789537
8
Zoom out
Zoom in
Previous page
1/128
Next page
6millnorway.com
EN
B
Electronic Thermostat
1. Remove the pre-mounted screws on both legs before you insert them into thebrack-
ets, so that you get a stable foot.
2. Attach the legs to the brackets by tightening 2 screws into each bracket.
3. Remove the pre-mounted screws from the bottom of the heater and place the heater
gently on its head to mount the feet.
4. Two screws must be fastened on each foot bracket.
5. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED.
Instructions mechanical thermostat
Please see table on page 4 for which models that have mechanical thermostats
Control Panel
See figure 4 on separate illustration sheet
1. Thermostat: Adjust the desired heat settin
2. Output selector:
A
SG2000MEC
0: OFF
|: 750W
||: 1250W
|||: 2000W
WARNING: BE SURE THE FOOT IS FITTED CORRECTLY AND ACCORDING TO THE
INSTRUCTIONS BEFORE USING THE HEATER!
ATTENTION! This heater is only meant to be used as a supplementary heating source, and
must not be used without supervision
Usage mechanical thermostat
1. Set the output selector to the OFF position (0) and the thermostat to minimum. Plug
the heater into a grounded outlet.
2. Set the output selector to position |, || or |||. Turn the thermostat up to the maximum
position. When the desired room temperature has been reached, turn the thermostat
slowly down until you hear a click. The thermostat can now remain in this position
until a different room temperature is desired. As soon as the room emperature falls
below this level, the heater will automatically switch on again. When the room has
again reached the desired temperature, the heater will switch off again.
3. If you wish to change the room temperature, repeat the instructions in step 2.
4. The heater has an overheat protection that turns the device off if any parts become
extremely hot.
5. To switch the heater off, turn the output selector to the O position. If the heater will
be left unused for a longer period of time, pull out the plug.
B
CO2200MECMAX
0: OFF
|: 1000W
||: 1200W
|||: 2200W
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mill Instant Convection heater SG2000 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mill Instant Convection heater SG2000 series in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 1.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info