630057
8
Zoom out
Zoom in
Previous page
1/40
Next page
14 15
2
>1000 V
1
Non-Contact Voltage Detection
Check the functionality of LED on a wellknown power supply
prior to measurement. When the LED doesn’t light up, do not
make measurement.
Kontaktlose Spannungsprüfung
Die Funktion der LED an einer bekannten Spannungsquelle
testen. Leuchtet die LED nicht, ist der Spannungsprüfer
defekt und darf nicht zu Messungen verwendet werden!
Détection de la tension sans contact
Tester la fonction des LED sur une source de tension
connue. Si la LED ne s’allume pas, cela signie que le
détecteur de tension est défectueux et qu’il ne doit pas être
utilisé pour des mesures!
Misurazione del voltaggio senza contatto
Testare il funzionamento del LED con una sorgente di
voltaggio nota. Se il LED non lampeggia, il voltmetro è
difettoso e non deve essere utilizzato per le misurazioni.
Detección de tensión sin contacto
Controle la función del diodo LED en una fuente de tensión
conocida. Si la lámpara LED no se enciende entonces el
comprobador de tensión está averiado y no deberá
emplearse para efectuar mediciones.
Teste de tensão sem contacto
Assegure-se de que a LED funciona, testando-a numa fonte
de tensão conhecida. Se a luz LED não começa a brilhar, o
detector de tensão está avariado e não deve ser utilizado
para medições!
Contactloze spanningscontrole
Test de functie van de led op een bekende spanningsbron.
Als de led niet brandt, is de spanningstester defect en mag
niet voor metingen worden gebruikt!
Kontaktløs spændingsprøvning
Afprøv LED-funktionen på en kendt spændingskilde. Lyser
LED’en ikke, er spændingstesteren defekt og må ikke
benyttes til målinger!
Kontaktfri spenningsprøving
Test LED funksjonen på en kjent spenningskilde. Lyser
LEDen ikke er spenningsindikatoren defekt og skal ikke
brukes til målinger!
Kontaktfri spänningsprovning
Testa LED-funktionen på en känd spänningskälla. Om LED:n
då inte lyser är det något fel på spänningsprovaren. Den får
då inte längre användas för mätningar!
Kosketukseton jännitteenmittaus
Tarkasta valodiodin toiminta tunnetun jännitteenlähteen
avulla. Jos valodiodi ei pala, niin jännitemittarissa on vika
eikä sitä saa enää käyttää mittauksiin!
Έλεγχος τάσης χωρίς επαφή
Δοκιμάζετε τη λειτουργία της λυχνίας LED σε μια γνωστή
πηγή τάσης. Όταν δεν φωτίζει η λυχνία LED, ο ελεγκτής
τάσης έχει βλάβη και δεν επιτρέπεται να χρησιμοποιηθεί για
μετρήσεις!
Kontakt yapılmaksızın voltaj kontrolü
LED fonksiyonunu bilinen voltaj kaynağında test edin. LED
ışık vermezse, voltaj kontrol cihazı arızalıdır ve ölçü yapmak
için kullanılamaz!
Bezkontaktní napěťová zkouška
Přezkoušejte funkci LED na známém zdroji napětí. Nesvítí-li
LED, je zkoušečka napětí defektní a nesmí se k měření
používat!
Bezkontaktná napäťová skúška
Preskúšajte funkciu LED na známom zdroji napätia. Ak LED
nesvieti, je skúšačka napätia defektná a nesmie sa k
meraniu používať!
Bezdotykowe sprawdzanie napięcia
Sprawdzić działanie lampki LED na znanym źródle napięcia.
Jeśli lampka LED nie świeci, oznacza to, iż wskaźnik
napięcia jest uszkodzony i nie można go używać do
pomiarów.
Feszültségvizsgálat érintkezés nélkül
Ellenőrizze le a LED működését egy ismert
feszültségforráson. Ha a LED nem világít, akkor a
feszültségvizsgáló hibás, és nem szabad mérésre használni!
Brezstični preizkus napetosti
Test funkcije LED na znanem izvoru napetosti. V kolikor LED
ne sveti, je indikator napetosti pokvarjen in ga ni dovoljeno
uporabljati za meritve!
Beskontaktna provjera napona
Funkciju LED-a testirati na jednom poznatom izvoru napona.
Ako LED ne svjetli, onda je ispitivač napona defektan i ne
smije se upotrebljavati za mjerenja!
Bezkontakta sprieguma pārbaude
Pārbaudīt LED funkcionalitāti pie zināma sprieguma avota.
Ja LED nemirgo, tad sprieguma mērītājs ir bojāts un tas
nedrīkst tikt izmantots mērījumiem.
Nekontaktinis įtampos tikrinimas
Patikrinti LED funkciją su žinomu įtampos šaltiniu. Jei
neužsidega LED parodymas, tai reiškia, kad įtampos
indikatorius yra sugedęs ir matuojant negali būti naudojamas!
Kontaktita pinge kontrollimine
Kontrollida LED funktsionaalsust tuntud pingeallika juures.
Kui LED ei vilgu, siis pingemõõtja on vigastatud ja seda ei
tohi kasutada mõõtmiste jaoks.
Бесконтактный контроль напряжения
Проверьте функциональность светодиода с помощью
известного источника питания. Если светодиод не
загорается, это говорит о неисправности индикатора
напряжения, и он не может использоваться для
проведения измерений.
Безконтактно измерване на напрежението
Функцията на LED светодиода трябва да бъде тествана с
познат източник на напрежение. Ако LED не мига, то
индикаторът на напрежение е дефектен и не трябва да
се използва за извършване на измервания !
Detectarea tensiunii fără contact
Se verică funcţionarea LED-ului la o sursă de tensiune
cunoscută. Dacă LED-ul nu se aprinde, detectorul de
tensiune este defect şi nu are voie să e folosit pentru
măsurători!
Контрола на напонот без контакт
Тестирајте го функционирањето на ЛЕД на некој познат
извор на напон. Доколку ЛЕД не свети, во тој случај
детекторот на напон е дефектен и не смее да се
употребува за мерења!
非接触电压测试
用已知的电压源检查LED功能。LED不发光时,电压测试器故
障并不能用于测量电压。
> 90 V
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Milwaukee C12 FM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Milwaukee C12 FM in the language / languages: All languages as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info