Manual Milwaukee 5262-59 (page 9 of 11) (English, French, Spanish)

641642

Zoom out

Zoom in

1/11

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tools by insulated gripping sur-

faces, when performing an operation where the

cutting tool may contact hidden wiring or its

own cord. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause can-

cer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

ciﬁ cally designed to ﬁ lter out microscopic particles.

SPECIFIC SAFETY RULES

SYMBOLOGY

Double Insulated

Volts Alternating Current

Watts

No Load Strokes per Minute

(SPM)

Seal of Electrical Security

Read operator's manual

Wear hearing protection

Wear eye protection

SPECIFICATIONS

Tool Capacities

Cat. No.

Volts

Load

RPM

Load

BPM

Rotary Hammer (concrete) Drill Only

Carbide Tipped

Percussion Bit

Thin Wall

Percussion

Core Bits

Twist

Drill Bit

(Wood)

Twist

Drill Bit

(Steel)

5262-59

5262-59A

5262-59B

220-240V 50-60 Hz

127V 50-60 Hz

800

0-1 500

0-5 625

7/8" 2-1/8" 1-1/8" 1/2"

1. Side handle

2. Clamp

3. Depth gauge rod

4. SDS Plus bit holder

5. Mode selector lever

6. Trigger

7. Forward/Reverse control switch

FUNCTIONAL DESCRIPTION

Fig. B

Fig. C

Fig. A

WARNING To reduce the risk of injury,

always use a side handle when using

this tool. Always brace or hold securely.

ASSEMBLY

WARNING To reduce the risk of injury,

always unplug tool before attaching

or removing accessories or making adjust-

ments. Use only speciﬁ cally recommended

accessories. Others may be hazardous.

Adjusting the Side Handle Position

1. Loosen the side handle by unscrewing the side

handle grip until the side handle rotates freely.

2. Rotate the side handle to the desired position.

3. Tighten the side handle grip securely.

WARNING To reduce the risk of injury

do not grasp the bit while the chuck is

rotating or while the bit is falling from the

chuck.

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of

electric shock. Check with a qualiﬁ ed electri-

cian if you are in doubt as to whether the

outlet is properly grounded. Do not modify

the plug provided with the tool. Never remove

the grounding prong from the plug. Do not

use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal. Your tool must

be plugged into an appropriate outlet, prop-

erly installed and grounded in accordance

with all codes and ordinances. The

plug and outlet should look like

those in Figure A.

Double Insulated Tools: Tools

with Two Prong Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insulation

system which satisﬁ es OSHA requirements and

complies with the applicable standards of Underwrit-

ers Laboratories, Inc., the Cana-

dian Standard Association and the

National Electrical Code. Double

Insulated tools may be used in ei-

ther of the 120 volt outlets shown in

Figures B and C.

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required.

If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be

sure it is marked with the sufﬁ x “W-A” (“W” in Cana-

da) to indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired by

a qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

Recommended Minimum Wire Gauge

for Extension Cords*

Extension Cord Length

* Based on limiting the line voltage drop to ﬁ ve volts

at 150% of the rated amperes.

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

25'

75'

100'

150'

50'

EXTENSION CORDS

Setting the Depth Gauge

1. Press in the clamping lever.

2. Slide the depth gauge rod backward or forward

until it is set for the desired depth.

NOTE: The drilling depth is the distance between

the tip of the bit and the tip of the rod.

3. Release the clamping lever.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Milwaukee 5262-59 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Milwaukee 5262-59 Manual

Product: