Close the front cover to turn the camera

off.

2.Select the code for the title you want from

the title list sheet.

3.Press the title button to display the title

code you want to change.

To receive the best possible prints, take your film to a

photolab displaying the Certified Advanced Photo System

logo. Photofinishers displaying this logo have been

certified according to Advanced Photo System guidelines.

Certified photolabs will be able to provide the following services.

1.CHP - Print Format

Your film will be printed according to the format set when the picture

was taken.

2.Date and Title Imprinting

The date, time, and selected title are printed on the back of the picture

in the chosen format.

3.PQI - Print Quality Improvement

The lab will compensate (or not compensate) printing according to the

data recorded on the magnetic data strips.

4.Film is returned in the cassette

To keep the film dust free and aid in organization, film is returned in its

original film cassette. The VEI will be set to ■ to prevent accidental

5.Index Print

An index print showing a numbered image of each frame is included

with your returned order.

REPRINTS

Images are always captured in the H format (High-Vision). You can select any

of the three formats when ordering reprints.

CLEANING

• Keep the AF and AE windows clean or the focus and/or exposure may not be

accurate.

• If the camera body is dirty, gently wipe it clean with a soft, clean, dry cloth.

• To clean the lens surface, first brush away any dust or sand then, if necessary,

moisten a lens tissue with lens cleaning fluid and gently wipe the lens in a

circular motion, starting from the center.

• Never place lens fluid directly on the lens.

• Never touch the lens surface with your fingers.

• Never use alcohol or solvents to clean the camera.

STORAGE

When storing the camera for extended periods of time, please follow

these guidelines,

• Store the camera in a cool, dry, well-ventilated area away from dust and

chemicals. For very long periods, place the camera in an airtight container with

a silica gel drying agent.

• Before using after prolonged storage, always check the camera’s operation to

make sure it is functioning properly.

QUESTIONS AND SERVICE

• If you have questions about your camera, contact your local camera dealer or

write to the Minolta distributor in your area.

• Do not open the film chamber or forcefully remove the cassette if the film

cannot be rewound. Contact an authorized Minolta Service Facility.

• Before shipping your camera for repair, please contact an authorized Minolta

Service Facility for details.

BEFORE IMPORTANT EVENTS

• Check camera operation carefully or take test photographs.

• Minolta is not responsible for any loss which may occur due to an equipment

malfunction.

FILM CASSETTE WARNING

The film used in Advanced Photo System cameras stores some data

magnetically. Do not place the cassette on or near anything that creates a

magnetic field, such as a television or stereo speakers.

CAMERA ERROR

If all the indicators in the data panel blink, or the data panel is blank and the

camera will not function with a fresh battery, remove and reinsert the battery. If

normal operation does not resume, or the camera malfunctions repeatedly,

contact an authorized Minolta Service Facility.

CARING FOR YOUR CAMERA

LAB SERVICES

4.Press the select button, the last digit of the

title code number will blink.

5.Press the adjust button to change its

value.

• Press and hold the adjust button to change the value

rapidly.

6.Press the select button to make the next

digit blink, change its value using the

adjust button.

7.Press the select button to make the

language code blink.

8.Press the adjust button to change the

language code.

9.When the title information is correct, press

the title button.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Minolta Vectis 200 in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Minolta Vectis 200 Manual

Product: