Manual Miele PT 5135C (page 64 of 64) (English)

70579

Zoom out

Zoom in

1/64

Operating and installation instructions

for condenser tumble dryer

PT 5135 C OS

To avoid the risk of accidents or

damage to the machine it is

essential to read these instructions

before it is installed, commissioned and

used for the first time.

M.-Nr. 09 869 880

en - EXP

Disposal of the packing

material

The transport and protective packing

has been selected from materials which

are environmentally friendly for disposal

and should be recycled.

Ensure that any plastic wrappings,

bags, etc are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation.

Disposal of your old machine

Electrical and electronic machines

often contain materials which, if

handled or disposed of incorrectly

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your machine.

Please do not therefore dispose it with

your household waste.

Please dispose of it at your local

community waste recycling centre or

contact your dealer for advice. Ensure

that it presents no danger to children

while being stored for disposal.

Energy saving tips

To avoid unnecessarily long drying

times and high consumption of energy:

–

Make sure that your laundry is

thoroughly spun before drying.

The higher the spin, the greater the

savings that can be made in energy

and time during drying.

–

Load according to the optimum

amount of laundry recommended for

the programme being used.

Underloading is uneconomical.

Overloading gives a poorer quality of

drying and may cause unnecessary

creasing.

– Make sure the room in which the

dryer is located is well ventilated.

– After every cycle remove the fluff

from the fluff filter in the door and in

the door opening (see "Cleaning and

Care").

– Check the condenser unit from time

to time and clean it when necessary.

Caring for the environment

Caring for the environment..........................................2

Warning and Safety instructions .....................................6

Operating the tumble dryer.........................................17

Control panel .....................................................17

Before using for the first time.........................................17

Display ..........................................................18

Before using for the first time.......................................19

Notes and tips on laundry care .....................................20

1. Sort the laundry .................................................20

2. Load the tumble dryer ............................................21

3. Select a programme .............................................21

Short instructions ................................................22

Delay start.......................................................26

Programme chart .................................................27

Basic programmes ................................................27

Special programmes ...............................................29

Changing the programme sequence .................................33

Payment system...................................................33

Changing a programme once it has started .............................33

Cancelling the current programme ....................................33

Adding or removing laundry after a programme has started ................33

Power cuts .......................................................33

Time remaining ...................................................33

Cleaning and care ................................................34

Cleaning the fluff filters .............................................34

Cleaning them whilst dry .........................................34

Cleaning them with water .........................................35

Replacing the filters .............................................35

Contents

Cleaning the tumble dryer ...........................................36

Cleaning the heat exchanger ........................................37

Removing the heat exchanger .....................................37

Checking the condenser unit (heat exchanger unit) ....................38

To clean the condenser unit .......................................38

Replacing the condenser unit......................................39

Problem solving guide ............................................40

Problem solving guide ..............................................40

Fault messages in the display ........................................40

An unsatisfactory drying result .......................................42

Other problems ...................................................43

Changing the lamp ................................................46

After sales service ................................................47

Repairs..........................................................47

PC / Optical interface...............................................47

Optional accessories ...............................................47

Installation and connection ........................................48

Front view .....................................................48

Side view......................................................49

Rear view .....................................................49

View from above ................................................49

Washer-dryer stack..............................................49

Installing the tumble dryer ...........................................50

Transporting the dryer to its installation site ...........................50

Levelling the machine............................................50

Room in which the dryer is located .................................51

Securing the tumble dryer against slippage ..........................51

Payment system ................................................51

External drainage of the condensed water ..............................52

Electrical connection ...............................................53

Contents

Technical data ...................................................54

Settings menu ...................................................56

Opening the Settings menu via the Supervisor level.......................56

Language J ......................................................57

Supervisor level ...................................................57

Anti-crease.......................................................58

Buzzer ..........................................................58

Time of day ......................................................58

Display contrast ...................................................58

Display brightness .................................................58

Standby .........................................................59

Extended cool down ...............................................59

Drying levels .....................................................59

Cottons .......................................................59

Minimum iron ..................................................59

Machine iron ...................................................59

Clean out airways .................................................60

Clean condenser unit...............................................60

Delay start .......................................................61

Contents

It is essential to read these instructions.

This tumble dryer complies with current safety requirements.

Inappropriate use can, however, lead to personal injury and

damage to property.

To avoid the risk of accidents and damage to the tumble dryer,

please read these instructions carefully before using it for the first

time. They contain important information on its safety, installation,

use and maintenance.

Keep these instructions in a safe place and ensure that they are

made available to new users. They must be made aware of these

Warning and Safety instructions.

Pass these instructions on to any future users/owners.

Correct application

This tumble dryer is only intended for drying fabrics which have

been washed in a water solution, and marked on the manufacturer's

care label as being suitable for tumble drying.

If using dry cleaning kits, do so at your own risk, and follow the

instructions provided on the packaging.

Any other applications may be dangerous. Miele cannot be held

liable for damage resulting from incorrect or improper use or

operation.

The tumble dryer is not intended for outdoor use.

Warning and Safety instructions

The tumble dryer can only be used by people with reduced

physical, sensory or mental capabilities, or lack of experience or

knowledge, if they are are supervised whilst using it or have been

shown how to use it in a safe way and recognise and understand the

consequences of incorrect use.

Children under 8 years of age must be kept away from the tumble

dryer unless they are constantly supervised.

Children 8 years and older may only use the tumble dryer

unsupervised if they have been shown how to use it in a safe way

and recognise and understand the consequences of incorrect

operation.

Children must not be allowed to clean or maintain the tumble

dryer unsupervised.

Please supervise children in the vicinity of the tumble dryer and

do not let them play with it.

Technical safety

Before setting up the tumble dryer, check it for any externally

visible damage.

Do not install or use a damaged tumble dryer.

Do not make any alterations to the tumble dryer, unless

authorised to do so by Miele.

Do not connect the tumble dryer to the mains electricity supply by

an extension lead. Extension leads are a fire hazard and do not

guarantee the required safety of the tumble dryer.

Warning and Safety instructions

The tumble dryer may only be operated when the following

conditions are met:

–

the list of the vessel is not more than 2°.

–

any external vibration is no more than 150 Hz at an amplitude of

0.35 mm.

The safe operation and correct functioning of the tumble dryer can

only be guaranteed if the above conditions are met.

The tumble dryer may not be operated on an open deck.

Appliances not marked with the CSA C/US Safety Label comply with

European safety regulations. These tumble dryers must not be

operated in the USA.

A risk assessment of the installation must be carried out by a

suitably qualified engineer before this appliance is installed or used.

Installation must only be carried out by a suitably qualified engineer.

The tumble dryer must be fixed in position when it is installed.

Failure to do this could result in personal injury and damage to

property.

Warning and Safety instructions

–

the ship’s hull is longer than 28 metres.

The electrical safety of this tumble dryer can only be guaranteed

when correctly earthed. It is essential that this standard safety

requirement is met. If in any doubt, please have the electrical

installation tested by a qualified electrician. Miele cannot be held

liable for the consequences of an inadequate earthing system (e.g.

electric shock).

