626789
8
Zoom out
Zoom in
Previous page
1/168
Next page
6millnorway.com
EN
Assembly
See figure 2 on separate illustration sheet
A. Drill holes in the wall for holes 1 & 2. Then drill holes in the wall for the topmost holes
(holes 3 & 4 by using 6).
B. Insert the wall plugs into the drilled holes and attach the bracket with 4 screws.
C. Place the heater on the lower lugs on the bracket, then hang the heater on the
upper lugs (lift the heater slightly to align the heater with for the upper lugs). Screw in
the locking screws on the top of the bracket (clockwise).
ATTENTION! HORIZONTAL PLACEMENT ONLY
Temperature calibration
See figure 3 on separate illustration sheet
It may occur deviation between the temperature registered by the heater and the actual
temperature in the room. This can be caused by several reasons, however, the most com-
mon is that the heater is placed in a fair distance from where you usually reside. When you
set the temperature to for example 22 degrees, it is only natural that you expect the same
temperature where your sofa is placed for instance. However, the temperature sensor is
placed on the product itself, and therefore a deviation in temperature may occur. To adjust
this, all Mill heaters are equipped with a calibration function, which enables you to adjust
the temperature registered by the heater. N.B! The room must have achieved a stable
temperature before any calibration.
Press 2 times and use + or - to set the actual temperature observed in the room. Con-
firm withor wait 15 seconds for automatic confirmation.
Resetting the heater
See figure 4 on separate illustration sheet
Turn off the heater‘s main switch. Press and hold (9 while you turn on the heater‘s main
switch.
Memory function
The heater remembers all the temperature settings and will automatically return to the
desired temperature after a power cut. Your day- and nighttime setbacks will however be
deleted after a power cut, and you will need to register the programs again.
Open window” function
The heater has an “open window” function that is activated instantly when it registers a
sudden drop in temperature with more than 2 degrees Celsius in 2 minutes. The heater will
automatically stop heating and FO will be visible in the display of the heater.
The heater will automatically start heating again after 10 minutes (the display switch from
FO to desired room temperature).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mill MB900DN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mill MB900DN in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mill MB900DN

Mill MB900DN Additional guide - English - 2 pages

Mill MB900DN Usermanual and installation guide - English - 15 pages

Mill MB900DN Usermanual and installation guide - German - 17 pages

Mill MB900DN Usermanual and installation guide - Dutch - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info