581212
22
Zoom out
Zoom in
Previous page
1/54
Next page
Electrical connection
The electrical components of this dryer comply with
IEC 335-1 and IEC 335-2-11.
The electrical connection may only be carried out by
a suitably qualified technician in accordance with
local and national safety regulations (BS 7671 in the
UK).
Please observe the wiring diagram supplied.
Please ensure that the voltage and frequency of the
dryer as quoted on the data plate comply with the
on-site supply.
Connection should be made via a suitable isolator
which complies with local and national safety
regulations and which is easily accesible for
disconnecting the dryer from the electricity supply.
Provision must be made on site to switch off all poles.
Switches with a minimum all-pole contact gap greater
than 3 mm are suitable for isolating the appliance.
These include circuit breakers, fuses and relays
(IEC/EN 60947).
If the appliance is disconnected from the electricity
supply ensure adequate measures are taken to
ensure that the appliance cannot be reconnected to
the electricity supply until all work has been carried
out.
After the dryer has been connected to the electricity
supply check the phase rotation on the incoming
power supply to the appliance.
Equipotential bonding
Equipotential bonding must be carried out if required.
Air inlet and exhaust connection
This dryer must only be used when it is connected to
a suitable ducting system. The installation site must
be adequately ventilated. See the installation
instructions supplied.
Gas connection
This work must be carried out by an authorised
person in accordance with local and national safety
regulations. This must be a Gas Safe registered
technician in the UK. See the installation instructions
supplied.
,
The earth lead (N) and phase conductor (L)
must be connected to the correct connectors.
Take care not to connect them the wrong way
round!
The gas group to which the dryer has been set at the
factory is given on the Gas Data label on the rear of
the dryer.
If the appliance is converted for a different gas
group, or to liquid gas, a conversion kit is required.
This is available from the the Miele Spare Parts
Department. When ordering please quote the model
and serial number of the appliance, as well as the
gas type, group and connection pressure in the
country of installation.
Please follow the installation instructions carefully. To
ensure safety, any conversion work must only be
carried out by an authorised technician, e.g. Gas
Safe registered in the UK.
,
Do not attempt to repair or work on gas-heated
appliances yourself. Repairs must only be carried
out by an authorised technician to ensure safety.
In the event of a fault please contact the Miele
Service Department.
,
After setting up and connecting the appliance,
ensure that all outer casing parts are correctly
fitted back into position.
Installation and connection
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Miele PT 8303 SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Miele PT 8303 SL in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info