Unauthorised repairs could result in unforeseen dangers for the

user, for which Miele cannot accept liability. Repairs should only be

undertaken by a Miele authorised service technician, otherwise any

subsequent damage will not be covered by the guarantee. Ensure

current is not supplied to the tumble dryer until after maintenance or

repair work has been carried out.

Faulty components must only be replaced by genuine Miele

original spare parts. Only when these parts are fitted can the safety

standards of the tumble dryer be guaranteed.

To ensure the correct performance of the tumble dryer and to

prevent the risk of faults and fire, it is important to check it and carry

out maintenance on a regular basis.

The tumble dryer must be isolated from the electricity supply in

the event of a fault and during cleaning and maintenance.

Please also read the "Installation and connection" and the "Electrical

connection" sections.

Warning and Safety instructions

Please observe the instructions in "Installation and connection"

and "Technical data".

The socket must be easily accessible after installation in order to

disconnect the tumble dryer from the electricity supply.

For hard-wired machines, the all-pole isolator provided on-site

must be easily accessible after installation in order to disconnect the

tumble dryer from the electricity supply.

Do not block the gap between the base of the dryer and the floor

with plinth facings, deep pile carpet etc. as this would hinder a

sufficient intake of air.

Make sure the dryer door can be opened without hindrance after

installation.

In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the tumble dryer

and its surroundings in a clean condition at all times. Any damage

which may be caused by cockroaches or other vermin will not be

covered by the appliance guarantee.

Warning and Safety instructions

Correct use

The maximum load of dry laundry for this tumble dryer is 6,5 kg.

See the Programme chart for the maximum recommended loads in

individual programmes.

Do not let anyone sit or lean on the door, as this can cause the

tumble dryer to tip up. Danger of injury.

Always close the door after use. This way you will avoid the

danger of:

–

children climbing into the dryer or hiding things in it.

– pets or other small animals climbing into it.

Do not use a pressure washer or hose to clean the tumble dryer.

Always keep the area around the tumble dryer free of dust and

fluff. Dust and dirt drawn into the tumble dryer can cause blockages.

Faults can then occur as well as the risk of fire.

Warning and Safety instructions

The dryer must not be used without the fluff filters in place or if

the fluff filters are damaged in any way. Damaged filters can cause

operational faults and blockages in the airways, condenser unit and

heating elements. Fire hazard.

In the event of a damaged filter, switch the dryer off and replace the

filter with a new one.

The fluff filters must be cleaned regularly.

The dryer must not be used without the condenser unit in place.

The fluff filters must be thoroughly dried after cleaning. Damp or

wet filters could cause operational faults.

Do not install the tumble dryer in a room where there is a risk of

frost occurring. At temperatures around freezing point the tumble

dryer may not be able to operate properly.

There is a risk of damage if the condensed water is allowed to

freeze in the pump and hoses.

The ambient room temperature should be between +2°C and

+35°C.

If the water is drained externally instead of being collected in the

condensed water container, make sure the drain hose is securely

attached if you hang it in a sink or basin to avoid the hose slipping

and the water causing damage.

Condensed water is not drinking water.

It can cause health problems in both people and animals.

Warning and Safety instructions

To prevent the risk of fire, the following textiles must not be dried

in this tumble dryer:

–

items which have not been washed.

–

items, such as workwear, which have not been thoroughly

cleaned and which are still soiled with grease, oil or other

deposits (such as cosmetics, lotions etc).

If items have not been thoroughly cleaned there is a danger that

these might self-ignite when heated, even after they have been

removed from the dryer at the end of the programme.

–

items (e.g. mops and floor cloths) which have been treated with

inflammable cleaning agents or which contain residues of

acetone, alcohol, benzine, petrol, kerosene, stain remover,

turpentine, wax, wax remover or other chemicals.

– items which have been splashed with hair lacquer, hair spray, nail

varnish remover or similar substances.

When washing such heavily soiled items ensure that you use

sufficient detergent and select a high temperature. If in doubt,

wash the items several times.

Remove all items such as lighters and matches from pockets.

Warning: Do not switch the tumble dryer off before the drying

programme has finished. If this is done, the laundry must be hung

up or spread out to cool it down.

Warning and Safety instructions

Danger.

This tumble dryer must not be connected to a controllable socket

(e.g. a timer switch or a peak load shut-off device).

If the dryer programme were to be interrupted before the end of the

cooling down phase, the laundry could self-combust.

To prevent the risk of fire, the following must not be tumble dried:

–

items which have been cleaned using chemicals (e.g.

professional dry-cleaning agents).

–

fabrics which contain a large proportion of rubber, foam rubber or

rubber-like materials. For example, products made from latex

foam rubber, shower caps, waterproof textiles, rubberised articles

and items of clothing and pillows with foam rubber filling.

– damaged items which contain padding or fillings (e.g. pillows,

jackets). When damaged, the filling can get out with the risk of

igniting in the dryer.

In many programmes, the heating phase is followed by a cooling

down phase to ensure that the items are not too hot to handle when

you remove them (this also avoids the danger of the laundry

self-igniting). The programme is not finished until the cooling down

phase has been completed.

As soon as the programme has finished, remove all laundry from the

drum.

Fabric conditioner and similar products must be used according

to the instructions on the manufacturer's packaging.

Warning and Safety instructions

Benzine, petrol, paraffin or any easily flammable liquid must not

be stored or used near the tumble dryer. Danger of fire and

explosion.

Do not allow air contaminated with chlorine, fluorine or other

vapours containing solvents to get into the tumble dryer. Fire

hazard.

For tumble dryers with stainless steel surfaces:

The stainless steel surfaces must not come into contact with liquid

cleaning and disinfecting agents which contain chlorine or sodium

hypochlorite. These agents can have a corrosive effect on stainless

steel.

Aggressive vapours containing chlorine can also be corrosive.

Do not, therefore, store containers of these agents near the tumble

dryer.

Warning and Safety instructions

Accessories

Only use genuine Miele original spare parts and accessories with

this tumble dryer.

If non-Miele parts are used, guarantee, performance and product

liability claims may be invalidated.

A Miele tumble dryer can be stacked on top of a Miele washing

machine using the appropriate stacking kit (available as an optional

accessory). Please make sure you order the correct one for the

Miele tumble dryer and Miele washing machine.

If installing the machine on a Miele plinth, (available as an

optional accessory), please make sure you order the correct one for

this tumble dryer.

Miele cannot be held liable for damage caused by

non-compliance with these Warning and Safety instructions.

Warning and Safety instructions

Control panel

a Display

The display lights up when the

machine is switched on.

As soon as the dryer is ready to use,

the Entry menu appears in the

display.

b Start button

The indicator light flashes while a

programme is being selected, and

lights up when the programme starts.

c –, OK, + buttons

See the following pages for more

information.

d + button

For selecting Delay start; Time of day

display

e PC/Optical interface

This is used by Miele service

technicians during servicing work for

testing purposes.

f Low temperature button

For drying delicate fabrics

(Care label symbol r).

g Programme selector

The programme selector can be

turned clockwise or anti-clockwise.

h On/Off button s

For switching the dryer on and off.

To save energy the dryer will switch

off automatically 15 minutes after the

end of the programme/anti-crease

phase or 15 minutes after the dryer is

switched on if it is not operated.

i Door button

Opens the machine door

independently of the electricity

supply.

Before using for the first time

Before using the machine for the first

time, ensure that it is correctly

installed and connected. See

"Installation and connection".

Operating the tumble dryer

Display

The following are shown in the display:

–

Programme selection

–

Programme duration and the

programme start and end time

The following are selected via the

display

–

Special programmes

Denim

Shirts

Outerwear

Proofing

Automatic (if activated)

Smoothing

Pillows

Delicates

Basket - Std. temp.

Basket - Low temp.

Silks handcare

Reactivate

– Delay start

–

The Settings menu

Default settings can be altered to

adapt the dryer to different

requirements. See the end of this

booklet for further information.

–/+ buttons

For altering the values shown in the

display:

– decreases the value or moves the

highlighting upwards.

+ increases the value or moves the

highlighting downwards.

OK button

For confirming the value selected and

choosing the next element.

+ button

For selecting Delay start.

You can also press this button during a

drying programme to check the

estimated programme end time or the

current time of day.

Operating the tumble dryer

Press the On/Off button s briefly to

switch on.

As soon as the dryer is ready to use,

the Entry menu appears.

When the tumble dryer is switched on

for the first time, the Miele Professional

welcome screen will appear.

The Miele Professional welcome

screen will not appear again after you

have entered the language and the

time of day, and run an initial

programme through to the end.

The display for setting the language will

then appear.

Setting the language

C dansk -

deutschB

english H

^ Use the + and – buttons to select the

language you want, and confirm your

choice by pressing the OK button.

A tick

L will appear beside the

language to show that it has been set.

Setting the time (of day) (if necessary)

It is possible to alter the time at any

stage via the Settings menu.

10 :00

Set the time of day

Set the hour with the - and + buttons,

and confirm your setting by pressing

the OK button.

Now set the minutes and confirm

your selection.

Entry menu

The Entry menu will always appear after

the machine has been switched on,

until you select an option.

10:00

Select a programme

Settings F...

See "Settings menu" at the end of this

booklet for more information.

You can now load the laundry into the

dryer and select a programme as

described in "Short instructions".

Before using for the first time

1. Sort the laundry

Garment care label symbols

Drying

q Normal/higher temperature

r Reduced temperature:

Select Low temperature

(for delicate textiles)

s Do not tumble dry

Ironing

I Very hot

H Hot

G Warm

J Do not iron

Before drying

– Wash heavily soiled items very

thoroughly, ensuring that you use

sufficient detergent and select a high

temperature. If in doubt, wash the

items several times.

–

Do not put soaking wet items into the

tumble dryer Make sure that your

laundry is thoroughly spun before

drying.

The higher the spin, the greater the

savings that can be made in energy

and time during drying.

–

New dark-coloured garments should

be washed and dried separately

from light-coloured garments the first

few times they are washed, to avoid

the risk of colours running and

discolouring other garments or even

the plastic components in the tumble

dryer.

Dark-coloured fibres can also settle

on light-coloured garments and vice

versa.

–

Starched laundry can be dried in the

tumble dryer. To achieve the usual

finish, double the amount of starch

should be used.

– Check the seams of padded or

down-filled items to prevent the risk

of fillings coming out. These could

catch fire in the tumble dryer.

– Tie together textile belts and apron

ties to stop them getting tangled.

– Fasten duvet covers etc. to prevent

small items from being trapped

inside them. Fasten hooks and eyes

etc.

–

Stitch in or remove loose underwiring

from bras.

–

Leave jackets open and undo any

long zips so that textiles dry evenly.

–

For an even drying result, it is

important to...

. . . spin,

. . . shake out,

. . . and sort items according to

fabric type, size, care label and the

drying level required.

Notes and tips on laundry care

2. Load the tumble dryer

Using the tumble dryer

incorrectly could cause a fire. Read

the "Warning and Safety instructions"

before using the machine.

Make sure that objects, e.g.

detergent dispensing balls, have

been removed from the laundry.

They could melt and cause damage

to the dryer or the laundry.

–

Do not overload the drum.

Overloading can cause unnecessary

wear and tear to the laundry, give a

disappointing drying result and

cause more creasing.

– To save energy, always observe the

maximum load for each programme

(see "Programme chart").

– Minimum iron fabrics tend to crease

more the greater the load. This is

also the case for garments made

from very fine weave fabrics, such as

shirts or blouses.

If necessary, reduce the size of the

load for these types of fabrics.

3. Select a programme

–

On many programmes, different

drying levels can be selected

depending on individual

requirements

. . . e.g. Normal+ for laundry that you

want to fold and put away immedi

ately after drying.

. . . e.g. Machine iron or Hand iron if

the laundry needs further processing

after drying, e.g. machine ironing.

See "Programme chart".

–

For delicate fabrics with the r care

label, select Low temperature as

well.

– Down-filled garments have linings

which have a tendency to shrink,

depending on the quality of the item.

They can be partially dried using the

Smoothing programme.

– Pure linen should only be machine

dried if specified as suitable by the

manufacturer on the care label, as

the surface of the fabric may

otherwise become rough. They can

be partially dried using the

Smoothing programme.

–

Woollens and wool blends tend to

become matted and shrink if dried in

a tumble dryer. Only dry these

fabrics in a Woollens programme.

–

Loopknit garments (e.g. T-shirts and

underwear) tend to shrink depending

on their quality. Therefore: Do not

over-dry these textiles. When

purchasing these garments it is

advisable to take their shrinkage

properties into account.

Notes and tips on laundry care

A Sort the laundry

It is very important to read the

"Notes and tips on laundry care"

section before proceeding.

B Load the tumble dryer

^ Open the door.

^ Load the drum.

To avoid damaging your laundry,

when shutting the door check that

no items of laundry have become

trapped in the door opening.

^ Shut the door either with a gentle

swing, or lean against it and push it

shut.

Short instructions

C Select a programme

Press the On/Off button s briefly to

switch on.

Please note:

–

If no further selection is made within

15 minutes, the dryer will switch off

automatically.

–

This does not apply to machines with

a payment system.

Turn the selector to the programme

you require.

The display will vary according to which

programme has been selected.

With the Cottons and Minimum iron

programmes, the drying level is

selected with the programme selector.

To select a Special programme

A selection of programmes will appear

in the display when you select Special

programmes.

Denim

Shirts

Outerwear

Use the + or - button to highlight the

programme you want. The arrow H

in the display indicates that there are

further options.

^ Confirm your selection by pressing

the OK button.

On some Special programmes, the

drying level can be altered as follows:

Shirts

Normal

Duration: 0:36h

^ Use the + or - button to change the

drying level.

For the drying level options, see

"Programme chart".

Warm air, Cool air and Basket

programmes

1:00 h Warm air

Duration: 1:00h

The programme duration can be

increased or reduced using the + or

– buttons.

Short instructions

Low temperature button

For drying particularly sensitive

fabrics (care symbol r), e.g.

acrylics, press the Low temperature

button.

Because the heater rating is reduced

for the Low temperature setting, clothes

dry more slowly thus lengthening drying

times.

+ button

See "Delay start".

Coin operation

If your machine has a payment system,

the amount of credit required will

appear in the display.

Opening the door or cancelling the

programme after it has started may

cause loss of credit (depending on

how the machine was set up).

D Start the programme

The indicator for the Start button will

flash as soon as a programme can be

started.

Press the Start button.

–

Prog. running will appear in the

display, followed by Drying and the

programme duration.

–

With programmes with drying levels,

e.g. Machine iron, Hand iron etc.,

the drying level reached will be

shown in the display later on.

Changing the programme sequence

Further information about the following

can be found under "Changing the

programme sequence":

–

Coin box

–

Changing a programme once it has

started

–

Cancelling the current programme

–

Adding or removing laundry after a

programme has started

–

Power cuts

– Time left

Programme duration/Estimated time

left

When a programme is selected, the

estimated duration will appear in the

display. Please be aware that it is only

an estimate!

The following factors all affect the

estimated time remaining: residual

moisture content after spinning; type of

fabric; size of load; room temperature;

fluctuations in power supply.

The electronics assess conditions in the

dryer and adjust the estimated time

remaining for a more accurate reading.

Because of this, the time displayed can

alter during the course of a programme.

Short instructions

Before the end of a programme

There is a cooling down phase at the

end of the drying sequence: Cooling

down will appear in the display. The

programme will not finish until the

cooling down phase has been

completed.

There is no cooling down phase at the

end of the following programmes:

Woollens handcare, Smoothing.

Do not switch the tumble dryer off

before the end of the drying

programme.

E Remove the laundry when the

programme has finished

Anti-crease (if activated) and Finish will

appear in the display to indicate that

the programme has finished.

Please note:

– To avoid creasing, during the

anti-crease phase the drum will

continue to turn at intervals until the

laundry is removed.

The anti-crease phase is not

activated in the following

programmes; Woollens handcare,

Basket programmes.

–

The dryer will switch off automatically

15 minutes after the end of a

programme/the end of the

anti-crease phase.

It is advisable to remove laundry as

soon as the programme has

finished.

Open the door.

^ Remove everything from the drum.

Check that all items have been

removed from the drum. Anything

left in the dryer could be damaged

by overdrying when it is next used.

The drum lighting will come on when

the door is opened. It will go out a few

minutes later to save energy.

Press the On/Off button s briefly to

switch off the machine.

The display will go out.

Close the door.

Maintenance after each drying

programme

Please see "Cleaning and care" for

details.

Short instructions

Depending on the Delay start setting,

you can set the time you wish a

programme to finish or start at, or you

can delay the start of the programme.

Factory default: Delay start not

activated.

To select Delay start

Select the programme you want and

then press the + button.

10:00

Start:

10:00

Finish:

11:16

Example: The display will show the

current time of day at the top, the time

the programme will start in the middle

and the time the programme will finish

at the bottom.

10:00

Start:

11:14

Finish:

12:30

Use the + controls to select the

desired time.

The Start and Finish times will now be

postponed by 30 minutes. The

maximum time that an automatic

programme start can be delayed by is

24 hours.

Use the – button to reduce the time.

Confirm your selection by pressing

the OK button.

To begin delay start

Press the Start button.

Normal

Start in: 1:14h

The delay start time will now count

down in minutes until the start of the

programme.

The drum will turn briefly every hour to

help prevent creasing.

Changing the programme sequence

While the Delay start time is counting

down, you can still...

. . . select the Low temperature option

or another drying level.

. . . press the Door button and add or

remove laundry. After closing the door,

press the Start button.

To alter delay start

^ Press the + button.

Use the - or + button to alter the time.

Confirm your selection by pressing

the OK button.

To delete Delay start

Press the + button.

Press and hold the – button until the

time stops reducing.

Confirm your selection by pressing

the OK button.

The programme will now start immedi

ately.

To cancel Delay start

Turn the programme selector to

Finish.

Delay start

Basic programmes

Cottons t ** Max. load 6.5 kg*

Use for Normal wet cotton laundry, as described in Cottons Normal .

Notes

–

Items are dried to a "Normal" level only.

–

Cottons t is the most energy-efficient programme for

drying normal wet cotton laundry.

Cottons max. 6.5 kg

Normal+, Normal

Use for

–

Single and multi-layered cotton fabrics such as:

–

Towelling, T-shirts, underwear, flannelette bed linen and

baby clothes.

–

Workwear, jackets, cotton blankets, aprons, face flannels,

tea towels, bed linen, towels, table linen that can be

washed hot, overalls.

Note – Do not overdry loopknit fabrics (e.g. T-shirts, underwear,

baby clothes), as they have a tendency to shrink.

Low temperature Select for fabrics with the r symbol.

Hand iron, Machine iron

Use for – Cotton or linen fabrics

– Table linen, bed linen, starched laundry.

Note – To prevent laundry from drying out, it should be rolled up

until you are ready for ironing.

Low temperature Select for fabrics with the r symbol.

Minimum iron max. 3.5 kg

Normal+, Normal, Hand iron

Use for

–

Minimum iron cotton, synthetic and mixed fibre fabric

–

Workwear, overalls, pullovers, dresses, trousers, table linen

Low temperature Select for fabrics with the r symbol.

Weight of dry items

** Note for test institutes:

Test programme in accordance with regulation 392/2012/EU measured according to EN 61121

Programme chart

Towelling max. 6.5 kg

Normal+

Use for

–

Large quantities of single-layer and multi-layer towelling items.

–

Towels, dressing gowns, face flannels, towelling bedding.

Woollens handcare max. 2.5 kg

Use for Woollen garments.

Note

–

Items are dried and aired briefly.

–

Remove garments as soon as the programme has finished

and leave to finish drying at room temperature.

Timed drying, warm air (15-60 minutes**) max. 6.5 kg

Use for

–

Multi-layered fabrics whose layers have different drying

characteristics,

– Voluminous items, e.g. jackets, pillows.

– For drying individual items.

– Bath towels, swimwear, tea-towels.

Note – Do not select the longest drying time to start with. Check the

items as you are drying them to find the optimum time.

Low

temperature

Select for fabrics with the r symbol.

Timed drying, cool air (10-120 minutes**) max. 6.5 kg

Use for – Any item which only needs airing.

Weight of dry items

** The upper and lower limits of the programme duration can be changed by a Service technician.

Programme chart

Special programmes

Denim max. 3.5 kg

Normal, Hand iron r

Use for

–

Denim garments, e.g. jeans, jackets, skirts, shirts.

Shirts max. 2.5 kg

Normal, Hand iron r

Use for

–

Shirts and blouses.

Outerwear max. 3.5 kg

Normal, Hand iron r

Use for

–

Outerwear which is suitable for drying in a tumble dryer.

Proofing max. 2.5 kg

Normal

Use for – Microfibre fabrics, skiwear, fine, closeweave cotton garments

(poplin) or tablecloths which are suitable for drying in a tumble

dryer and have been treated to provide a water and dirt resistant

finish.

Note – This programme includes a proofing fixing phase.

– Only use proofing agents containing fluorochemical compounds

which which are stated by the manufacturer as being "suitable

for use on membrane textiles". Do not dry items which have

been treated with proofing agents containing paraffin. Fire

hazard!

* Weight of dry laundry

Programme chart

The following programme must be activated by a Service technician:

Automatic Max. load 3.5 kg*

Normal+, Normal, Hand iron r

Use for

–

Mixed loads of garments suitable for the Cottons and Minimum

iron programmes. Sort according to colour.

Smoothing max. 3 kg

Use for

–

Cotton and linen fabrics.

–

Minimum iron mixed fibre, cotton or synthetic fabrics, e.g.:

trousers, anoraks, shirts.

Note

–

Smooths out creasing caused during the spin cycle in the

washing machine.

–

Remove garments as soon as the programme has finished and

leave to finish drying at room temperature.

Weight of dry items

Programme chart

Standard pillows max. 2.5 kg

Normal

Use for

–

Feather or down pillows.

–

Quantity: 2 pillows 80x80 cm

Delicates max. 4 kg

Normal+, Normal, Hand iron r

Use for

–

Delicate cotton, synthetic and mixed fibre fabrics

–

Thin pullovers, dresses, trousers, overalls, table cloths, shirts,

blouses.

–

Lingerie and appliquéd fabrics.

Important

–

Low creasing.

Weight of dry items

Programme chart

Basket programmes (20-90 min)

Note

–

The drying basket (optional

accessory) must be in place when

items are dried or aired using this

programme.

–

To prevent the risk of damage when

the drum rotates, do not place large

items which could come into contact

with the drum or drum ribs in the

drying basket (e.g. knee length boots, large bags or

rucksacks).

–

Sleeves, belts and ties should be folded in or secured so that

they are fully contained within the drying basket.

–

Use this programme to dry items which are suitable for drying

in a tumble dryer but which are not suitable for drying using

mechanical action.

– It is essential to observe the operating instructions for the

drying basket.

Use for – See the operating instructions supplied with the drying basket.

Basket Std. temp. (20-90 min) max. load in the basket 3 kg

– For thermally stable textiles / items

Basket - Low temp. (20-90 min) max. load in the basket 3 kg

– For thermally sensitive textiles / items

Silks handcare max. 1.5 kg

Use for

–

Silks, e.g. blouses and shirts.

Important

–

Smooths out creasing.

–

Remove garments as soon as the programme has finished and

leave to finish drying at room temperature.

Reactivate max. 2.5 kg

Normal

Use for

–

Outerwear which is suitable for drying in a tumble dryer.

Note

–

Makes the fibres more water-repellant.

Weight of dry items

Programme chart

Payment system

Opening the door or cancelling the

programme after it has started may

cause loss of credit (depending on

how the machine was set up*).

* A Miele service technician can re-set

the payment system so that

programming changes can be made

within a specified time period.

Changing a programme once it

has started

You cannot change to another

programme once a programme has

started (this prevents unintentional

alterations). If the programme selector

is altered, the words Programme

cannot be changed appear if the

selector is not turned back to the

original programme.

You will need to cancel the current

programme before you can select a

new one.

Cancelling the current

programme

Turn the programme selector to

Finish.

When Finish appears in the display,

this shows that the programme has

been cancelled.

Open the door.

Close the door.

Select a new programme.

Press the Start button.

Adding or removing laundry

after a programme has started

The laundry, the drum and the

back of the machine all become

very hot during operation. Take care

when in the vicinity of the machine,

when opening the door and

handling freshly dried laundry.

Danger of burning.

Press the Door button.

Open the door.

^ Add or remove items as required.

^ Close the door.

^ Press the Start button.

Power cuts

– If the dryer is switched off during a

drying programme or there has been

a power cut:

^ When the power is restored and/or

the machine is switched on again,

confirm with OK and start the

programme again.

Time remaining

The time left shown in the display may

now vary from the actual drying time.

Changing the programme sequence

Cleaning the fluff filters

Fluff from items being dried is collected

by the fluff filters in the door and the

door opening. Clean the filters after

each drying programme*.

Cleaning them whilst dry

^ Open the door and pull the fluff filter

(1) out as illustrated.

Use your fingers or a vacuum cleaner

to remove the fluff from the surface of

the filter.

Remove any fluff from the hollow part

of the door opening. You could also

use a cleaning brush which is

available as an optional extra from

your Miele dealer or the Miele Spare

Parts Department or use a vacuum

cleaner.

Once clean, push the filter back into

the door holder until it clicks into

position. Ensure it is facing the

correct way.

Also clean the door seal (2) with a

damp cloth.

Use your fingers or a vacuum cleaner

to remove the fluff from the two fluff

filters in the door opening.

Close the door.

* The fluff filters should be

checked and cleaned regularly but

always clean immediately the Clean

out airways message appears.

Cleaning and care

Cleaning them with water

If there is a great deal of compacted

fluff on any of the filters, they can be

removed and cleaned under hot

running water.

Open the door and pull the fluff filter

out of the door as described

previously.

The two filters in the door opening can

also be removed if you need to clean

them with water.

Turn catch a until you hear it click.

Pull the filter by the dial out of the

door opening as shown b.Dothe

same on the other side.

Rinse all the filters under hot, running

water.

Also clean the airways underneath

each one with a vacuum cleaner, for

example.

Dry the filters thoroughly with care.

Replacing the filters

Do not replace the filters if they

are damp or wet. Damp or wet filters

could cause operational faults.

Push the large filter back into the

door holder until it clicks into position.

Ensure it is facing the correct way.

Replace the filters in the door

opening by first inserting them at the

bottom and then pressing them into

place at the top.

Lock both catches (you will hear

them click).

Cleaning and care

Cleaning the tumble dryer

Disconnect the tumble dryer

from the mains electricity supply.

Do not use solvents, abrasive

cleaners, glass cleaners or

all-purpose cleaners. These could

damage plastic surfaces and other

parts.

The tumble dryer must never be

hosed down.

^ Clean the housing and the control

panel with a slightly damp cloth and

a mild detergent or soapy water.

^ The drum and other stainless steel

parts can be cleaned with a suitable

proprietary stainless steel cleaner

following the manufacturer's

instructions.

Dry all parts with a soft cloth.

Cleaning and care

Cleaning the heat exchanger

Check the heat exchanger unit

regularly. It should always be

cleaned immediately the Clean

condenser unit or Clean out airways

message appears.

Removing the heat exchanger

^ Open the access panel.

The hooks at the side will prevent the

panel from falling off.

Now remove the panel by pulling it

diagonally upwards.

Then place it to one side.

Turn the lever on the inner cover

downwards to the vertical position.

^ Pull the cover forwards.

^ Remove it by pulling it diagonally

upwards.

Turn the lever on the heat exchanger

to the vertical position.

Cleaning and care

Pull the condenser (heat exchanger)

unit out of its housing by the handle

Checking the condenser unit (heat

exchanger unit)

Hold the condenser unit up to the

light as shown.

Check to see if there is any fluff

inside it. The arrows in the illustration

above indicate where to look.

If you cannot see any fluff:

Replace the condenser unit (see

following page).

If you can see some fluff:

Clean the condenser unit as

described below.

To clean the condenser unit

Use a shower head or similar to rinse

the unit out as shown.

– From the sides.

–

From the front.

Fluff is washed out by the water.

Cleaning and care

Check the condenser unit again for

any visible fluff, and if necessary

flush it through again until it has all

gone.

Also make sure the rubber seals are

clean.

The rubber seals must not be

removed and must be free of kinks.

To check and clean the condenser unit

housing

Remove any soiling still visible inside

the housing by hand using a damp

cloth. Do not try and access areas

you cannot reach by hand.

Replacing the condenser unit

Push the condenser unit all the way

back into the housing, until it clicks

into place.

The handle

for the condenser unit

must be at the top, and the lever at

the bottom.

Turn the lever down to the horizontal

position, making sure that the hook

on the lever clicks into the groove at

the bottom.

When replacing the inner cover,

ensure that the rubber seal fits

correctly into the groove.

^ Replace the cover making sure the

hooks locate correctly. To do this,

hold it at an angle and push it gently

downwards.

^ Then turn the lever upwards into the

horizontal position to lock the cover.

^ Replace the service panel and press

the upper edge until it clicks into

position.

It is important to ensure that both the

condenser unit and the cover are

correctly positioned and locked

otherwise water may leak from the

machine.

Cleaning and care

Problem solving guide

With the help of the following notes minor faults in the performance of this dryer,

some of which may result from incorrect operation, can be put right without

contacting the Service Department.

Repair work to electrical appliances should only be carried out by a suitably

qualified person in accordance with current local and national safety

regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

Fault messages in the display

Problem Possible cause Remedy

Adjust

the load

This is not a fault.

The electronic unit has

recognised that there is no

laundry in the drum and

cancelled the programme.

Drying individual garments or

items which are already dry

can also cause the programme

to be cancelled.

Use the Warm air

programme (timed

drying) to dry individual

items.

To delete the fault

message:

– Open the door.

Technical

Fault

A fault code eg F47

may also appear in

the display

No obvious cause.

In some circumstances, Clean

out airways will have appeared

in the display already.

– See next page: Clean

out airways.

You cannot start another

programme whilst this

message shows in the display.

–

Follow the instructions

in the display.

–

Try to start the

programme again.

Problem solving guide

Problem Possible cause Remedy

Power failure

Programme

stopped

If the dryer is switched off

during a drying programme

or there has been a power

cut:

–

After switching the dryer on /

power has been restored,

confirm with OK and start the

programme again.

The following

appears at the

end of the

programme:

Service info

Clean the

condenser

unit

The dryer is reminding you

that the condenser unit

(heat exchanger unit)

needs to be cleaned.

–

Clean the condenser unit.

To delete the fault message:

–

Confirm with OK.

You can adjust the setting

which controls when or if

the message Clean the

condenser unit appears.

See "Settings menu J, Cleaning

the condenser unit".

Clean out

airways

Clean the filters

appears at the

end of the

programme or

after a

programme

has been

cancelled.

The dryer is not working

efficiently or economically.

Possible cause: A build-up

of fluff or detergent

residues.

– Cleaning the filters is usually all

that is required.

However, if the message does

not go out after you have

cleaned the filters, then also

check all the possible causes

described under "The drying

process goes on too long or

even switches off".

To delete the fault message:

–

Open and close the door, or

confirm with OK.

You can adjust the setting which

controls when or if the message to

clean out the airways appears.

–

See "Settings menu J, Clean

the airways".

Drain fault

Check drainage

The drain hose is kinked.

–

Remove the kink.

To delete the fault message:

–

Confirm with OK.

Programme

cannot

be changed

An attempt has been made

to alter a programme while

it is in progress.

–

You will need to cancel the

current programme before you

can select a new one.

Problem solving guide

An unsatisfactory drying result

Problem Possible cause Remedy

The laundry is not

sufficiently dry.

The load consisted of

different fabrics.

–

Finish drying using the

Warm air programme.

–

Select a different

programme next time

(see "Programme

chart").

Feather filled pillows

smell after drying.

Feathers are a natural

product and this is quite

normal.

The smell will dissipate

after sufficient airing.

Items made of synthetic

fibres are charged with

static electricity after

drying.

Synthetic fibres tend to

attract static charge.

Static charge can be

reduced by adding a

fabric conditioner to the

final rinse in the washing

programme or a fabric

conditioner sheet to the

load when drying.

There is a build-up of

fluff.

Fluff is principally the

result of friction when

garments are being worn

and to some extent when

they are being washed.

Machine drying causes

hardly any fluff to form

and has no appreciable

effect on the lifetime of

the fabric.

Fluff is collected by the

fluff filter and can be

easily removed (see

"Cleaning and care").

Problem solving guide

Other problems

Problem Possible cause Remedy

The drying

process goes on

too long or even

switches off.

You might be asked to

clean the ducting

system/filters again.

Please check all possible

causes, described below.

Ventilation to and from the

dryer may be insufficient,

e.g. because it is installed

in a room which is too

small. This can cause the

temperature in the room to

rise sharply.

Open a door or window while

the dryer is in operation for

increased air flow.

The vents below the door

are blocked.

– Remove any objects that are

blocking the vents.

The fluff filters are

clogged up with fluff or

were still wet when they

were replaced.

– Remove any fluff.

– The fluff filters must be

completely dry.

Detergent residues, hair

and fine fibres can block

the condenser unit.

Check the condenser unit from

time to time and clean it if

necessary.

The laundry has not been

spun sufficiently.

Make sure that your laundry is

thoroughly spun at the

appropriate spin speed in the

washing machine.

The tumble dryer has

been overloaded.

Do not exceed the maximum

load for the programme

selected.

Metallic components, e.g.

zips have prevented the

dryer from registering the

correct moisture level in

the laundry.

–

Open zips next time.

If the problem occurs again,

dry garments with long zips

using the Warm air programme

(timed drying).

Problem solving guide

Problem Possible cause Remedy

Water leaks from

the dryer after the

condenser unit has

been cleaned.

–

The inner cover of the

condenser unit has not

been locked properly

and/or the condenser unit

has not been positioned

correctly.

–

Fluff has collected in the

condenser unit housing.

–

Ensure that the

condenser unit is

positioned correctly and

lock the inner cover.

–

Check the rubber seals.

–

Use a cloth to remove

any visible fluff from the

inside of the condenser

unit housing.

The interior drum

lighting does not

come on.

The lighting switches off

automatically (to save

energy).

–

It will switch on again

after the door has been

closed and then opened.

–

If the lamp needs to be

replaced, follow the

instructions in "Changing

the lamp" at the end of

this section.

Power cuts. – After the power supply has been restored, switch the

dryer on using the s button.

– Confirm with OK.

Problem solving guide

Problem Possible cause Remedy

The programme does

not start and the display

is dark.

No obvious cause.

–

Is the dryer switched

on?

–

Is the door closed

properly?

–

Has the fuse or circuit

breaker tripped?

When the power comes

back on after a power

cut, confirm with OK and

start the programme

again.

The dryer switches off

automatically after 15

minutes if no further

selection is made.

Switch the dryer on.

The display is in a

different language.

A different language has

been selected in "Settings

J" "Language J".

Set the language you

want. The flag symbol

will guide you.

The indicator lamp for

the Start button flashes

when a programme is

being selected.

This is not a fault.

The flashing indicates

that a programme can be

started.

Once the programme has

been started, the Start

button stops flashing and

lights up constantly.

The display is dark and

the light ring around the

multi-function selector

is not lit up.

The Start button light

flashes slowly.

The display has switched

off automatically to save

energy (Standby mode).

The same applies to the

programme selector.

The display and

programme selector are

lit up after pressing a

button or turning the

programme selector.

The programme selector

light goes out when the

Settings menu has been

selected.

The programme selector

light comes on when a

programme is selected.

If the problem persists,

there is a fault.

Contact the Miele Service

Department.

Problem solving guide

Changing the lamp

Disconnect the tumble dryer from

the mains electricity supply.

Open the door.

You will find the interior lamp cover at

the top of the drum aperture.

^ Insert a suitable tool, such as a wide

bladed screwdriver, under the side

edge of the lamp cover as illustrated.

Apply a little pressure and whilst

doing so turn your wrist in the

direction of the arrow to open the

cover.

The cover will open downwards.

The temperature resistant lamp should

only be ordered from your Miele dealer

or the Miele Spare Parts Department.

The lamp specification and

maximum wattage is stated on the

data plate and on the lamp cover.

Replace the lamp.

To close the cover push it upwards

and press it on the left and right until

you hear it click into position.

Ensure that it is fitted into

position securely, as any moisture

could cause a short circuit.

Problem solving guide

Repairs

In the event of any faults which you

cannot remedy yourself, or if the tumble

dryer is under guarantee, please

contact

–

your Miele Dealer

–

the Miele Service Department (see

back cover for contact details).

When contacting the your Dealer or the

Service Department, please quote the

model and serial number of your dryer

both of which are shown on the data

plate.

PC / Optical interface

The indicator or check light marked PC

on the fascia panel is the interface used

by Miele service technicians during

servicing work for testing purposes and

for updating the machine´s programme

data.

Optional accessories

Optional accessories for this dryer are

available from your Miele Dealer or from

the Miele Spare Parts Department.

After sales service

Front view

a Mains connection cable

b Control panel

c Door

d Service panel for condenser unit

e Four height adjustable screw feet

f External drainage options (e.g. via

wash basin, wash basin drain outlet

or gully)

Optional accessory: Extension hose

g Intake and exhaust vents for cooling

the condenser unit

Installation and connection

Side view

Rear view

a Protruding lid edge (see arrows) for

holding when moving the tumble

dryer.

b Air exhaust vent for cooling the

condenser unit

c Stainless steel plith (open or closed,

optional Miele accessory)

View from above

Washer-dryer stack

The tumble dryer can be combined with

a Miele washing machine in a

washer-dryer stack. A stacking kit is

required which can be purchased from

Miele. The stacking kit must be fitted by

a Miele authorised service technician.

Installation and connection

Installing the tumble dryer

Make sure the dryer door can be

opened without hindrance after

installation.

Transporting the dryer to its

installation site

When moving the dryer, hold it by the

lid where it protrudes to the rear. To

manoeuvre the dryer out of its packing

case to its installation site you will also

need to hold it by the front feet.

Ensure the tumble dryer is stable

during transportion.

Levelling the machine

The machine must be perfectly level to

ensure safe and proper operation.

The screw feet can be adjusted to

compensate for any unevenness in

the floor.

Installation and connection

Never block the vents on the

dryer.

In order to ensure sufficient

ventilation to the dryer, do not

reduce the vent gap between the

underside of the dryer and the floor

with a plinth, deep-pile carpet, etc.

This tumble dryer is not suitable for

building under.

Room in which the dryer is located

Air taken in for use in the drying

process will be warm when it is

expelled from the underside and back

of the dryer. This expelled air heats up

the air in the room. It is therefore very

important to ensure that the room is

adequately ventilated, particularly if the

dryer is located in a small room.

Otherwise running times and energy

consumption could be increased.

Securing the tumble dryer against

slippage

Secure both front feet on the

dryer using the fixing brackets

supplied.

Payment system

The dryer can be fitted with a payment

system (optional accessory).

This must be connected and

programmed by a Miele Service

technician.

Coins/tokens must be removed from

the payment system regularly,

otherwise it will become blocked.

–

Note for service technician:

When connecting to a payment

system, the plug connector on the

push button switch (see wiring

diagram) must be disconnected

from its position ex-works and

reconnected to the position for

payment system operation.

Failure to do this can cause the

payment system to malfunction.

Installation and connection

External drainage of the

condensed water

The condensed water is pumped

away through the drain hose which is

located at the back of the dryer at the

bottom.

Drain hose length: ..............2m

Delivery head: .................1m

Do not pull on the drain hose

and do not allow it to become

kinked as this could damage it.

Drain hose connection:

1. Direct into a sink or basin.

– Hook the hose over the edge and

secure.

– Use the bow-shaped guide (see

illustration on the right).

2. Connected securely to a floor gully.

3. Connected directly to a sink drain

outlet.

Connection to a sink drain outlet

To connect the drain hose to a sink

drain outlet you will need to use the

adapter and hose clip located at the

back of the dryer at the bottom.

Remove adapter 1 and hose clip 3

behind it.

^ Fit adapter 1 to the sink drain outlet

using nut 2.

Secure the drain hose with hose clip

3 to the nut.

Installation and connection

Electrical connection

All electrical work must be

carried out by a suitably qualified

and competent person in

accordance with current local and

national safety regulations (BS 7671

in the UK).

This machine is supplied with a

connection cable and moulded plug

(BS 1363) for connection to a 230 V

mains supply.

The machine must only be operated

with the voltage, frequency and fuse

rating shown on the data plate supplied

with the machine. Please ensure these

match the site mains supply.

We recommend connecting the

machine to the power supply via an

IP44 plug and socket which must be

easily accessible for servicing and

maintenance work after the machine

has been installed.

Do not connect the machine via an

extension lead. Extension leads do not

guarantee the required safety of the

machine (e.g. danger of overheating).

For extra safety and protection we

recommend connecting the machine by

a 30 mA residual current device (RCD).

An electrical safety test must be carried

out after installation and after any ser

vice work.

The mains connection cable may only

be replaced by an original Miele spare

part.

If the machine is disconnected

from the electricity supply adequate

measures must be taken to ensure

that the machine cannot be

reconnected to the electricity supply

until all work has been carried out.

The machine must be

permanently connected to the

electricity supply to enable the

programme to complete and to

enable the load to cool down after

drying. For this reason it must not be

connected to devices such as timers

which would switch it off

automatically.

WARNING

THIS MACHINE

MUST BE EARTHED

Installation and connection

Height 850 mm

Width 595 mm

Depth 710 mm

Depth with door open 1188 mm

Weight 58 kg

Drum volume 130 litres

Maximum capacity 6.5 kg dry weight

Length of connection cable 1600 mm

Voltage

Connected load

Fuse rating See data plate

Lamp wattage

Test certificates awarded

Max. load bearing

in operation

approx. 710 Newton

Product safety standard According to EN 10472, EN 60335

Sound emission level

in accordance with

EN ISO 11204/11203

<70dBre20µPa

Technical data

Changing default settings

Default settings can be altered to

adapt the tumble dryer to different

requirements.

Depending on the programmable

status, the Settings/Supervisor level

menu can be locked with a code to

prevent it being accessed by

unauthorised personnel (the Language

J setting can still be altered).

– Code not required

Some of the settings may be

changed.

–

Code required

All of the settings may be changed.

Please contact Miele for details.

Note:

The tumble dryer must be

commissioned as described at the

beginning of this booklet.

Opening the Settings menu

If the Settings menu is not locked,

some of the settings may be

changed.

A The entry menu showing the current

time of day will appear after the dryer

has been switched on, until you

select a programme.

10:00

Select a programme

Settings F...

B Press the OK button.

C This will take you into the Settings

menu.

Selecting a setting

C Back A

Language F

Supervisor level H

D Use the + and – buttons to select the

setting you want, and confirm your

selection by pressing the OK button.

–

The arrow H in the display indicates

that there are further options.

–

If you do not make a selection in the

Settings menu and in its sub-menus

within approx. 15 seconds, the

display will revert to the previous

menu.

Closing the Settings menu

Back A

Language F

Supervisor level

Select Back and confirm your

selection with the OK button.

Opening the Settings menu via

the Supervisor level

The Settings menu can be locked

against unauthorised use (except for

the Language option J). It will then

only be able to be accessed at

Supervisor level by entering a code.

C Back A

Language F

Supervisor level

^ Open the Supervisor level sub-menu

To enter the code

C Back A

Access via code

Change code

Confirm Access via code.

Enter the code 000(factory default

setting). If you enter the code wrongly

three times, you will be locked out of

the Supervisor level for an hour.

Settings menu

000

Enter code

Use the + button to enter the first

number.

Confirm your selection of this number

by pressing the OK button.

Now enter the second number.

Repeat the process until all three

numbers have been entered.

To confirm the code

Yes 000 No

Confirm code

^ Confirm the code with OK (Yes is

highlighted).

To correct the code

Press the + button so that No is

highlighted.

Confirm by pressing the OK button.

Enter the correct code.

To change the code

See the "Supervisor level" setting.

Language J

You can select the language

displayed via the Languages J

sub-menu.

The flag after the word Language acts

as a guide to prevent a language which

will not be understood from being set.

Supervisor level

You can alter the access code to the

supervisor level.

^ Enter the old code.

^ Enter a new code.

After you have confirmed the new code,

the display will change to the beginning

of the Settings menu.

Settings menu

Anti-crease

At the end of the programme the

drum can be set to rotate at intervals

for one or two hours to prevent

laundry creasing, if you do not wish

to remove it immediately.

–

Factory default: Off.

–

Buzzer

When the buzzer function has been

activated, an audible tone sounds at

the end of a programme.

– Off

(factory default)

The buzzer will still sound if there is a

fault even if it has been deactivated.

– Normal

The buzzer sounds at the end of a

programme.

–

Loud

The buzzer sounds at maximum

volume at the end of a programme.

Time of day

First select whether you want the

clock displayed as a 24 hour or 12

hour clock, or to not display it at all.

Then set the current time of day.

–

24 h clock or 12 h clock

Once the clock display has been

selected, the time of day can be set.

To set the time of day:

Set the hour with the – and + buttons,

and confirm your selection by

pressing the OK button.

^ Now set the minutes and confirm

your selection.

– Time not displayed

If Delay start is activated (see

Settings Delay start), then the timer

will only show the option Start in or

Finish in in hours/minutes.

Display contrast

Display brightness

There are ten different display

contrast and display brightness

settings.

The bars show you the setting.

–

Factory default: level 5

Settings menu

Standby

To save energy, the display goes out

after 10 minutes and the indicator

light for the Start button flashes

slowly.

The display is switched on again by

moving the programme selector or

touching one of the buttons, without any

effect on any programme that is

running.

–

Standby comes on:

...ifaprogramme is not selected.

. . . after the Start button has been

pressed in a programme that is

running.

. . . after the end of a programme.

– Not in current prog.

(default setting)

Standby is activated if no

programme selection is made after

the end of a programme - but not

during a programme that is running.

Extended cool down

The cooling down phase which takes

place before the end of a programme

can be lengthened if required. This

makes the garments easier to handle.

The bars show you the setting.

–

from 0-18 mins.

–

Factory default: 0 mins (normal

cooling down period)

The programme duration will increase

accordingly.

You cannot extend the cooling down

time for the Warm air, Cool air,

Woollens handcare or Smoothing

programmes.

Drying levels

Cottons

Please note: Changing the settings for

drying levels in the Settings menu will

also affect the Cottons t

programme.

Minimum iron

You can alter the drying levels for the

Cottons and Minimum iron

programmes.

The bars show you the setting.

– from drier to

– damper

– Factory default: level 4

Machine iron

The drying level Machine iron can be

altered separately in the Cottons

programme.

The bars show you the setting.

–

from drier to

–

damper

–

Factory default: medium.

Settings menu

Clean out airways

The electronic unit in the dryer

detects the degree of a blockage

caused by fluff or detergent residues

in the fluff filter or ducting, and the

following prompt comes up in the

display: Clean out airways. You can

decide at what level of fluff this

message should appear.

You will have an idea of how often this

should be done after a few drying

programmes.

–

Off

Clean out airways does not appear.

In cases of a very severe blockage in

the ducting, the programme is

cancelled and the message Clean

out airways comes up regardless of

this option.

– Heavy

Clean out airways only appears

when there is a heavy build-up of

fluff

–

Normal

(Factory default setting)

–

Light

Clean out airways appears when

there is only a small build-up of fluff.

Clean condenser unit

Check the condenser unit from time

to time, and clean it if necessary.

The Clean the condenser unit

maintenance message will remind

you to do this. You can decide after

how many hours you want the

message to appear.

The number of hours will depend on

how much fluff collects in the

condenser unit.

If the condenser unit gets choked with

fluff, or conversely there is hardly any

build-up of fluff in it, the number of

hours can be adjusted accordingly.

– Factory default: after 400 h.

– Off

– Time interval of 100 to 1600 hours

Settings menu

Delay start

You can set a later start time using

Delay start (see "Delay start").

You can decide how this time is

displayed.

–

Programme end

The finish time for the programme is

selected.

–

Programme start

The start time for the programme is

selected.

– Time until start

The time to the start of the

programme is selected in

minutes/hours.

– Off

(factory default)

By pressing the + button, the time

remaining and the finish time for the

programme is displayed.

Settings menu

Alteration rights reserved/3715

M.-Nr. 09 869 880 / 04

www.miele.com/marine-service

merica: +1 609 419 4376

ustralia, Asia, Oceania: +61 3 9764 7880

Europe, Africa, Middle East: +49 5241 89 66 877

International Service Contacts

E-mail: service@miele-marine.com

Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Miele PT 5135C in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Miele PT 5135C

Miele PT 5135C User Manual - German - 60 pages

Miele PT 5135C User Manual - Dutch - 56 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Miele PT 5135C Manual

Product: