Manual Miele t 224 (page 7 of 48) (English)

302188

Zoom out

Zoom in

1/48

Operating instructions

for vented tumble dryer

T 224

To avoid the risk of accidents

or damage to the machine

it is essential to read these

instructions before it is installed

and used for the first time.

M.-Nr. 06 465 680

Disposal of the packing

material

The transport and protective packing

has been selected from materials which

are environmentally friendly for disposal

and can normally be recycled.

Ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation!

Rather than just throwing these

materials away, please ensure they are

offered for recycling.

Disposal of your old appliance

Electrical and electronic appliances

often contain materials which, if

handled or disposed of incorrectly,

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your appliance.

Please do not therefore dispose of it

with your household waste.

Please dispose of it at your local

community waste collection / recycling

centre and ensure that it presents no

danger to children while being stored

for disposal.

It should be unplugged or disconnected

from the mains electricity supply by a

competent person. The plug must be

rendered useless and the cable cut off

directly behind it to prevent misuse.

See the "Warning and Safety" section of

this booklet for further details.

Energy saving tips

To avoid unnecessarily long drying

times and high consumption of energy:

–

Make sure that your laundry is

thoroughly spun before drying.

The higher the spin, the greater the

savings that can be made in energy

and time during drying.

– Load according to the optimum

amount of laundry recommended for

the programme being used (see

"Programme chart").

Underloading is uneconomical.

Overloading gives a poorer quality of

drying and may cause unnecessary

creasing.

–

Make sure the room in which the

dryer is located is well ventilated.

–

Make sure the fluff filter is clean

before using the dryer.

–

Check all parts of the ventilation

system on a regular basis and

remove any build up of fluff etc.

–

The vent ducting should be as short,

straight and smooth as possible to

minimise any resistance to the air

throughflow.

This helps to reduce running times

and energy consumption levels.

Caring for the environment

Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Care symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Low temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Changing the programme sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning the fluff filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Check and fault indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Contents

Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 25

Building under a continous worktop / in a kitchen run . . . . . . . . . . . . . . . . . . . 25

Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Installation - venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Calculating the effective duct length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installation to the left or right side of the machine . . . . . . . . . . . . . . . . . . . . . . . . . 30

Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

a Venting system with flexible ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

b Venting system with plastic piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

c Connecting directly to a wall vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Washer dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Altering the residual moisture level in the Cottons programmes. . . . . . . . . . . . . . 40

Altering the residual moisture level in the Minimum iron programmes . . . . . . . . . 41

Activating and deactivating the buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Changing the standard drying level in the Minimum iron - Normal programme . . 44

Changing the standard drying level in the Automatic programme . . . . . . . . . . . . 45

Contents

To avoid the risk of accidents and

damage to the machine please read

these instructions carefully before

using it for the first time. They

contain important information on its

safety, installation, use and

maintenance.

Keep these instructions in a safe

place and ensure that new users are

familiar with the content. Pass them

on to any future owner of the

machine.

Correct use

The tumble dryer is only intended

for drying fabrics which have been

washed in a water solution, marked on

the manufacturer's care label as being

suitable for tumble drying.

"Dry cleaning kits" for freshening up

garments in a tumble dryer are

increasingly available on the market. If

using, do so at your own risk, and

follow the instructions provided on the

packaging.

Any other applications may be

dangerous. The manufacturer is not

liable for damage resulting from

improper use or operation.

Technical safety

Before setting up the machine,

check it for any externally visible

damage.

Do not install or use a damaged

machine.

Before connecting the machine,

ensure that the connection data on

the data plate match the mains

electricity supply. If in any doubt,

consult a qualified electrician.

The electrical safety of this

machine can only be guaranteed

when continuity is complete between it

and an effective earthing system which

complies with local and national safety

regulations. It is most important that this

basic safety requirement is present and

regularly tested, and where there is any

doubt the household wiring system

should be inspected by a qualified

electrician. The manufacturer cannot be

held liable for the consequences of an

inadequate earthing system (e.g.

electric shock).

Do not connect the machine to the

mains electricity supply by an

extension lead. Extension leads do not

guarantee the required safety of the

appliance (e.g. danger of overheating).

Warning and Safety instructions

The machine is built in accordance

with current safety requirements.

Unauthorised repairs could result in

unforeseen dangers for the user, for

which the manufacturer cannot accept

liability. Repairs should only be

undertaken by a Miele approved

technician.

Ensure current is not supplied to the

machine until after maintenance or

repair work has been carried out.

Faulty components must only be

replaced by genuine Miele original

spare parts. Only when these parts are

fitted can the safety standards of the

machine be guaranteed.

If the connection cable is faulty it

must only be replaced by a Miele

approved service technician to protect

the user from danger.

In countries where there are areas

which may be subject to infestation

by cockroaches or other vermin, pay

particular attention to keeping the

machine and its surroundings in a

clean condition at all times. Any

damage which may be caused by

cockroaches or other vermin will not be

covered by the machine guarantee.

Warning and Safety instructions

In the event of a fault or for

cleaning purposes, the machine is

only completely isolated from the

electricity supply when:

–

it is switched off at the wall socket

and the plug is withdrawn, or

–

it is switched off at the mains, or

–

the mains fuse is withdrawn, or

–

the screw-out fuse is removed (in

countries where this is applicable).

Use

This equipment may only be used

in mobile installations such as

ships, caravans, aircraft etc. if a risk

assessment of the installation has been

carried out by a suitably qualified

engineer.

This dryer must not be:

– connected to a chimney or vent flue

which is in use.

–

used without exhaust ducting.

–

used without the fluff filter in place or

if the fluff filter is damaged in any

way.

Check all parts of the extraction

system on a regular basis (e.g. wall

vent, external grille, bends in the

ducting etc.) and make sure they are all

free of any hindrance. A build-up of fluff

will prevent a free-flow of air through the

system. If the dryer is to be connected

to an existing ducting system this must

be checked for suitability beforehand.

Adequate ventilation is essential to

avoid the danger of asphyxia and

toxic fumes where another appliance

which also uses the room air (e.g. gas,

oil or coal fired heater, continuous flow

or other water heater) is installed in the

same or an adjacent room.

To ensure safe operation, and to

prevent gases given off by these

appliances being drawn back into the

room, an underpressure of 0.04 mbar is

the maximum permissible.

–

Ventilation can be maintained by air

inlets which cannot be blocked, in

windows, doors and outside wall

vents, or by fitting a window contact

switch which ensures that the tumble

dryer can only be operated when the

window is opened wide enough.

If in doubt, the advice of a competent

builder, or for gas, a "Corgi" registered

installer (in the UK) must be sought.

The exhaust air must not be vented

into a chimney or vent flue which is

in use, nor should it be connnected to

ducting which ventilates rooms with

fireplaces. It would be dangerous if

smoke or exhaust fumes were drawn

back into the room.

Do not install the machine in a

room where there is a risk of frost

occurring. At temperatures around

freezing point the machine may not be

able to operate properly.

The ambient room temperature should

be between +2°C and +35°C.

Warning and Safety instructions

To prevent the risk of fire the

following textiles must not be

dried in this machine:

–

fabrics which contain a large

proportion of rubber, foam rubber or

rubber like materials.

–

items which contain damaged

padding or fillings (e.g. pillows,

jackets).

–

items which have been treated with

inflammable cleaning agents.

–

items which have been splashed with

hair lacquer, hair spray, nail varnish

remover or similar substances.

– items which have been soiled with

oils or residues containing grease

(kitchen oils, cosmetics etc.).

– items soiled with wax or other

chemicals (e.g. mops and floor

cloths).

– items which have not been

thoroughly cleaned and which are

still soiled with grease or oil, e.g.

workwear. Such clothing may require

a heavy duty detergent to get them

clean. If necessary consult the

detergent manufacturer for advice.

Do not let anyone sit or lean on the

door, as this can cause the

machine to tip up.

Always close the door after use.

This way you will avoid the danger

of:

–

children climbing onto or into the

dryer or hiding things in it.

–

pets or other small animals climbing

into it.

Safety with children

This machine is not a toy. To avoid

the risk of injury keep children

away from the machine at all times and

supervise them whilst you are using it.

Do not allow children to play on or near

it or to play with its controls. Supervise

its use by the elderly or infirm.

Using accessories

Accessory parts may only be fitted

when expressly approved by Miele.

If non-Miele parts are used with this

machine, guarantee, performance and

product liability claims may be

invalidated.

Disposal of your old machine

Before discarding an old machine,

switch it off at the wall socket and

unplug it. Render the plug useless and

cut off the cable directly behind the

machine. This should be done by a

competent person.

The manufacturer cannot be held

liable for damage caused by

non-compliance with these Warning

and Safety instructions.

Warning and Safety instructions

a Programme selector

The programme selector can be

turned clockwise or anti-clockwise.

b Programme sequence and check

lamps

c Start button

Press the

Start

button to start a

programme.

The

Start

indicator lamp will flash as

soon as a programme can be

started. It lights up constantly once

the programme has started.

d I-On/0-Off button

To switch the machine on or off / to

interrupt a programme.

The Anti-crease/Finish lamp will light

up as confirmation that the machine

has been switched on.

e Door Button

To open the door / to cancel a

programme.

Pressing this button will open the

door even when the machine is

switched off at the mains.

If the machine is switched on at the

mains and the door is opened the

drum lighting will come on. It will go

out a few minutes later to save

energy.

PC indicator light

The indicator light marked PC is used

by Miele Service technicians as an

optical interface.

Control panel

Care symbols

Before drying check the drying symbol

on the care label. If there are no

symbols, dry at your own risk!

q. . . . . . . . . Dry at normal temperature

r . . . . . . . . . . Dry at a low temperature

s . . . . . . . . . . . . . . . Do not tumble dry

–

For delicates and fabrics with the

following care label r select

Low

temperature

Tips on drying

– Always observe the maximum

recommended loads given in the

"Programme chart". Never overload

the drum.

Overloading can cause unnecessary

wear and tear to the laundry, give a

disappointing drying result and

cause more creasing.

– Do not put soaking wet items into the

tumble dryer. Spin them thoroughly

after washing using the appropriate

spin speed.

–

Use the

Automatic

programme for

drying mixed loads of cottons and

minimum iron fabrics.

–

Open jackets

so that they can dry

evenly.

–

Woollens and wool blends

tend to

become matted and shrink if dried in

a tumble dryer. They can, however,

be partially dried using the

Woollens

hand care

programme.

–

Down-filled garments

have linings

which have a tendency to shrink,

depending on the quality of the item.

They can be partially dried using the

Smoothing

programme.

–

Pure linen

should only be machine

dried if specified as suitable by the

manufacturer on the care label, as

the surface of the fabric may

otherwise become rough. They can

be partially dried using the

Smoothing

programme.

–

Loopknit garments

(e.g. T-shirts and

underwear) tend to shrink depending

on their quality. Do not over-dry these

textiles. When purchasing these

garments it is advisable to take their

shrinkage properties into account.

– Minimum iron fabrics

and 100%

cotton shirts or blouses tend to

crease more, the greater the load.

This is especially true of very fine

weaves.

Reduce the load or use the

Minimum

iron - Hand iron

programme.

–

Starched laundry

can be dried in the

tumble dryer. To achieve the usual

finish, double the amount of starch

should be used.

–

New dark coloured garments

should

be washed and dried separately

from light coloured garments to avoid

the danger of colours running and

discolouring other garments or even

plastic components in the machine.

Dark coloured fibres can also settle

on light coloured garments and vice

versa.

Notes on laundry care

Brief instructions

The headings numbered (A, B, C ...)

show the operating sequence and can

be used as a brief guide to using your

machine.

A Sort the laundry

To ensure an even drying result

separate out the washed laundry and

sort it according to: . .

. . . the drying level required

. . . the type of fibre or weave

. . size

. . the moisture content after spinning.

Make sure that objects e.g.

detergent dispensing balls have

been removed from the laundry.

They could melt, and cause damage

to the dryer or the laundry.

– Check seams and stitching to ensure

that padding and linings are intact.

– Fasten duvet covers and pillow

cases to prevent small items from

being trapped inside them.

–

Fasten hooks and eyes etc.

–

Tie fabric belts and apron strings.

–

Sew in or remove underwiring from

bras.

B Turn on the tumble dryer

Switch the dryer on by pressing the

I-On/0-Off

button in.

The tumble dryer may be switched on

after loading, saving energy as the light

will not come on.

C Load the tumble dryer

Press the

Door

button to open the

door.

Load the laundry loosely into the

drum.

Do not overload the drum. See the

"Programme chart" for

recommended loads for each

programme.

Overloading can cause unnecessary

wear and tear to the laundry and

give a disappointing drying result.

^ Before closing the door make sure

the fluff filter is correctly positioned.

Check the laundry is right inside the

drum so that it cannot get trapped or

damaged when the door is shut.

Shut the door either with a gentle

swing, or lean against it and push it

shut.

How to dry correctly

D Select a programme

^ Turn the programme selector to the

required programme.

Low temperature

^ For drying particularly sensitive

fabrics (care symbol r) e.g. acrylics

turn the programme selector to the

Low temperature

position.

Because the heater rating is reduced

for the

Low temperature

setting clothes

dry more slowly thus lengthening drying

times.

E Start the programme

Press the

Start

button.

The indicator lamp for the

Start

button

will then change from flashing to being

on constantly.

The drying cycle begins.

Depending on the programme

selected, the drying stage reached is

shown by the sequence indicator lamps

on the right hand side of the control

panel.

Before the end of a programme

The cooling down phase takes place

before the end of a programme so that

the garments are not too hot to handle

(the

Cool air

indicator lamp will come

on). The programme is not finished until

the cooling down phase is complete.

The

Woollens handcare

and

Smoothing

programmes do not include a cooling

down phase.

At the end of a programme

The

Anti-crease/Finish

indicator lamp

comes on.

The drum will continue to rotate at

intervals to prevent laundry creasing, if

you do not wish to remove it immediate

ly. The anti-crease phase lasts for an

hour. There is no anti-crease phase on

the

Woollens handcare

programme.

During the anti-crease phase . . .

. . . (depending on the programme

selected) the indicator lamp for the

drying stage reached will also light up.

. . . the buzzer will sound at intervals.

How to dry correctly

F Remove the laundry

Press the

Door

button.

Open the door.

Remove the laundry.

Make sure that the drum is empty. If

items are left in the dryer, they could

be damaged by overdrying when

the dryer is next used.

Switch the dryer off by pressing the

l-On/0-Off

button.

Clean the fluff filter in the door.

^ Close the door.

Changing the programme

sequence

Changing a programme while it is

running

As long as the cooling down phase or

the anti-crease phase has not been

reached, it is possible to change a

programme after it has started by

turning the programme selector to a

different programme position.

To interrupt a programme

Switch the machine off with the

I-On/0-Off

button.

To continue drying:

Switch the dryer on with the

I-On/0-Off

button.

The programme will continue (only with

the

Cottons, Minimum iron and Auto

matic

programmes).

Other programmes:

Press the

Start

button.

To cancel a programme

Turn the programme selector to

Finish

or open the door .

Adding or removing laundry after a

programme has started

Press the

Door

button.

Open the door.

Do not touch the back of the

drum when adding or removing

items. The drum could be very hot -

danger of burning.

^ Add or remove items.

^ Close the door.

^ Press the

Start

button.

How to dry correctly

Cottons Max. load: 6 kg*

Normal+, Normal**, Low temperature

Fabric

type

Single and multi-layered cottons fabrics such as towelling, jerseywear,

underwear, flannelette bed linen.

Note

–

Select

Low temperature

for fabrics with the r symbol. Laundry is

dried at a lower temperature.

Hand iron**, Machine iron

Fabric

type

Cottons and linen fabrics, e.g. table linen, bedlinen, starched laundry.

Note To prevent laundry from drying out it should be rolled up until you are

ready for ironing.

Minimum iron Max. load: 3 kg*

Normal**, Low temperature, Hand iron

Fabric

type

Minimum iron items made of cotton, synthetic or blended fabrics, e.g.

shirts, blouses, skirts and table cloths.

Notes – Select

Low temperature

for fabrics with the r symbol (e.g. acrylic

garments). Laundry is dried at a lower temperature.

– Select

Hand iron

for delicate fabrics and to reduce creasing even

more, reduce the load to 1.5 kg*.

– In the Miniumum iron

Hand iron

programme, items are dried with

very little creasing, depending on fabric type and amount of load.

* Weight of dry laundry

** Note for test institutes:

Programme setting for testing in accordance with EN 61121

Programme chart

Automatic Max. load: 3 kg*

Fabric

type

Mixed load of cotton and minimum iron fabrics.

Timed drying Max. load: 6 kg*

Warm air

Fabric

type

–

Multi-layered fabrics whose layers have different drying

characteristics, e.g. jackets, pillows.

–

For drying individual items, e.g. bath towels, bathing costumes,

tea-towels.

Cool air

Fabric

type

Any item which only needs airing.

Woollens handcare Max. load: 2 kg*

Fabric

type

Woollen fabrics

Notes – To refresh and fluff up woollen garments quickly. Woollen fabrics

are not dried completely by this programme.

– Remove garments as soon as the programme has finished and

leave to finish drying at room temperature.

Smoothing Max. load: 3 kg*

Fabric

type

– Cottons and linen fabrics.

– Minimum iron items made of mixed fibres, cottons or synthetics e.g.

trousers, jackets, shirts.

Notes

–

Smooths out creasing caused during the spin cycle in the washing

machine.

–

Fabrics are not completely dried in this programme. Remove

garments as soon as the programme has finished and leave to

finish drying at room temperature.

* Weight of dry laundry

Programme chart

Cleaning the fluff filter

The fluff which is created by the

drying process is collected in the fluff

filter in the door. Clean the filter after

every drying cycle.

^ Open the door and pull the fluff

filter (1) out of the door as illustrated.

Use your fingers to remove the fluff

from the surface of the filter.

Remove any fluff from the hollow part

of the door holder.

A cleaning brush is available as an

optional extra from your Miele dealer

or the Miele Spare Parts Department.

You can also use a vacuum cleaner.

Also clean the door seal (2) with a

damp cloth.

If there is a great deal of compacted

fluff on the filter, it can be cleaned

under running water.

^ After cleaning shake thoroughly until

no more water droplets are visible.

^ Dry the filter carefully.

^ Once clean, push the filter back into

the door holder until it clicks into

position. Ensure it is facing the

correct way. Close the door.

Cleaning and care

Tumble dryer

Disconnect the machine from the

power supply.

Clean the housing and control panel

with a mild cleaning agent or soapy

water.

Clean the drum and other stainless

steel parts with a suitable proprietary

stainless steel cleaner following the

manufacturer’s instructions.

Do not use solvents, abrasive

cleaners, glass cleaners or

all-purpose cleaners. These could

damage plastic surfaces and other

parts. The machine must never be

hosed down.

^ Dry all parts with a soft cloth.

E-Cloth

A microfibre "E-Cloth" is available from

the Miele UK Spare Parts Department,

which is suitable for cleaning surfaces

such as stainless steel, glass, plastic

and chrome without the use of

chemicals.

Cleaning and care

With the help of the following notes minor faults in the performance of the

machine, some of which may result from incorrect operation, can be put right

without contacting the Service Department.

Repair work to electrical appliances should only be carried out by a

suitably qualified person in strict accordance with local and national safety

regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

General problems

Problem Possible cause Remedy

The tumble dryer fails to

start when switched on.

No obvious cause.

–

Have you followed the

switch-on procedure

correctly (see “How to

dry correctly”)?

– Is the plug correctly

inserted in the socket

and switched on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

Items made of synthetic

fibres are charged with

static electricity after

drying.

Synthetic fibres tend to

attract static charge.

Static charge can be

reduced by adding a

fabric conditioner to the

final rinse in the washing

machine or a fabric

conditioner sheet to the

load in the dryer.

Problem solving guide

Problem Possible cause Remedy

There is a build

up of fluff.

Fluff is principally the result of

friction when garments are

being worn and washed.

Machine drying hardly

causes any fluff to form and

has been established by

research institutes to have no

appreciable effect on the

lifetime of the garment.

Fluff is collected by the fluff

filter and can be easily

removed (see "Cleaning and

Care").

The laundry is

not sufficiently

dry.

The load consisted of

different fabrics.

–

Finish drying using "Timed

drying - Warm air".

–

Select a more suitable

drying programme next

time (see "Programme

chart").

The interior drum

lighting does not

come on.

The lighting switches off

automatically (to save

energy).

Switch the dryer off and then

on again.

The lamp needs changing. Change the lamp as

described at the end of this

section.

Problem solving guide

Problem Possible cause Remedy

The drying

process goes on

too long or even

switches off.

Important: Before attempting to remedy one of the following

causes, switch the dryer off and switch on again to start the

programme again.

Ventilation to the dryer is

insufficient (e.g. because it

is installed in a room which

is too small).

Open a door or window while

the machine is in operation for

increased air flow.

The fluff filter may be

blocked.

Remove any fluff.

The vent ducting or the

ventilation outlet is blocked.

–

Check all parts of the

extraction system on a

regular basis (e.g. wall vent,

external grille, bends in the

ducting etc.) and make sure

they are all free of any

hindrance.

– Remove any fluff.

The laundry has not been

spun sufficiently.

Make sure that your laundry is

thoroughly spun at the

appropriate spin speed.

The tumble dryer has been

overloaded.

Do not exceed the maximum

load for the programme

selected.

Metallic components, e.g.

zips have prevented the

dryer from registering the

correct moisture level in the

laundry.

–

Close zips and fasten any

hooks next time.

If the problem occurs again,

dry garments with long zips

using "Timed drying - Warm

air".

Problem solving guide

Check and fault indicator lamps

Problem Possible cause Remedy

The programme has

stopped. The

Anti-crease/Finish

lamp has come on in

the sequence display

and the buzzer is

sounding.

This is not a fault.

The electronic unit has

recognised that there is no

laundry in the drum and

cancelled the programme.

Drying individual garments

or items which are already

dry can also cause the

programme to be stopped.

Use the "Timed drying -

Warm air" programme to

dry individual items.

Before changing a

programme: Open and

close the drum door.

The programme has

been interrupted. The

indicator lamp for

Hand iron or Machine

iron is flashing, and

the buzzer sounds.

No obvious cause.

–

Switch the dryer off and

then on again.

– Then start the

programme again.

If the programme stops

again and the fault

message reappears there

is a fault. Contact the

Miele Service

Department.

Problem solving guide

Changing the lamp

Disconnect the machine from the

mains electricity supply.

Open the door.

You will find the interior lamp cover at

the top of the drum aperture.

^ Insert a suitable tool, such as a wide

bladed screwdriver, under the side

edge of the lamp cover as illustrated.

Apply a little pressure and whilst

doing so turn your wrist in the

direction of the arrow to open the

cover.

The cover will open downwards.

The temperature resistant lamp should

only be ordered from your Miele dealer

or the Miele Spare Parts Department.

The lamp specification and

maximum wattage is stated on the

data plate and on the lamp cover.

Replace the lamp.

To close the cover push it upwards

and press it on the left and right until

you hear it click into position.

Ensure that it is fitted into

position securely, as any moisture

could cause a short circuit.

Problem solving guide

Repairs

In the event of any faults which you

cannot remedy yourself, or if the

machine is under guarantee, please

contact

–

your Miele dealer, or

–

the Miele Service Department

(see back cover for contact details).

When contacting your Dealer or the

Service Department, please quote the

model and serial number of your

machine, both of which are shown on

the data plate situated on the right

hand side below the drum aperture.

Appliance guarantee

Please see the guarantee card

supplied with your machine.

Optional accessories

Optional accessories for this dryer is

available from your Miele Dealer or from

the Miele Spare Parts Department.

Please note that telephone calls may

be monitored and recorded to

improve our service.

After sales service

Front view

a Venting connection: rear, right or left

(supplied with the rear socket open)

b Mains connection cable

c Control panel

d Door

e Four height adjustable screw feet

Installation and connection

Installation site

Make sure the dryer door can be

opened without hindrance after

installation.

Transporting the machine to its

installation site

When moving the machine you can

hold it by the lid where it protrudes to

the rear of the dryer. To manoeuvre the

dryer out of its packing case to its

installation site you will also need to

hold it by the front feet.

Building under a continous worktop /

in a kitchen run

The space required by the vent duct

must be taken into consideration when

calculating the distance between the

machine and a wall or other appliances

or furniture on either side.

A building under kit* is required

which must be fitted by a suitably

qualified person.

The machine lid is replaced by a

coverplate.

It must be fitted by suitably qualified

person to ensure electrical safety.

The building-under kit is supplied with

its own installation instructions.

N.B. When built under drying times may

be longer.

–

The electrical socket must be

located in an accessible position

near the machine.

With niche heights of:

–

840 mm, longer screw feet* are

required.

–

870/885 mm - 915/930 mm, one or

two height adjustment frames* are

required.

* Available as an optional accessory

from your Miele dealer or the Miele

Spare Parts Department.

If you wish to push your machine under

a worktop and there is space to do this

without removing the lid, the building

under kit is not necessary. Otherwise

the building under kit is essential.

Replacing the lid

If the lid has been removed in order to

fit a coverplate, ensure that, if the lid is

ever replaced, it fits securely into the

rear holders. Otherwise, it is not

properly secure for transport.

Installation and connection

Levelling the machine

The machine must be perfectly level to

ensure safe and proper operation.

The screw feet can be adjusted to

compensate for any unevenness in

the floor.

A ventilation gap of 10 mm must

be maintained between the base of

the machine and the floor. It must

not be blocked by deep pile

carpets, plinths, etc as this would

prevent a sufficient intake of air.

Washer-dryer stack

The tumble dryer can also be

combined with a Miele washing

machine in a washer-dryer stack. To do

this the appropriate stacking kit* (WTV)

to match your washing machine is

required.

* Available as an optional accessory

from your Miele dealer or the Miele

Spare Parts Department.

,Stacking kits must only be

installed by a suitably qualified fitter.

Installation and connection

Electrical connection U.K.

All electrical work should be carried out

by a suitably qualified and competent

person, in strict accordance with

current national and local safety

regulations (BS 7671 in the UK).

Ensure power is not supplied to the

appliance until after installation work

has been carried out.

The appliance is supplied with a mains

cable with moulded plug ready for

connection to a 230-240V mains

supply. Please ensure the connection

data quoted on the data plate match

the household mains supply.

Connection should be made via a

suitable switched socket which is easily

accessible after installation.

For extra safety it is advisable to install

a residual current device (RCD), with a

trip current of 30 mA (in accordance

with DIN VDE 0664, VDE 0100 Section

739).

Do not connect via an extension lead.

Extension leads do not guarantee the

required safety of the appliance (e.g.

danger of overheating).

Non-rewireable plugs BS 1363

The fuse cover must be refitted when

changing the fuse, and if the fuse cover

is lost, the plug must not be used until a

suitable replacement is obtained. The

colour of the correct replacement cover

is that of the coloured insert in the base

of the plug, or the colour that is

embossed in words on the base of the

plug (as applicable to the design of

plug fitted).

Replacement fuses should be ASTA

approved to BS 1362 and have the

correct rating. Replacement fuses and

fuse covers may be purchased from

your local electrical supplier.

WARNING: THIS APPLIANCE

MUST BE EARTHED

Electrical connection

General

Important

Before operating the tumble dryer, a

suitable ducting system must be

installed to carry the moist air from

the dryer to the outside. This can be:

. . . flexible ducting hose, or plastic

piping connected to the dryer, or

. . . the dryer may be connected

directly to the wall vent.

–

Before installing the ducting system,

ensure that the machine is not

connected to the power supply.

– The ducting outlet (e.g. wall pipe)

should be installed in such a way

that the moist expelled air . . .

. . . cannot be drawn back into the

room in which the dryer is installed;

. . . cannot cause any damage to the

building or other nuisance.

– The dryer uses the room air. It is

therefore essential to ensure

adequate ventilation to avoid the

danger of asphyxia caused by gases

given off by other appliances being

drawn back into the room.

Insufficient ventilation will also cause

drying times to be considerably

longer.

Ventilation can be maintained by:

- an open window;

- an air inlet which cannot be

blocked in windows, doors and

outside wall vents;

- a window switch which prevents

the dryer being used when the

window is closed.

Avoid:

–

very long ducting systems

–

too many bends or corners, tight

corners

Otherwise the drying result will be less

effective and it will take longer and use

more energy.

Suitable materials

–

for the ventilation ducting:

flexible ducting* or plastic piping

with a diameter of at least 100 mm.

– for venting to the outside:

a wall pipe kit* or a window vent kit*.

* Available as an optional accessory

from your Miele dealer or the Miele

Spare Parts Department.

Procedure

^ First measure the duct length

required. Calculate the effective duct

length and establish the internal duct

diameter required (use the tables on

the next page).

Then decide which type of ducting

you want to use (see "Venting

systems" in this section).

Installation - venting

Calculating the effective duct

length:

Friction against the inner walls of the

ducting will slow down the expelled air

as it passes through. An elbow, bend,

non-return flap or wall vent creates

more friction than a straight duct. The

friction created by each of these is

expressed as an additional duct

length factor. The additional length

factors are calculated by comparing

the friction created by, for example, an

elbow to that created by 1 metre of

straight plastic piping (Table I).

The additional duct length factor for

each item needs to be added together

to ascertain the effective duct length

required.

A larger internal duct diameter also

helps reduce friction. If the effective

duct length is more than 20 m the

duct diameter should be increased

(Table II).

1. To calculate the effective duct

length required:

First measure the distance which will

require straight ducting

. Multiply this

amount by the corresponding

additional duct length factor in Table I.

Establish the number of angles,

bends etc. necessary and add their

additional duct length factors

together with the help of Table I.

Add all the additional duct length

factors together to get the effective

duct length.

2. Internal duct diameter

Refer to Table II for the appropriate

duct diameter required.

Table I

Additional

duct length

factor

Flexible ducting*

–

1 m laid straight

–

45° angle

(Bend radius = 0.25 m)

–

90° angle

(Bend radius = 0.25 m)

1.8 m

1.5 m

2.5 m

Flexible aluminium ducting* / plastic

piping

–

1 m laid straight / or 1 m straight

pipe

–

45° angle / elbow

(Bend radius = 0.25 m)

–

90° angle / elbow

(Bend radius = 0.25 m)

1.0 m

0.6 m

0.8 m

Wall vent kit* or window vent kit*

–

with louvred grille

–

with non-return flap (hinged flap)

3.8 m

1.5 m

Non-return flap* to be integrated into

the vent ducting

14.3 m

Flat ducting (for washer dryer

stack)*

11.0 m

Venting connection to the left/right 1.0 m

* optional accessory from Miele

Table II

Maximum effective

duct length allowable

Internal duct

diameter

required

10 m with

Ring adapter

20 m without

Ring adapter

40 m without

Ring adapter

100 m without

Ring adapter

100 mm

125 mm

150 mm

Installation - venting

3. Example

A Wall pipe, with louvred vent

= 1 x 3.8 m Additional duct

length

= 3.8 m

B/D 2 Elbows, 90°

= 2 x 0.8 m Additional duct

length

= 1.6 m

C 0.5 m plastic piping

= 0.5 x 1 m Additional duct

length

= 0.5 m

E Side connection, left

= 1 m Additional duct length = 1.0 m

Effective duct length = 6.9 m

Result: A duct diameter of 100 mm is

adequate as the effective duct length is

less than the 20 m specified in Table II.

Installation to the left or right

side of the machine

At the rear

The connection is opened at the

factory.

Fit one of the venting systems

described on the following pages.

Left or right side of the machine

Remove the left or right hand side

cover cap. Do not remove the frame.

Refit it in the rear outlet.

Ensure it is securely in position so

that it cannot fall out when the dryer

is in operation.

Fit one of the venting systems

described on the following pages.

Installation - venting

Venting systems overview

The various venting systems which are

possible (a b c) are described on

the following pages.

Adapter

A ring adapter** (1) is installed in

adapter (2) for the installation of a

flexible vent duct. It reduces time and

energy requirements during drying

when used in combination with a short

vent duct (maximum 10 m total

length). The ring adapter is removable

and designed for use with all venting

systems.

** Note for test institutes: EN 61121 Standard

testing is carried out with the ring adapter.

a Venting system with flexible

ducting

This is a simple, cost effective

method of directing the moist air

outside. The adapter is fitted into the

vent opening on the dryer and the

ducting hose is then connected to

the adapter.

The following items are required:

... flexible ducting hose

... a wall vent kit* or window vent kit*.

* (Miele optional accessory).

Ring adapter (1) must be taken out of

adapter (2), if the total duct length is

longer than 10 m.

If the total duct length is less than 10

m the ring adapter should be left in

the adapter.

Fit adapter (2) into the vent opening

on the dryer, and connect vent hose

(3).

See next page for examples.

Installation - venting

Installation examples

Window vent

1. Window vent kit (fitted in a

"plexiglass" pane)

(separate fitting instructions are

supplied with the Miele window vent

kit)

2. Adapter for flexible hose

Connection to an exhaust flue

1. Pipe with connection piece

(= supplied with the Miele wall vent

kit)

2. Adapter for flexible hose

3. Exhaust flue insulated against damp

The ducting must not be vented

into a chimney or vent flue which is

in use, nor should it be connected to

ducting which ventilates rooms with

fireplaces.

Installation - venting

b Venting system with

plastic piping

Plastic piping is a good option where

the vented air has to ducted for some

distance. The smooth walls of the

pipe are less resistant to the vented

air than the walls of a flexible vent

hose, for example. Time and energy

consumption are better with plastic

piping.

The following items are required: . .

. . . an adapter* (dia. 100 mm)* with

rib on the inside.

. . . a wall vent kit* or window vent

kit*.

* (Miele optional accessory)

. . . Suitable plastic piping is

available from your dealer or builder’s

merchant. If a pipe diameter greater

than 100 mm is required, additional

adapters are necessary (e.g. to

increase from C 100 to 125 mm) to

connect the pipe to the dryer.

A The ring adapter (1) only needs to be

fitted into the Miele adapter (2), if the

total duct length is less than 10 m.

If the total duct length is greater than

10 m the ring adapter is not required.

B Fit Miele adapter (2) into the vent

opening on the dryer.

C Attach the pipe (3).

Example

1. Wall vent kit

(Separate fitting instructions are

supplied with the Miele wall vent kit).

2. Adapter

3. Plastic piping, diameter DN 100

Installation - venting

c Connecting directly to a wall

vent

The best method of venting the dryer

is to connect it directly to the outside

wall of a room. However, it is

necessary to insert the wall vent right

through the wall.

Because the vented air is blown

directly outside, and has only a short

distance to go, this system is very

efficient in terms of time and energy

consumption.

A wall pipe and a flexible foam

gasket must be used (both Miele

optional accessories).

A Before drilling into the wall . . .

. . . please read the installation

instructions supplied with the Miele

wall pipe.

. . . and study the following

diagrams.

View from above:

1. Wall pipe

2. Flexible foam gasket

Side view:

1. Wall pipe

2. Flexible foam gasket

B Insert the ring adapter (1) into the

wall pipe.

C Fit the foam gasket (3) on to the

connecting piece (2) on the wall pipe

and push the dryer up against the

wall.

Installation - venting

Washer dryer stack

Height of venting outlet for washer

dryer stack

Miele washing machine with straight or

sloping fascia

Stacking kit* without pull-out shelf:

A = 94.2 cm

B = 170.0 cm

Stacking kit* with pull-out shelf:

A = 92.8 cm

B = 168.6 cm

* Miele optional accessories

Miele washing machine with Comfort

line angled fascia

Stacking kit* without pull-out shelf:

C = 94.2 cm

D = 170.0 cm

Stacking kit* with pull-out shelf:

C = 96.0 cm

D = 171.8 cm

* Miele optional accessories

Installation - venting

Programme Load Final spin speed

in a domestic washing machine

Energy Time

kg* rpm kWh Minutes

Cottons Normal 6.0 800 (70 % residual moisture)**

1200

1400

1600

1800

3.90

3.05

2.90

2.80

2.55

107

Cottons Hand iron 6.0 800 (70 % residual moisture)**

1200

1400

1600

1800

3.00

2.20

2.05

1.95

1.70

Minimum iron Normal 3.0 1000 (50 % residual moisture)** 1.35 38

Minimum iron Hand iron 3.0 1000 1.20 33

Automatic 3.0 900 1.75 49

Woollens handcare 2.0 - 0.15 3

Smoothing 3.0 - 0.30 8

* Weight of dry laundry

** EN 61121 Standard testing is carried out with the ring adapter.

All data established in accordance with EN 61121.

Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual

moisture as per the above standard using the Cottons Normal programme.

Consumption data can vary from the nominal values given above depending on the size of the

load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity

supply and any additional options selected.

Consumption data

Height 850 mm (adjustable +7 / -7 mm)

Height for building under 820 mm

Width 595 mm

Depth 580 mm

Depth with door open 1,060 mm

Weight 48 kg

Drum volume 100 litres

Maximum capacity 6 kg dry weight

Length of connection cable 2 m

Voltage see data plate

Connected load see data plate

Fuse rating (UK) see plug

Lamp wattage see data plate

Energy consumption see "Consumption data" section

Test certificates awarded Radio / TV suppression, VDE

Technical data

Programmable functions

for changing default settings

The programmable functions are

used to alter the machine's

electronics to suit changing

requirements.

Programmable functions can be

altered at any time.

Altering the residual moisture

level in the Cottons

programmes

The machine is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier, it is possible to reduce the

default residual moisture level in the

Cottons programmes.

Please note that programme

durations will be longer if this option

is activated.

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to the

Cottons Normal

position.

F Pressing the

Start

button switches

between activating and deactivating

the drier setting.

– If the

Drying

indicator lamp is

flashing: the drier setting is

activated

– If the

Drying

indicator lamp is not

flashing, the drier setting is not

activated and the residual moisture

level is on the standard default

setting.

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the drier setting has been selected.

Switch off the dryer.

The check is complete.

Programmable functions

Altering the residual moisture

level in the Minimum iron

programmes

The machine is designed to dry

effectively using as little energy as

possible.

However, if you require the laundry to

be drier, it is possible to reduce the

default residual moisture level in the

Minimum iron programmes.

Please note that programme

durations will be longer if this option

is activated.

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to the

Cottons Low temperature

position.

F Pressing the

Start

button switches

between activating and deactivating

the drier setting.

– If the

Drying

indicator lamp is

flashing, the drier setting is

activated

– If the

Drying

indicator lamp is not

flashing, the drier setting is not

activated and the residual moisture

level is on the standard default

setting.

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the drier setting has been selected.

Switch off the dryer.

The check is complete.

Programmable functions

Activating and deactivating the

buzzer

A buzzer sounds (at intervals for a

maximum of 1 hr) to let you know the

programme has finished.

The machine is delivered with the

buzzer activated but you can

deactivate it if wished.

The buzzer will still sound if there is a

fault, even if it has been deactivated.

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to the

Cottons Hand iron

position.

F Pressing the

Start

button switches

between activating and deactivating

the buzzer.

– If the

Drying

indicator lamp is not

flashing:

the buzzer is deactivated

– If the

Drying

indicator lamp is

flashing:

the buzzer is activated

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the buzzer is activated.

Switch off the dryer.

The check is complete.

Programmable functions

Extending the cooling down

time

The cooling down phase which takes

place before the end of a programme

can be lengthened if required. This

makes the garments easier to

handle.

The dryer is delivered with the

extended cooling down time option

deactivated. You can extend the

cooling down time by 5 minutes or 10

minutes.

The option of extending the cooling

down time is available with the

Cottons,

Minimum iron and Automatic

programmes.

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

–

The door is closed.

–

The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to the

Cottons Machine iron

position.

F Pressing the

Start

button alters the

cooling down time.

–

If the

Drying

indicator lamp flashes

once:

The cooling down time will be five

miinutes longer.

–

If the

Drying

indicator lamp flashes

twice:

The cooling down time will be ten

minutes longer.

–

If the

Drying

indicator lamp is not

flashing:

The cooling down time is not

extended.

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

^ Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the cooling down time has been

extended.

Switch off the dryer.

The check is complete.

Programmable functions

Changing the standard drying

level in the Minimum iron -

Normal programme

The drying level for this programme

is set at a standard level.

You have the option of changing this

to an increased drying level.

The machine is delivered with the

drying level set at

Normal

You can change this to

Normal+

(drier

than the standard drying level).

Important: the "Normal+" drying level

will work in addition to the "Altering the

residual moisture level in the

Minimum

iron programmes

" programmable

function, if you have already set this.

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

–

The tumble dryer is switched off.

–

The door is closed.

–

The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to

Minimum iron - Normal

F Pressing the

Start

button alters the

drying level.

–

If the

Drying

indicator lamp is

flashing:

the standard drying level is

Normal+

–

If the

Drying

indicator lamp is not

flashing, the increased drying level

is not activated and the drying level

will remain on the standard setting

(

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

^ Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the Normal+ drying level has been

set.

Switch off the dryer.

The check is complete.

Programmable functions

Changing the standard drying

level in the Automatic

programme

The drying level for this programme

is set at a standard level.

You have the option of changing this

to an increased drying level.

The machine is delivered with the

drying level set at

Normal

You can change this to

Hand iron

(damper) or

Normal+

(drier than the

standard drying level).

Follow steps A to G to programme

and store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at

Finish

A Press the

Start

button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on with the

I-On/0-Off

button.

C Wait until the

Start

indicator lamp

comes on . . .

D . . . and then release the

Start

button.

E Turn the programme selector to the

Automatic

position.

F Pressing the

Start

button alters the

drying level.

–

If the

Drying

indicator lamp flashes

twice:

the standard drying level is

Normal+

–

If the

Drying

indicator lamp is not

flashing:

the standard drying level is Hand

iron

–

If the

Drying

indicator lamp flashes

once, the drying level has not been

changed and will remain on the stan

dard setting (

G Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now

stored in memory. You can change it

again at any time.

To check:

^ Make sure the dryer is switched off,

the door is closed and the

programme selector is at Finish and

then carry out steps A to E.

The

Drying

indicator lamp will show you

if the drying level has been changed.

Switch off the dryer.

The check is complete.

Programmable functions

Alteration rights reserved/1306

M.-Nr. 06 465 680 / 01

en-GB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Miele t 224 in the language / languages: English as an attachment in your email.

The manual is 0,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Miele t 224 Manual

Product: