20 21
PLH 30 XE PLH 32 XE
...........................................................
...........................................................
...........................................................
...........................................................
..................... 4151 96 01... ............... 4152 01 01...
..................... 4323 22 01... ............... 4322 94 01...
...000001-999999 ...000001-999999
.........................750 W ........................... 900 W
.........................375 W ........................... 450 W
.........................970 /min ...................... 1040 /min
.........................740 /min ........................ 800 /min
.......................4200 /min ...................... 4500 /min
..........................3,4 J .............................. 3,8 J
...........................30 mm .......................... 32 mm
...........................16 mm .......................... 16 mm
...........................40 mm .......................... 40 mm
...........................82 mm .......................... 82 mm
...........................43 mm .......................... 43 mm
..........................3,6 kg ............................ 3,6 kg
...........................95 dB ...................... 95 dB
.........................106 dB .................... 106 dB
...........................20 m/s
2
..........................25 m/s
2
..........................1,5 m/s
2
.........................2,3 m/s
2
...........................18 m/s
2
..........................20 m/s
2
..........................1,5 m/s
2
.........................1,5 m/s
2
ENGLISH
TECHNICAL DA Rotary Hammer
Production code.......................................................................
..............................................................................................
..............................................................................................
..............................................................................................
..............................................................................................
..............................................................................................
Rated input ..............................................................................
Output ......................................................................................
No-load speed .........................................................................
Speed under load max. ...........................................................
Rate of percussion under load max. ........................................
Impact energy per stroke according to EPT ....
Drilling capacity in concrete .....................................................
Drilling capacity in steel ...........................................................
Drilling capacity in wood ..........................................................
Light core cutter in bricks and limestone .................................
Chuck neck diameter ...............................................................
Weight according EPT ...........................
Noise Information
Measured values determined according to EN 60745.
T
Sound pressure level (K .......................................
Sound power level (K ............................................
Wear ear protectors!
Vibration Information
T
determined according to EN 60745.
Vibration emission value a
h
:
Hammer-drilling in concrete:
...............................................
Uncertainty K = ....................................................................
Chiselling: ............................................................................
Uncertainty K = ....................................................................
W
instructions. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a „live“ wire may make exposed metal
parts of the power tool „live“ and could give the operator an
electric shock.
Appliances used at many different locations including open
air should be connected via a residual current device of
30 mA
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or oor
electric cables and gas or waterpipes.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Under the effect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.
SPECIFIED CONDITIONS OF USE
The rotary pneumatic hammer can be used for hammer
drilling, chiselling in stone and concrete and drilling in wood,
metal as well as plastic.
Do not use this product in any other way as stated for
normal use.
W
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
ENGLISH
EC-DECLARA
We declare under our sole responsibility that the product
described under “T
regulations and the directives 201
2006/42/EC, 2004/108/EC and the following harmonized
standards have been used:
EN 60745-1:2009 +
EN 60745-2-6:2010
EN 55014-1:2006 +
EN 55014-2:1997 +
EN 61000-3-2:2006 +
EN 61000-3-3:2008
Winnenden, 2013-01-28
Alexander Krug
Managing Director
Authorized to compile the technical le.
T
Max-Eyth-Straße 10
71364 Winnenden
Germany
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to
after-sales service. This will ensure long service life and top
performance.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: T
Max-Eyth-Straße 10, 71364 Winnenden, Germany
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory
Do not dispose of electric tools together
with household waste material! In
observance of European Directive 2002/96/
EC on waste electrical and electronic
equipment and its implementation in
accordance with national law
that have reached the end of their life must
be collected separately and returned to an
environmentally compatible recycling
facility
Class II construction, tool in which
protection against electric shock does not
rely on basic insulation only
additional safety precautions, such as
double insulation or reinforced insulation,
are provided.
