24 25
W
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS Measuring Instrument
Never make measurement on a circuit in which voltage over
1000 V exists. Use only leads rated 1000 V or better
Disconnect the test leads from the instrument for current
measurement.
Keep ngers away from jaws during measurements.
T
and Capacitance measurements, never use the meter on an
energized circuit. Make sure a capacitor is fully discharged
before touching or attempting to make a measurement.
Do not attempt to make measurement in the presence of
ammablegasses. Otherwise, the use of the instrument may
cause sparking, which can lead to an explosion.
Never attempt to use the instrument if its surface or your hand
is wet.
Do not exceed the maximum allowable input of any measuring
range.
Only test on unenergized circuits unless absolutely necessary
Check tool functionality on a known circuit rst.Never
assume tool is working.
can be proven de-energized.
Do not ground yourself while measuring.
with earthed or grounded sur-faces such as pipes, radiators,
ranges and refrigerators.
Never remove the case or battery cover during a measurement.
This instrument is to be used only in its intended applications or
conditions. Otherwise, the instrument's safety functions may
not work, resulting in serious personal injury and instrument
damage.
T
wear personal protective equipment where live conductors are
exposed.
Never attempt to make measurement if any abnormal
conditions, such as broken case and exposed metal parts are
found on the instrument.
Do not rotate the Rotary Dial while the test leads are being
connected.
Do not install substitute parts or make any modication to the
instrument. For repair or re-calibration, return the tool to a
factory Service/Sales Support Branch or authorized service
station.
Only use Milwaukee test leads with the Milwaukee Clamp
Meters.Inspect test leads before each use. Use clamp meter to
run a continuity test.
Non-Contact V
The LED may not be displayed due to installation condition of
electrical circuit or equipment. Never touch the circuit under
test to avoid possible danger even if the LED for NCVD is not
displayed. Check the functionality of LED on a well-known
power supply prior to measurement. When the LED doesn’t
light up, do not make measurement. NCVD indication is
affected by external voltage, and how the meter is held or
placed.
Measurement categories and their signicance according
to IEC 61010-1:
CA
Measurements in the building installation: stationary
loads, distribution board, device rmly on the distribution board.
CA
Measurements at the source of low voltage: counter
main supply
For your present measuring instrument is valid the measuring
category and associated maximum rated voltage,
eg. 600 V CA
ENGLISH
TECHNICAL DA
Dial Position Range Resolution Accuracy
Current AC 200 A 0.1 A ±(3.0% +3dgt) 45-60Hz
V
400 V
1000 V
0.1 V / 1 V
:±(1.5% +5dgt) 45-500Hz
: ±(1.0% + 2dgt)
Resistance
Continuity
400 Ω
4 kΩ
40 kΩ
400 kΩ
4 MΩ
40 MΩ
0.1 Ω
0.001 kΩ
0.01 kΩ
0.1 kΩ
0.001 MΩ
0.01 MΩ
±(1% +5dgt)
±(1% +2dgt)
±(1% +2dgt)
±(1% +2dgt)
±(1% +2dgt)
±(2% +5dgt)
Low Input Impedance
400.0 V
1000 V
0.1 V / 1 V ±(2.0% + 3dgt)
Accuracy is specied for 1 year after calibration, at operating temperatures of 18°C to 28°C, with relative humidity
at 0 % to 85%.
Maximum voltage between any terminal and earth ground
CA
CA
1000 V
600 V
Jaw Opening (maximum conductor size) 16 mm
T -10°C - 50°C
T -40°C - 60°C
T
0,1 x specied accuracy /°C (<18°C or >28°C)
Operating
2000 m
Battery run time
>12 h with all functions
V 12 V Li-Ion
Weight according EPT
450 g
ENGLISH
SAFETY INSTRUCTIONS Battery
Do not try to replace the battery pack if the surface of the
instrument is wet.
Disconnect all the cords and cables from the object under test
and power off the instrument before removing or inserting the
battery pack.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System C 12 chargers for charging System C 12
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water
contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
This appliance is not intended for use by persons (including
children) with limited physical, sensory or mental capabilities or
insufcient experience and/or knowledge unless they are
supervised by a person who is responsible for their safety or
have been instructed by them in the safe use of the tool.
Children should be supervised in order to ensure that they do
not play with the tool.
SPECIFIED CONDITIONS OF USE
The Measuring Instrument can be used for following
measurements: Current
Resistance, Continuity
AC and DC at low input inpedance of the measurung
instrument,. This instrument may only use for measuring the
previously indicated measurements.
SLEEP FUNCTION
This instrument is automatically powered off in about 20 min
after the last Rotary Dial or button operation. T
the Rotary Dial or press a button.
WORKING TIPS
Set the Rotary Dial to an appropriate position before starting
measurement.
Firmly insert the test leads.
Disconnect the test leads from the instrument for current
measurement.
Do not expose the instrument to the direct sun, high
temperature and humidity or dew fall.
Altitude 2000 m or less.
within -10ºC and 50ºC.
This instrument isn’t dust & water proofed. Keep away from
dust and water
Be sure to power off the instrument after use. When the
instrument will not be in use for a long period, place it in
storage after removing the battery pack.
Use a damp cloth or neutral detergent for cleaning the
instrument. Do not use abrasives or solvents.
BA
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
T
performance of the battery pack.
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have
to be fully charged.
T
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the
label and order the drawing at your local service agents or
directly at: Milwaukee Electric T
D-71364 Winnenden, Germany
SYMBOLS
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national
law
of their life must be collected separately and
returned to an environmentally compatible
recycling facility
W
T
before opening case or removing battery
Ground
Double isolated
>1000 V
Never make measurement on a circuit in
which voltage over 1000V exists.
Keep ngers away from
test tips
during
measurements.
