789502

Mill CUS1800MECBA Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
See figure 4 on separate illustration sheet
See figure 3 on separate illustration sheet
5
millheat.com
EN
Assembly
1. Remove the pre-mounted screws on both legs before you insert them into the
brackets, so that you get a stable foot.
2. Attach the legs to the brackets by tightening 2 screws into each bracket. Do not tighten
completely in order to fit the foot into the square tracks of the heater.
3. Place the heater gently on its head and use the supplied screws to mount
the feet.
4. Place the foot in the square tracks and fasten each foot bracket with two screws.
Wait to tighten the screws until all four screws have been fastened. You can now tighten
the screws attaching the legs and brackets.
5. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED.
Instructions
Control Panel
1. Thermostat: Adjust the desired heat setting
2. Output selector:
O: OFF
Fan (only fan, no heating)
I: 1200W
II: 1800W
WARNING! BE SURE THE FOOT IS FITTED CORRECTLY AND ACCORDING TO THE
INSTRUCTIONS BEFORE USING THE HEATER!
ATTENTION! This heater is only meant to be used as a supplementary heating
source, and must not be used without supervision
1. Set the output selector to the OFF position (O) and the thermostat to minimum. Plug the heater
into a grounded outlet.
2. Set the output selector to position for fan only (no heating).
3. Set the output selector to position I or II. Turn the thermostat up to the maximum position.
When the desired room temperature has been reached, turn the thermostat slowely down
until you hear a click. The thermostat can now remain in this position until a dierent room
temperature is desired. As soon as the room temperature falls below this level, the heater will
automatically switch on again. When the room has again reached the desired temperature,
the heater will switch o again.
4. lf you wish to change the room temperature, repeat the instructions in step 3.
5. The heater has on overheat protection that turns the device o if any parts become
extremely hot.
6. To switch the heater o, turn the output selector to the O position. lf the heater will be le
unused for a longer period of time, pull the plug.
Usage
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mill CUS1800MECBA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mill CUS1800MECBA in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info