773914
7
Zoom out
Zoom in
Previous page
1/20
Next page
5
millheat.com
EN
See figure 1 on separate illustration sheet
See figure 2 on separate illustration sheet
Resetting the heater
Assembly
See figure 3 on separate illustration sheet
Power indicator
A. Drill holes in the wall for holes 1 & 2. Then drill holes in the wall for the topmost holes
(holes 3 & 4 by using 6)
B. Insert the wall plugs into the drilled holes and attach the bracket with 4 screws
C. Place the heater on the lower lugs on the bracket, then hang the heater on the
upper lugs (li the heater slightly to align the heater with for the upper lugs). Screw
in the locking screws on the top of the bracket (clockwise)
If the heater uses power (for example, when it heats up), the power indicator is on.
(Can be done even if you are connected to WiFi)
See figure 4 on separate illustration sheet
Temperature calibration
It may occur deviation between the temperature registered by the heater and the
actual temperature in the room. This can be caused by several reasons, however, the
most common is that the heater is placed in a fair distance from where you usually
reside. When you set the temperature to for example 22 degrees, it is only natural that
you expect the same temperature where your sofa is placed for instance. However,
the temperature sensor is placed on the product itself, and therefore a deviation in
temperature may occur. To adjust this, all Mill heaters are equipped with a calibration
function, which enables you to adjust the temperature registered by the heater. N.B! The
room must have achieved a stable temperature before any calibration.
MILL STEEL MILL GLASS
A B
1. On/O
2. Wall bracket
3 Temperature sensor
4. Heat emission
5. Thermostat
6. Steel front
1. On/O
2. Wall bracket
3. Temperature sensor
4. Heat emission
5 Thermostat
6. Glass front
Press 2 times and use the wheel (+ or –) to set the actual temperature observed
in the room. Confirm with or wait 15 seconds for automatic confirmation.
ATTENTION! Horizontal placement only.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mill AV900Wifi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mill AV900Wifi in the language / languages: English as an attachment in your email.

The manual is 2.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Mill AV900Wifi

Mill AV900Wifi User Manual - German - 14 pages

Mill AV900Wifi User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info