44335
64
Zoom out
Zoom in
Previous page
1/72
Next page
Operating instructions
for dishwashers
It is essential to read these
operating instructions before
Q
installing or using the machine,
to avoid risk of accident
or damage to the machine. M.-Nr. 04 873 380
Contents
Guide to the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Water softener/reactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the water hardness level/Filling the salt reservoir . . . . . . . . . . . . . . . . 12/13
Add salt indicator light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Adding rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rinse aid dosage setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Loading the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Loading examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Flap up racks, positioning rail, adjusting the upper basket. . . . . . . . . . . . . . . 22/23
Not suitable for dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Programme selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30/31
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32/33
Programme change; interrupting a programme; programme sequence display. 32/33
Removing load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Checking the water level/Increasing the water intake time . . . . . . . . . . . . . . . . . 41
Dealing with minor faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Special accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Comparison tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Contents
2
Guide to the appliance
Miele dishwashers are available in
three versions:
1. “Freestanding“ dishwashers
“Freestanding“ dishwashers do not re-
quire any special installation fixings in
the kitchen.
A decor frame can be added to take a
panel for matching the dishwasher to
the kitchen fronts.
2. Integrated (“i“) dishwashers
“i“ dishwashers are specially designed
for building under a continuous work-
top.
The control panel with its accessories
is included with the “i“ dishwasher in a
separate package for on-site fixing.
The front is designed to be fitted with a
base unit front to match the kitchen fur-
niture.
The dishwasher does not have a plinth
facia. The plinth area can be covered
either with facia to match your kitchen
furniture if available, or another facia.
The separate plinth facia can be fitted
to match the height of adjacent plinths.
The plinth return is freely adjustable.
All notes on installation are described
in the chapter on “Installation instruc-
tions“.
3. “U“ dishwashers
The built-under(“U“) dishwashers use
the integrated (“i“)-dishwashers as the
basic machine.
By using a decor set (GDU) the “i“ dish-
washer can be converted into a “U“
model dishwasher.
GDU installation instructions are in-
cluded in a separate installation leaflet
supplied with the decor set.
Guide to the appliance
3
View of the machine
Control panel (facia)
Guide to the appliance
4
1 Upper spray arm (not visible)
2 Cutlery tray
(standard depending on model)
3 Upper basket, (Design varies
according to model, and may not
match the one shown)
4 Water duct for middle spray arm
5 Middle spray arm
6 Water hardness selector
7 Lower spray arm
8 Four height adjustable screw feet
9 Filter combination
10 Salt reservoir
11 Dual compartment detergent
dispenser
12 Rinse aid reservoir
(with dosage selector)
13 Data plate
14 Indicator lights
15 Door opener
16 Child safety lock
17 Temperature selector
18 Programme selector switch
Guide to the appliance
5
Warning and safety instructions
This appliance conforms to current
safety requirements. Inappropriate
use can however lead to personal
injury and damage to property.
Read the operating instructions
carefully before starting to use this
machine. This way you will avoid
the risk of accidents, and damage
to the machine. Keep these instruc-
tions in a safe place for reference,
and pass them on to any future user.
Appropriate usage
This dishwasher is intended exclu-
sively for cleaning domestic croc-
kery and cutlery. Do not use for pur-
poses other than those for which it was
designed. Unauthorised use could
prove dangerous.
The manufacturer cannot be held re-
sponsible for any damage caused by
improper use or for uses other than
those for which the appliance is in-
tended.
The following notes are to help avoid
personal injury
To ensure stability integrated and
built-under models must be in-
stalled under a continuous worktop
which has been firmly screwed to
neighbouring units.
The electrical safety of this ap-
pliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system. It is imperative that this basic
safety requirement is tested and where
there is any doubt the electrical system
in the house is checked out by a quali-
fied electrician. The manufacturer can-
not be held responsible for damage
caused by the lack or inadequacy of
an effective earthing system, (electric
shock for example).
For safety reasons do not operate
this appliance on an extension
cable. Danger of overheating.
A damaged appliance is dangerous.
Switch off at the mains and call the
Service Department for assistance.
Repairs may only be carried out by
suitably qualified and competent
engineers to ensure safety. Repairs by
unqualified persons could be dan-
gerous.
With the "Waterproof system", the
plastic housing of the water inlet
connection contains an electrical com-
ponent. It must not be dipped in water.
Do not let small children play with
the dishwasher and its controls or
operate it.
There is a danger that children playing
might shut themselves in the dish-
washer. Please supervise its use by the
elderly or infirm.
Do not use solvents in the dish-
washer. Danger of explosion!
Avoid inhalation of powder deter-
gents.
For appliances with the heating ele-
ment in the wash cabinet do not
touch the element during or directly
after the end of a programme, you
could burn yourself.
Warning and safety instructions
6
Dishwasher detergents contain irri-
tant or corrosive ingredients. They
can cause burning in the mouth and
throat if swallowed, or inhibit breathing.
Keep children away from detergents
and from the dishwasher when the
door is open. There could be deter-
gent residues in the appliance.
To avoid the danger of children
coming into contact with the dish-
washer detergent: Only put it into the
detergent dispenser
just before starting
the programme, and then secure the
door with the child safety lock.
For models with "Delay Start" option
make sure the detergent dispenser is
dry before putting in detergent. Wipe
dry if necessary. Detergent will clog if
poured into a damp dispenser and may
not be thoroughly dispensed. If the
door is open at the end of a pro-
gramme, children may come into con-
tact with this residue.
Water in the dishwasher must not
be used as drinking water.
Appliances with a cutlery basket:
items of cutlery are cleaned and
dried more efficiently if placed in the
basket handles downwards. You may
however, prefer to place cutlery with
sharp points with the handles upwards.
Always disconnect the appliance
from the electrical supply for main-
tenance work (switch off at wall socket
and remove plug, screw out fuse in
countries where this is applicable).
The following notes should help to
avoid material damage
The voltage and frequency shown
on the data plate must match the
mains supply in the house.
Only use detergents formulated for
domestic dishwashers. Do not use
washing-up liquid.
Do not use commercial or indus-
trial detergents as these may dam-
age material and there is a risk of
severe chemical reaction.
Inadvertently filling the salt reser-
voir with dishwasher detergent al-
ways leads to damage to the water sof-
tener. Make sure that you have picked
up the right packet of dishwasher salt
before filling the salt reservoir.
Inadvertently filling the rinse aid
reservoir with powder or liquid
detergent always leads to serious dam-
age to the reservoir. Only use rinse aid
formulated for domestic dishwashers.
Do not sit or lean on the opened
door. This could cause the dish-
washer to tip and be damaged.
If your dishwasher has the heating
element visible in the base of the
wash cabinet, as far as possible al-
ways place plastic items in the top bas-
ket, and ensure they do not drop
through. The plastic could melt or lose
its shape near the heating element.
Warning and safety instructions
7
The Miele Waterproof System of-
fers protection from water damage,
provided the following conditions are
met:
the dishwasher is correctly installed
and plumbed in
the dishwasher is properly main-
tained and parts are replaced where
it can be seen that this is necessary
the stopcock has been turned off
when the machine is not used for a
longer period of time (e.g. during
holidays).
In countries where there are areas
which may be subject to infesta-
tion by cockroaches or other vermin,
pay particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any dam-
age which may be caused by cock-
roaches or other vermin will not be
covered by the appliance guarantee.
Disposal of your old machine
When disposing of an old dish-
washer first make it unusable. Dis-
connect, cut off the cable and the plug
from the cable.
Make the door lock inoperative, so that
children cannot accidentally shut them-
selves in. Make appropriate arrange-
ments for the safe disposal of the ap-
pliance.
The manufacturer can not be held
responsible for any damage caused
by non-observance of the Warning
and Safety instructions.
Warning and safety instructions
8
Caring for the environment
Disposal of the packing material
The transport and protective packing
has been selected from materials
which are environmentally friendly for
disposal and can normally be recycled.
Rather than just throwing these ma-
terials away, please ensure they are of-
fered for recycling.
Disposal of your old machine
Old machines contain materials which
can be re-cycled. Please contact your
local authorities or scrap merchant
about potential recycling schemes, be-
fore disposing of the appliance.
Energy saving washing
These dishwashers are exceptionally ef-
ficient in their use of water and elec-
tricity. You can make the most of your
appliance by following these tips:
If your household water system is
suitable, this dishwasher can be con-
nected to a hot water supply, for fur-
ther economies.
However, if your water is heated by
electricity we would still recommend
connection to cold water.
In the UNIVERSAL 55° programme,
depending on the capacity of the
dishwasher, when connected to hot
water at 55°C up to 0.7 kWh of elec-
trical energy is saved. The hot water
provides this energy, and the ap-
prox. 0.13 l oil or 0.14 m
3
natural gas
needed to heat the water might be
considerably more cost effective.
Although all stages of the wash then
take place with hot water, savings
are made in cost, time and energy.
Make full use of the baskets without
overloading the dishwasher for most
economical washing.
Choose the programme to suit the
type of crockery being washed and
the degree of soiling.
If baskets are only half full use the
ECONOMY programme.
Use the correct dosages of deter-
gent.
Caring for the environment
9
Before using for the first time
Before using for the first time please
note the following points:
See the relevant chapters for detailed
information on the points below.
Setting the water softener
The water softener unit must be set to
deal with the water hardness level in
your area.
The salt reservoir must also
first be
filled with water and then with dish-
washer salt. Never fill with dishwasher
powder detergent.
Filling the salt reservoir with deter-
gent by mistake will cause serious
damage to the water softener.
Please check every time before re-
filling that the package contains
dishwasher salt.
Add rinse aid
Inadvertently filling the rinse aid reser-
voir with powder or liquid detergent, or
washing up liquid, will cause serious
damage to the reservoir.
Only use rinse aid formulated for do-
mestic dishwashers.
Do not use washing up liquid
Only use detergent formulated for do-
mestic dishwashers.
Load the crockery correctly
Load the crockery so that water will
come into contact with all surfaces.
This ensures that they will be properly
cleaned.
The spray arms must not be blocked
by items which are too tall for the bas-
ket or which hang through. If necessary
manually rotate the spray arms to test.
Add the correct amount of detergent
Follow the detergent manufacturers
recommendations on how much deter-
gent to use. Not using enough will lead
to poor wash results. The amount to dis-
pense will depend on the type of deter-
gent and programme selected.
Read the notes on dosage given in the
programme chart.
Cleaning results may vary from brand
to brand. If you are not satisfied with
the results from one brand try another
quality brand before contacting the
Customer Service department for ad-
vice.
It is important to choose the correct
programme
The UNIVERSAL programmes are
ideally suited to everyday loads. See
the programme chart for descriptions
of other programmes.
The filter combination in the base of
the wash cabinet and the spray arms
must be kept clean.
These should be regularly inspected
and cleaned if necessary.
Before using for the first time
10
Opening and closing the door
To open the door
Press the release catch inside the
door grip.
If the door is opened during operation
all functions are automatically inter-
rupted.
To close the door
Push the baskets right in
Lift the door upwards and push until
it clicks into position
Child safety lock
The child safety lock is designed to
deter children from opening the dish-
washer door.
Use the key provided to turn the
child safety lock to the required set-
ting.
Horizontal setting = The door is
locked.
Vertical setting = The door can
be opened.
Opening and closing the door
11
Water softener
It is not necessary to reactivate with
salt if the degree of hardness in the
local supply is permanently
under
70 mg/l, (0.7 mmol/l, or 4 °d German
scale).
Your local water supplier will advise
you on the water hardness of your area.
Above 70 mg/l (0.7 mmol/l, or 4 °d Ger-
man scale) water must be softened.
This is to avoid the build-up of calcium
deposits on crockery and cutlery, and
in the dishwasher, and also to increase
the effectiveness of the detergent.
To ensure a steady supply of soft water
the built-in water softener must be:
1. correctly set and
2. the salt reservoir must be filled with
dishwasher salt for reactivation.
The dishwasher is set at the factory to
operate to a hardness level of
400 - 630 mg/l (4.0 - 6.3 mmol/l, or 22 -
35 °d German scale).
If your water is harder or softer than
this the factory setting will need to
be adjusted.
Setting the water hardness level
selector in the wash cabinet
There are six settings on the selector.
Setting °d mg/l °f
1 4-14 70-250 7-25
2 15-21 270-380 27-38
3* 22-35 400-630 40-63
4 36-47 650-850 65-85
5 48-65 860-1170 86-117
6 66-70 1190-1260 119-126
* factory setting
Use a coin or screwdriver to adjust
the water hardness level selector in
the wash cabinet. There is a click as
each setting is reached.
Example:
The water hardness level is 320 mg/l.
The water hardness level selector must
be set to setting 2, 270 - 380 mg/l
(15 - 21 °d German scale).
Water softener
12
Filling the salt reservoir
Please only use special coarse grained
dishwasher salt for reactivation, as
other salts may contain insoluble addi-
tives which can impair the functioning
of the softener.
The salt reservoir holds approx. 2 kg of
salt.
Inadvertently filling the salt reservoir
with
dishwasher detergent always
causes serious
damage to the
water softener.
Make sure that you have picked up
the right packet of
dishwasher salt
before filling the salt reservoir.
Remove the bottom basket.
Unscrew the salt reservoir cap.
Before filling the salt reservoir for
the first time:
Fill the salt reservoir with approx.
2 litres of water.
Place the funnel (provided) in place.
Fill carefully with salt
(As it is filled displaced water will run
out).
Clean salt from the screw threads of
the socket.
Screw the cap on firmly.
Run the COLD PRE-WASH pro-
gramme
immediately to remove any
traces of salt water from the cabinet.
This is not necessary if a UNIVER-
SAL or UNIVERSAL PLUS pro-
gramme is run straight away.
Water softener
13
Salt indicator
When the salt reservoir is empty the
Salt indicator light comes on. The
reservoir should be refilled with dish-
washer salt for reactivation.
Note
With very soft water, i.e. constantly at a
level below 70 mg/l (4 °d), the reservoir
does not have to be filled with salt and
although the salt light does come on,
this can be disregarded.
Water softener
14
Adding rinse aid
Rinse aid is necessary to ensure that
water does not cling and leave marks
on crockery during the drying phase.
Rinse aid is poured into the storage
reservoir and the amount set is dis-
pensed automatically.
The rinse aid reservoir holds approx.
130 cm
3
.
Inadvertently filling the rinse aid
reservoir with
powder detergent (or
liquid detergent) always causes
serious damage to the reservoir.
Only pour
rinse aid formulated for
domestic dishwashers into the reser-
voir.
Although it is possible to use
house-
hold vinegar with a max. 5% acid
content, or liquid citric acid up to
50% acid as an alternative, the re-
sulting rinsing and drying quality
will not be as good as when rinse
aid is used.
Do not use vinegar with a high acid
content (e.g. vinegar essence 25%
acid). This must
not be used as its
use would damage the dishwasher.
Add rinse aid when the indicator
light Rinse aid on the control panel
comes on.
Press the button (in the direction of
the arrow) until the flap springs open.
Adding rinse aid
15
Add rinse aid only until it is visible on
the surface of the filter in the open-
ing.
Close the flap firmly.
The flap must audibly engage, other-
wise water could get into the rinse
aid storage container during the pro-
gramme.
Mop up any split rinse aid. This pre-
vents over-forming occuring during
the next programme.
The flap should normally remain
closed. Only open it for adding more
rinse aid!
Wait until the Rinse aid indicator on
the control panel lights up before ad-
ding more rinse aid.
Setting the dosage
The dosage adjuster (see arrow) in the
opening has settings from 1 to 6. It is
set to 3 at the factory, as the recom-
mended dose.This setting dispenses
approx. 3 ml rinse aid per programme.
If there are flecks on glasses after
drying use a higher setting.
If smearing appears on crockery use
a lower setting.
Adding rinse aid
16
Loading the dishwasher
Note
Load the crockery so that water will
come into contact with all surfaces.
This ensures that they will be
properly cleaned.
Do not place crockery and cutlery in-
side other pieces where they may be
concealed.
Hollow items e.g. cups, glasses etc.
must be inverted in the basket.
Deep based items should be placed
at an angle such that water runs off
them freely.
Tall narrow hollow pieces should be
placed in the centre of the basket,
rather than in the corners, to ensure
good coverage of water.
Small pieces should be placed on the
cup racks. Cups should be on the
lower rack and bowls on the top rack
so that water reaches all pieces.
The spray arms must not be blocked
by items which are too tall for the
basket or which hang through.
If necessary manually rotate the
arms to test.
Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or ket-
chup. Plastic items in the dish-
washer may discolour if large quan-
tities of these foodstuffs find their
way into the appliance on the croc-
kery.
The stability of the plastic items is
not affected by this discolouration.
Loading the dishwasher
17
Loading examples
Upper basket
Small, lightweight, delicate items such
as cups, saucers, glasses, dessert
bowls, etc.
Bottom basket
Larger and heavier items such as
plates, serving platters, saucepans,
bowls. Depending on the dishwasher
model glasses may only be cleaned in
the bottom basket if it is fitted with a
special glassware insert or if there is a
special bottom basket.
Dishwashers with cutlery tray
Dishwashers with cutlery basket
Loading the dishwasher
18
Cutlery
Dishwashers with cutlery basket:
Unsorted cutlery should be placed in
the cutlery basket, handles facing
downwards.
You may, however, prefer to place
cutlery with sharp points with the
handles upwards.
Place small spoons in the individual
slots to either side of the cutlery basket.
Larger items like soup ladles, long
knives and mixing spoons should be
placed lying down across the front of
the upper basket.
Loading the dishwasher
19
Dishwasher with cutlery tray
(SC models):
For best results cutlery should be
grouped in zones, one for knives, one
for forks, one for spoons etc. This
makes unloading much easier.
Larger items like sauce ladles, cake
slices, long knives and mixing spoons
can be placed lengthwise in the trough
in the centre of the tray.
The cutlery tray insert is removable. It
can be completely removed from its
frame and carried to the cutlery drawer,
or table where it can be easily un-
loaded.
Loading the dishwasher
20
Spoon heads should be placed in such
a way that water runs off them freely.
Cutlery with round or oval handles
should be placed with the heads in the
grips as this prevents them slipping.
Ensure that spoon heads are in contact
with at least one of the grips in the cut-
lery tray. This way they cannot collect
water.
The upper spray arm must not be
blocked by items which are too big,
e.g. cake slices.
Loading the dishwasher
21
Flap up racks
Can either be used for a second row of
cups or raised upwards to make room
for tall items.
Positioning rail
(standard feature depending on model)
For easy sorting and removing of croc-
kery the positioning rail can be rested to
one side.
Raise it again afterwards so that croc-
kery can rest against it in the basket.
Loading the dishwasher
22
Adjusting the upper basket
(depending on model)
In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted in three steps with 2 cm be-
tween each step.
Pull out the upper basket and loosen
the two locknuts on either side of the
basket.
Adjust the basket up or down to the
right height.
Tighten the locknuts.
The upper basket can also be set to an
angle if required.
Depending on the setting of the upper
basket the following dimensions can be
accommodated:
Dishwashers with cutlery tray
Upper
basket
position
plates Ø in cm
Upper
basket
Lower
basket
Top 15.5 30
Middle 17.5 28
Bottom 19.5 26
Dishwashers with cutlery basket
models with adjustable upper basket
Upper
basket
position
plates Ø in cm
Upper
basket
Lower
basket
Top 21.5 30
Middle 23.5 28
Bottom 25.5 26
models with non-adjustable basket
Plate Ø in upper basket: 23.5 cm
Plate Ø in lower basket: 28 cm
Loading the dishwasher
23
Items not suitable for dishwashers
cutlery with wooden or horn handles,
wooden or plastic chopping boards,
glued items, e.g. old knives with
handles which have been glued on,
hand-made craft items,
copper or tin items,
plastic items which are not heat resis-
tant.
Please note
Silver- and aluminium items can suf-
fer some discolouration.
Aluminium components (e.g. grease
filter) must not be cleaned with caus-
tic alkaline commercial or industrial
detergents. This may damage ma-
terial or, in extreme cases, cause
severe chemical reaction.
Silver, treated with a silver polish
may still be damp or spotted at the
end of a programme, where water
has not run off smoothly. It may need
rubbing dry with a soft cloth.
Silver,
treated in a
silver immersion dip is
usually dry at the end of a pro-
gramme but may discolour.
Colours painted over a glaze may
fade after many washes.
Clouding may occur on
glasses after
frequent washing.
We recommend:
Wash delicate glassware in the
ECONOMY 55 ° - programme, (or for
models where the programme is
available, GENTLE 45°C). This will re-
duce the risk of clouding.
There are no standard guidelines for
washing glassware. When in doubt
wash by hand.
When purchasing new crockery and
cutlery, make sure they are dish-
washer safe.
Items not suitable for dishwashers
24
Adding detergent
Only use detergents formulated for
domestic dishwashers. Do not use
washing up liquid.
Please note
Dishwasher detergents contain irri-
tant or corrosive ingredients. They
can cause burning in the mouth
and throat if swallowed, or inhibit
breathing. Keep children away from
detergent and from the dishwasher
when the door is open. There could
still be detergent residues in the
cabinet.
To avoid the danger of children com-
ing into contact with the dishwasher
detergent:
only put it into the detergent dispen-
ser just before starting the pro-
gramme.
Selecting detergent
Recently almost all detergent manufac-
turers have launched
new detergents
with a different composition, in addition
to standard types.
Should you experience difficulties when
using these types of products, please
contact Miele Customer and Technical
Services Department, or the detergent
manufacturers own Advisory Service.
These
new dishwashing detergents, al-
though welcome from an ecological
point of view, react to a different degree
from conventional products to water
hardness. The drawbacks may only
become apparent after a prolonged
period of use.
The following problems may occur:
White deposits on crockery and
inner cabinet.
Increased etching in the form of a
bluish sheen on the surface of glass-
ware.
Discolouration of silverware.
Appearances of this nature are
generally caused by the detergent
used and are not attributable to any
malfunctioning of the dishwasher it-
self.
Adding detergent
25
Preventive measures:
1. If you wish to continue using the new
chlorine and phosphate-free pro-
ducts, the following is recommended:
Set the water hardness selector one
setting higher than recommended in
the Water softener chapter, if the
water hardness is at the top of the
scale (except with setting 6).
Example:
above 610 mg/l (34 °d ) set the
water hardness selector to setting 4.
Try out an environmentally friendly
detergent of the same type from an-
other manufacturer.
2. If you are still dissatisfied with the re-
sults, we recommend the use of
chlorine-free but not phosphate-free
detergent.
Set the water softener and dispense
detergent according to instructions
given in this instruction booklet.
3. If results are still not to your satisfac-
tion, you should revert back to using
conventional
detergents containing
both chlorine and phosphate.
Set the water softener and dispense
detergent according to instructions
given in this instruction booklet.
Should you experience difficulties when
using these types of products, please
contact the detergent manufacturers
own Advisory Service.
Adding detergent
26
Dishwasher detergent must be added
before each programme (except COLD
PRE-WASH).
Pour powder or liquid detergent into
the dispenser.
Dishwasher detergent tablets can be
put at various places in the wash
cabinet, (follow the manufacturers
advice on the packet).
Detergent manufacturers give the re-
quired amount of detergent in ml (or g)
on the packaging.
For UNIVERSAL programmes use at
least 30 ml (or g) detergent unless ad-
vised to use more by the manufacturer,
then use what they advise.
The amount to dispense will depend on
the type of load and the programme se-
lected.
See the programme chart on the next
pages for advice on amounts to dis-
pense.
If you buy detergent in bulk please
ensure that the container is always
properly sealed after use. Otherwise
the detergent can lose its effective-
ness.
Adding detergent
27
For information:
Compartment I takes max. 25 ml, Com-
partment II max. 80 ml. There are hori-
zontal markers to assist with
dispensing in compartment II, indicat-
ing the level in ml.
Press the opening catch on the con-
tainer flap.
The flap will spring open.
The flap is always open at the end of a
programme.
Pour in the required amount of deter-
gent.
Shut the flap.
Adding detergent
28
Programme selection
Choose your programme according to
the type of load and how dirty it is.
In most cases this will be a UNIVER-
SAL - programme.
UNIVERSAL 55 ° or 65 °
(with one pre-wash) or
UNIVERSAL PLUS 55 ° or 65 °
(with two pre-washes).
These programmes are ideally suited to
everyday loads, mixed loads with va-
rying degrees of soiling.
For particular needs there are special
programmes:
The different programmes and their
uses are described on the next two
pages in the Programme chart.
Programme selection
29
Programme chart
Programme When to use Detergent
A
1)
B
2)
Compart-
ment
I
(Pre-wash)
Compart-
ment
II
(Wash
cycle)
Compart-
ment
II
(Wash
cycle)
Universal Programmes
UNIVERSAL
55 °
3)
This programme is for
normal everyday
loads
20 % 80% 100 %
UNIVERSAL
65 °
as UNIVERSAL 55 °, but higher
temperatures for
stubborn dried on
particles
20 % 80 % 100 %
UNIVERSAL
PLUS 55 °
as UNIVERSAL 55 °, but with preliminary
pre-wash for
heavy soiling
20 % 80 % 100 %
UNIVERSAL
PLUS 65 °
as UNIVERSAL PLUS 55 °, but higher wash
temperature for
stubborn dried on particles
and lightly soiled pots and pans
20 % 80 % 100 %
Special programmes
ECONOMY
55 °
for full loads with very light soiling, e.g.
coffee cups, or:
for
half a, normal everyday load
50 % 50 %
COLD
4)
PRE-WASH
for rinsing crockery to avoid smells if a
complete cycle is not needed
The amount dispensed will depend on the type of detergent being used:
A
1)
Use this method for:
detergents which contain phosphates and chlorine (except liquid detergent)
Divide the total amount proportionally between compartment I and compartment II.
B
2)
Use this method for:
detergent which is chlorine and phosphate free
detergent which is chlorine free but contains phosphates
liquid detergent
In this instance the whole amount is placed in compartment II.
For UNIVERSAL programmes use at least 30 ml (or g) detergent unless advised to use more by the
manufacturer, then use what they advise.
3) Standard programme (see chapter Comparison tests)
4) See Section "Plumbing"-Connection to the water inlet.
Programme chart
30
Programme cycle Consumption Time
Energy kWh Water Minutes
(approx.)
1.
Preliminary
pre-wash
2.
Pre-wash
Main
wash
Interim-
rinse
Final
rinse
Drying-
phase
Water
cold
(15 °C)
Water
hot
(55 °C)
Litres Water
cold
(15 °C)
Water
hot
(55 °C)
XX
55 °
XX
65 °
X1.30.6208370
XX
65 °
XX
65 °
X1.40.7208672
X
XX
55 °
XX
65 °
X1.50.5259075
X
XX
65 °
XX
65 °
X1.60.7259478
X
55 °
XX
65 °
X 1.2
5)
0.4
5)
16 68
5)
58
5)
X
0.06 0.06 5 8 8
5) with half loads (6 place settings)
31
Switching on and off
Switching on
Close the door
Open the stopcock (if it is closed).
Turn the Programme selector switch
(programme sequence indicator)
clockwise, until a resistance is felt, to
the start point of the required pro-
gramme, e.g. "UNIVERSAL PLUS".
Then turn the Temperature selector
switch to the required temperature
e.g. 65 °”.
The programme cycle begins.
If you turn the selector past the
start point by mistake:
Turn the temperature selector switch
to 0-Off.
Turn the programme selector switch
in a clockwise direction to the re-
quired start point.
Re-set the temperature with the tem-
perature selector switch.
Programme change
It is possible to change temperature
within a programme, e.g. UNIVER-
SAL 55 ° to UNIVERSAL 65 °.
If changing a programme, e.g.
UNIVERSAL PLUS to UNIVERSAL it
is advisable to first turn the dish-
washer off.
Switching off
On completion of a programme:
Turn the temperature selector to
0-Off.
If the dishwasher is not to be used for a
longer period of time, e.g. whilst on holi-
day:
Turn off the stopcock.
Switching on and off
32
Programme sequence indication
During the programme the programme
selector switch moves around the dial
to show which stage has been reached:
Pre-wash (not shown)
Wash cycle
Interim rinse
Final rinse
Drying phase
The programme selector switch re-
mains stationary during the warm-up
phases of the wash and rinse cycle
until the required temperature has been
reached.
Note!
Do not finish a programme prematurely.
Important programme stages (e.g. re-
activating the water softener) could be
omitted.
A programme is complete only when
the programme selector switch is at the
"End" position.
The dishwasher can be opened and
crockery unloaded. If it is left closed,
the fan will continue for a few more
minutes to diminish any remaining mois-
ture.
This is recommended if the crockery is
not required immediately. This process
is extra to the wash programme.
The COLD PRE-WASH programme is
complete only when the programme se-
lector switch stops just before the start
point of the UNIVERSAL PLUS pro-
gramme.
Programme interruption
A programme is interrupted as soon as
the door is opened.
If the door is closed again the pro-
gramme will continue from the position
it was at when it was interrupted.
Warning
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise caution
when doing so.
Before closing the door leave it ajar
for approx. 20 secs. This will en-
able the temperature in the wash
cabinet to settle. Close the door
firmly making sure that it clicks into
place.
Switching on and off
33
Remove load
Hot crockery will chip and break
more easily.
After switching off let it cool down in
the dishwasher until it is comfortable
enough to handle, before you unload
it.
If you open the door fully after switch-
ing off, the crockery will cool down
much faster.
First unload the bottom basket, then
the upper basket and then the cut-
lery tray (if you have one) at the very
end.
This way you avoid water droplets
from the upper basket or the cutlery
tray falling on to crockery in the bot-
tom basket.
Remove load
34
Cleaning and care
Cleaning the filters in the wash
cabinet
The dishwasher must not be used
without all the filters in place!
The filter combination in the base of the
wash cabinet should be regularly in-
spected and cleaned if necessary.
Turn the handle anti-clockwise to re-
lease the filters.
Lift and take the filter combination out
of the machine. Remove coarse par-
ticles and rinse under running water.
Use a nylon brush if necessary.
Cleaning and care
35
Cleaning and care
Turn the filter combination over and
open the coarse filter by pulling
back on the locking device.
Clean the coarse filter under running
water, using a brush if necessary,
and press the locking device back in.
Important:
After cleaning make sure that the lock-
ing device is properly locked.
Replace the filter combination so
that it lies flat in the base of the wash
cabinet. Secure the filter by turning
the handle in a clockwise direction.
Cleaning and care
36
Cleaning and care
Cleaning the spray arms
Particles of food can lodge in the spray
arm jets.
The spray arms should be inspected
and cleaned regularly (approx. every 6
months).
To do this remove the spray arms as fol-
lows.
Lift up the middle spray arm b to en-
gage the tooth-wheel mechanism.
Then unscrew the spray arm
c.
Remove the lower basket and take
out the
lower spray arm.
Dishwashers with cutlery basket:
Unscrew the upper spray arm.
Dishwashers with cutlery tray:
Pull out the cutlery tray.
Lift up the upper spray arm to en-
gage the tooth-wheel mechanism
and then unscrew the spray arm.
Using a sharp pointed object push
the food particles into the spray arm
jets and rinse well under running
water.
Please note:
After replacing the spray arms check
that they move freely.
Cleaning and care
37
Cleaning and care
Cleaning the drain pump and
non-return valve
If water has not been pumped away at
the end of a programme the drain
pump or the non-return valve might be
blocked. They are, however, easy to
clean. Watch out for glass splinters,
which could cause injury.
Take the filter combination out of the
wash cabinet.
Use a jug or bowl to scoop water out
of the wash cabinet.
Raise the locking clamp.
Lift up the non-return valve and rinse
under running water.
The drain pump is situated under the
non-return valve (see arrow).
Before replacing the non-return valve
check that the drain pump impeller
turns with only slight resistance, and
that there is no obstruction.
Carefully replace the non-return
valve and secure with the locking
clamp.
Replace and secure the filter combi-
nation.
Cleaning and care
38
Cleaning and care
Cleaning the filter in the water
inlet
A filter is incorporated in the screw con-
nection of the valve on the water inlet
hose. The filter must be cleaned when
dirty, otherwise insufficient water flows
into the wash cabinet.
The plastic housing of the water
connection contains an electrical
component. It must not be dipped
in water.
Fitting an in-line water filter
If the mains water contains a large num-
ber of insoluble substances, we recom-
mend fitting a large area filter in the
connection between the stopcock and
the water inlet hose threaded union.
These filters can be obtained from the
Miele Spares Department (Part No.:
75577).
To clean the filter
Disconnect the appliance from the
mains supply (switch off at the main
socket and pull out the plug, switch
off the appropriate circuit at the fuse-
box or withdraw the mains fuse).
Turn off the stopcock and unscrew
the inlet hose.
Carefully remove the rubber seal.
Withdraw the filter using pointed
pliers and clean by rinsing under run-
ning water.
Replace filter and seal. Make sure
they are sitting correctly!
Screw back into place on the water
inlet, taking care that it goes back on
straight.
Turn on the stopcock gradually to
test for leaks.
If there is a leak:
Screw the connections on more
tightly.
Cleaning and care
39
Cleaning and care
Cleaning the wash cabinet
In general the wash cabinet is self-
cleaning, provided that the correct
amount of dishwasher detergent is
used.
If however ther are time scale or grease
deposits these can be removed with a
proprietary dishwasher cleaner.
Cleaning the door and the
door seal
Wipe the door seal regularly with a
damp cloth and remove any par-
ticles of food.
Wipe away any residue of food and
drink spillage from the sides of the
dishwasher door. These are not part
of the wash cabinet and are not
reached by water from the spray
arms.
The facia panel
This should only be wiped with a
damp cloth, or a suitable plastic
cleaner.
Do not use an abrasive cleaner, a
glass cleaner or an all-purpose
cleaner. Because of their chemical
composition they could cause
serious damage to plastic surfaces.
The front of the dishwasher
Laminate fronts should be cleaned
using a suitable proprietary cleaning
agent.
Fronts made from wood should only
be cleaned using a damp cloth or
leather and dried with a soft cloth.
Do not use any cleaner containing
ammonia or thinners.
Cleaning and care
40
Checking the water level
Checking the water level
If the water pressure (flow rate at the
take-off point) is too low, i.e. less than
1,0 bar, too little water will flow into the
wash cabinet.
To ensure an accurate assessment
open the stopcock fully and run the
COLD PRE-WASH programme once
(without crockery) to bring water into
the system.
Run the COLD PRE-WASH pro-
gramme again. After approx. 3
minutes open the door and remove
the bottom basket from the machine.
The water level is correct when dimen-
sion X is at least 4 mm.
If it measures less, then the water in-
take time must be increased.
Checking the water level
41
Increasing the water intake
time
Position the right hand switch verti-
cally and then pull it off.
Using a 4-5 mm wide screwdriver
turn the adjuster mechanism to the
right hand side of the spindle
carefully in an anti-clockwise direc-
tion until it checks into position.
= Anti-clockwise turn (increases
water intake 2 min.)
= Clockwise turn (factory
setting 1 min.)
Note:
If the water intake time has been in-
creased, then the water hardness selec-
tor must be reset at one grade higher
than that stated in chapter Water sof-
tener (except with setting 6).
Checking the water level
42
Problem solving guide
With the aid of the following explana-
tory notes, minor faults can be cor-
rected without contacting the Miele Ser-
vice Department.
Any work on the electrical compo-
nents of the appliance should only
be carried out by a suitably quali-
fied and competent person in ac-
cordance with local and national
regulations. Unauthorised repairs
could be dangerous.
Faults/possible causes
The dishwasher does not start
The door is not properly closed.
The plug is not properly inserted.
The fuse is defective/has blown.
The dishes are not clean
The dishes are incorrectly loaded.
The wrong amount of detergent was
used.
The stopcock was not fully opened.
The water pressure is too low (too
little water in the wash cabinet) see
chapter Checking the water level.
The filter in the water inlet screw con-
nection is blocked - see Cleaning
and care.
The filters in the wash cabinet are
not clean - see Cleaning and care.
Spray arm jets are blocked - see
Cleaning and care.
The spray arms are obstructed by
items in the baskets.
White residue on cutlery and
crockery
Not enough rinse aid.
No salt in the salt reservoir.
Salt reservoir lid has not been
screwed on properly.
Water in the wash cabinet at the end
of a programme
The drain hose is kinked.
The drain pump or non-return valve
may be blocked. See Cleaning and
care.
After Sales Service
Should you still have any difficulties,
or if the appliance is under guaran-
tee please contact:
your Miele Dealer or
the Miele Service Department
See back cover for addresses.
Please quote the model type and
number of your appliance. This infor-
mation can be found on the data
plate inside the door.
Problem solving guide
43
Special accessories
Bottle holder
(depending on model)
The bottle holder (e.g. for milk or baby
bottles) can be used in the bottom bas-
ket.
To achieve good cleaning results the
bottle holder should only be placed in
the positions marked white
and on no
account in the positions marked with
an X.
Other special accessories e.g. special
inserts for glasses or plates, etc. are
available through your Dealer or the
Spare Parts Department.
See the following list.
Installation - special situations
Brackets to fix the dishwasher under a
marble-type worktop.
Decor frame for freestanding dish-
washers (GDR) to match kitchen fronts
in colour and style, (available with
some models).
Decor frame adapter strip for free-
standing dishwashers for decor pa-
nels 1 to 4 mm thick.
Building-under kit (GDU) to modify an
integrated i dishwasher to a built-
under dishwasher.
Extended machine feet where a
height of up to 92 cm is required.
Plinth facia kit for "i" dishwashers for
kitchens without a complete plinth facia
run.
Adapter strips for "i" dishwashers to
match the control panel facia to the ad-
jacent drawers.
Inserts
Glass inserts for the bottom basket,
(only available for models with remov-
able inserts in the bottom basket).
Glass inserts for the upper basket,
especially for glasses which need a
special support.
Special accessories
44
Comparison tests
Test standard: IEC 436 / DIN 44990 / IEC 704 / prEN 50242
Programme tested: UNIVERSAL 55 °
Amount of detergent: If using a detergent containing chlorine:
5 g in compartment I, 25 g in compartment II.
If using a chlorine-free detergent:
30 g
only in compartment II.
Rinse aid dispensing: Setting 3, (approx. 3 ml, set at factory)
Noise measurement: Before starting a programme to measure noise, the
dishwasher door must first be opened completely.
Doing this will automatically close the vent exit for
the turbothermic drying process as in daily use.
Amount washed: 12 place settings
Dishwasher with cutlery basket
Upper basket
Lower basket
These illustrations show how 12 place settings can be loaded. For normal mixed
loads see Loading the dishwasher.
Comparison tests
45
Dishwasher with cutlery tray
Upper basket
Cutlery tray
Lower basket
Comparison tests
46
Installation instructions
47
Contents
Installing a freestanding dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Installation integrated "i" dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
1. Fit worktop protection ("niro" stainless steel coverplate) . . . . . . . . . . . . . . . . . . 51
2. Building the dishwasher into a niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3. Fitting the facia panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4. Matching the facia panel to the dimensions of the adjacent drawer fronts . . . . . . 56
5. Fitting the (matching) door front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6. Adjusting the door springs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7. Levelling and securing the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
8. Matching the plinth facia of a kitchen run. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Connection to the water inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Contents
48
Installing Freestanding dishwashers
Freestanding dishwashers
The dishwasher must be installed
and levelled.
Any unevenness in the floor level
can be compensated for by adjust-
ing the four screw feet.
The adjustment range is approx. 1 cm
(85-86 cm total height).
Decor frame and decor panel
Freestanding dishwashers can be
subsequently fitted with a decor frame
(standard feature with some models
only).
This enables the front of the dish-
washer to be fitted with a decor panel
to match the kitchen furniture.
Decor panels up to 1 mm thick:
Decor panel dimensions:
587 x 603 x 1 mm.
Decor panels up 1 to 4 mm thick:
Decor panel dimensions:
587 x 599 x 1 - 4 mm
With decor panels 1 to 4 mm thick, an
extra decor frame adapter strip (spe-
cial accessory) must be fitted to the
control facia panel.
Screw on the lower decor strip b.
Insert the decor panel c.
Screw the side decor strips into posi-
tion.
Installing Freestanding dishwashers
49
Installing integrated i Dishwashers
The i model dishwashers are spe-
cially designed for building under a
continuous worktop.
The front can be fitted with a base unit
front to match the kitchen furniture.
By using a decor set GDU i model
dishwashers can be converted into a
built-under Umodel dishwasher.
The decor set is supplied with a separ-
ate installation instruction leaflet.
To ensure stability, these dish-
washers must only be installed
under a continuous worktop which
must be securely screwed to neigh-
bouring units.
Dimensions:
1) with 870 mm machine height
2) with 820 mm machine height
Range of adjustment approx. 5 cm (82-
87 cm total height).
Extended machine feet are available at
extra cost, (special accessory). These
can be used for a machine height of 87
to 92 cm.
Installing integrated i Dishwashers
50
1.Fit worktop protection
A stainless steel niro coverplate is
supplied with the machine to protect
the underside of the worktop against
steam rising from the machine.
The coverplate is supplied as standard
with "i" models.
Squeeze sealant from the tube sup-
plied
b into the angle of the niro
plate.
Align the "niro" plate c to the front
edge of the worktop - see illustration -
and then use tacks supplied to nail
the niro plate to the underside of
the worktop.
On worktops with wood or laminate
edging, the tacks should be nailed
through the holes further back from
the edge.
Installing integrated i Dishwashers
51
2.Building the dishwasher into
a niche
Connection to water and drainage
should be sited beside and not behind
the dishwasher for accessibility. Con-
nections are usually made in the area
under the sink. Many kitchen unit manu-
facturers provide a cutout in the base
of the sink base unit for the hoses to be
fed through.
If the base unit has no opening and if
there is not an opening through the plinth
area for connections, one must be cut.
Suggested dimensions: 60 x 110 mm.
For some installation steps it is
necessary to pull the dishwasher
slightly out of the recess. Therefore
do not make these connections until
last.
Installing integrated i Dishwashers
52
The slides make installation of the dish-
washer easier and protect the floor
from possible damage when moving
the appliance into and out of the re-
cess. They are also used for adjusting
the height of the rear screw feet.
Adjust the height manually before in-
stalling the dishwasher. Leave a
space of approx. 5 mm below the
worktop to allow the dishwasher to
be pushed back easily into the re-
cess. Make sure that the dishwasher
stands level.
Press the slides - with the ratchet at
the rear - under the screw feet.
Push the dishwasher right back into
the recess. Ensure that drain hose,
inlet hose and electric cable are laid
to reach the connection point without
any kinks.
Installing integrated i Dishwashers
53
Adjust the rear screw feet to the re-
quired height.
Higher = turn clockwise
Lower = turn anti-clockwise
Several turns are needed to adjust 1 mm
in height. A battery-powered screw-
driver could be used.
Adjust the front screw feet manually
or with a flat blade screwdriver.
It is easier to adjust the screw feet if the
weight of the dishwasher is not bearing
down on them.
If possible tip the machine slightly.
For fine adjustments it may be
necessary to press with a screw-
driver against the cogs of the feet.
Screw the feet out until the dishwasher
is right up against the underside of the
worktop, to which it will be screwed
later. Ensure that the dishwasher
stands level.
Installing integrated i Dishwashers
54
3. Fitting the facia panel
The facia panel is delivered separately
in the colour ordered with the relevant
accessories.
It has to be fitted to the dishwasher
when it is being installed.
Press out the adapter strips from the
fitting slits in the facia panel.
Fit the seal supplied b into the
groove surrounding the ventilation
grille
c.
Push the ventilation grille c into posi-
tion.
Place the facia panel d in position
and screw into place from the inside
of the door using the six screws
e.
Attach the switch knobs f.
Only applicable when using the GDU
decor set (to convert an "i" version to a
built-under "U" version)
If the GDU decor set is being used, the
adapter strips
g must first of all be
removed, and stored for possible use
in the future. See also the separate in-
structions for fitting the GDU decor set.
Press out the adapter strips from the
fitting slits in the facia panel.
Installing integrated i Dishwashers
55
4.Matching the facia panel to
the dimensions of the
adjacent drawer fronts
The facia panel can be aligned with the
drawer fronts of the kitchen units by ad-
justing the spacer bars.
Using an 8 mm socket spanner turn
clockwise or anti-clockwise until the
required height is reached.
If necessary some or all spacer bars
can be removed.
Adjustment range:
from 112 mm: facia panel without
spacer bars
to 145 mm: facia panel with four
spacer bars,
to 154 mm: using a fifth spacer bar
(special accessory at
extra cost).
Please note
After adjustment cut off any protruding
lengths of the screws.
Installing integrated i Dishwashers
56
5.Fitting the (matching) door
front
The door of a kitchen base unit (without
the drawer facia or fittings) is normally
used for the door front.
The door front is fixed to the machine
door outer panel using a fixing bracket
which has to be pre-mounted on the
rear of the door front.
Fixing brackets are already fitted on to
the stainless steel door front. This front
cannot be shortened.
Door fronts differ in weight and it is
therefore essential that the door
springs are adjusted (see Step 6)
after the door front has been fitted.
Calculate dimension X and make a
note of it before attaching the fixing
bracket.
Dimension X is the dimension shown
on the illustration between the drill hole
in the outer door panel and the lower
edge of the neighbouring unit door(s).
Installing integrated i Dishwashers
57
Installing integrated "i" Dishwashers
Lay the door front with the rear side
facing upwards.
Using a pencil draw a vertical line
down the middle of the door to use
as a guide line.
Draw a horizontal guide line across
the door, at a distance from the lower
edge of the front panel equalling the
previously measured dimension X .
The fixing bracket is marked in the
middle
A
.
Lay the bracket on the rear side of
the door front so that the marks
A
in
the middle of the fixing bracket align
with the vertical guide line, and the
lower fixing holes of the bracket are
centrally positioned in the horizontal
guide line (see illustration). Use
strips of adhesive tape to hold the
bracket in this position.
Drill the fixing holes to a depth of
about 10 mm, using a 2.5 mm drill bit.
Secure the bracket to the door using
the screws supplied.
Double check for correct alignment
before building into the recess.
Installing integrated i Dishwashers
58
Installation integrated i Dishwashers
Pull the dishwasher out of its recess
enough to allow easy access to the
side fixing screws for the door front.
Hang the door front into the slits in
the machine door outer panel, adjust
for height and secure.
Secure the door front by turning the
screws clockwise at each side of the
machine door outer panel.
Plug the openings for the fixing
screws using the plastic stoppers
provided.
Installing integrated i Dishwashers
59
6.Adjusting the door springs
The door springs are correctly adjusted
when a half opened door (approx. 45°
opening angle) remains in that position
when released.
If the door drops down, then the door
springs need to be tightened.
If, however, it rises up, then the springs
need to be released.
The adjusting screw is located in the
upper front strip at the left hand side of
the dishwasher.
Open the dishwasher door.
Adjust the door spring until it is cor-
rectly balanced:
turn clockwise = tighten
turn anti-clockwise = loosen.
Push the dishwasher back into its
recess.
7.Level and secure the
dishwasher
To ensure the stability of the dish-
washer it must be screwed to the con-
tinuous worktop after it has been posi-
tioned.
Half open the dishwasher door.
Screw one of the 4 x 15 screws (sup-
plied) from below into the holes in
the right and left hand side of the
upper strip.
Do not lift the dishwasher to do this.
If necessary, screw the feet out fur-
ther.
Installing integrated i Dishwashers
60
If one of the screw positions is in the
cut-out area, e.g. of the built-in sink, at-
tach the fixing bracket supplied.
Pull the dishwasher approx. 5-10 cm
out of the recess.
Position the fixing bracket.
Push the dishwasher back into the re-
cess, adjust and screw into position
with a (3.9 x 22) screw.
For Corian or granite worktops there
is a special accessory to fix the dish-
washer to an adjacent kitchen unit.
Pull the dishwasher approx. 5-10 cm
out of its niche.
Fit the lug of each fixing bracket into
the guide hole on top of the dish-
washer, and then swing to the left or
right side respectively.
Push the dishwasher back into the
niche, align, and fix to the adjacent
kitchen unit(s) with 2 screws (3.5 x 15)
for each bracket.
Installing integrated i Dishwashers
61
8.Matching the plinth facia of a
kitchen run
The plinth area of the dishwasher is nor-
mally covered with a plinth run match-
ing the kitchen furniture.
The height (H) of the plinth facia around
the dishwasher depends on the plinth
return (R) and how much the door front
extends below the dishwasher door (P).
Place the plinth facia directly in front
of the kitchen run but do not attach.
Carefully open the dishwasher door.
If the door front comes into contact with
the kitchen plinth when the dishwasher
door is opened the plinth facia in the
area around the dishwasher door
needs to be cut to size.
To do this mark where the edge of
the door front comes into contact
with the plinth facia.
Cut the plinth facia to size along this
line.
Place the plinth facia in front of the
kitchen run again and check whether
the dishwasher door can be opened
fully.
If it cannot, trim the plinth facia to the
correct size.
Secure the plinth facia to the ad-
jacent kitchen units.
If your kitchen does not have a plinth
run matching the kitchen furniture, the
plinth area can be covered with a sep-
arate plinth kit, available at extra cost.
Installing integrated i Dishwashers
62
Electrical connection
Please follow the installation instruc-
tions carefully.
This dishwasher is supplied ready
for connection to an a.c. single
phase supply, (230 - 240 V 50 Hz for
the UK and Australia). It is supplied
with a mains cable and moulded
plug.
All electrical work should be carried
out by a competent person in ac-
cordance with national and local
regulations. Connection should be
made via a fused plug and suitable
switched socket which is easily ac-
cessible.
For extra safety it is advisable to in-
stall a residual current device (RCD)
with a trip current of 30 mA.
The voltage, rated load and fuse
rating are given on the data plate.
Please ensure that these match the
household mains supply.
Important
The wires in the mains lead are col-
oured in accordance with the following
code:
Green/yellow = earth
Blue = neutral
Brown = live
As the colours of the wires in the mains
lead of this appliance may not corre-
spond with the coloured markings ident-
ifying the terminals in your plug, pro-
ceed as follows:
The wire which is coloured green and
yellow must be connected to the termi-
nal in the plug which is marked with the
letter E or by the earth symbol
z or
coloured green or green and yellow.
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
The wire which is coloured brown must
be connected to the terminal which is
marked with the letter L or coloured red
(UK), or marked with the letter A for
(AUSTRALIA).
WARNING
THIS APPLIANCE MUST
BE EARTHED
Electrical connection
63
Non rewireable plugs BS 1363
If this machine or appliance is fitted
with a non-rewireable plug, the follow-
ing information applies:
If the socket outlets are not suitable for
the plug supplied with this product, it
must be cut off and an appropriate
plug fitted.
The plug cut from the flexible cord
should be disposed of and on no ac-
count be inserted into a socket else-
where in the house (electric shock ha-
zard).
The fuse cover must be refitted when
changing the fuse, and if the fuse
cover is lost, the plug must not be used
until a suitable replacement is ob-
tained. The colour of the correct re-
placement cover is that of the coloured
insert in the base of the plug, or the col-
our that is embossed in words in the
base of the plug (as applicable to the
design of plug fitted).
The correct fuse rating of the replace-
ment fuses that are ASTA approved to
BS 1362 should be fitted. Replace-
ment fuse covers may be purchased
from your local electrical suppliers, or
Miele Service Agent.
(The German standard version is sup-
plied with a cable and moulded plug
for connection to a 230 V single phase
supply. It must only be connected via
a fused 16 A socket).
Electrical connection
64
Plumbing
Connection to the water inlet
Water in the dishwasher must not
be used as drinking water.
The dishwasher may be connected to
a cold or hot water supply, max. 60°C.
Connection to a hot water supply
would save energy costs and time.
When connected to a hot water sup-
ply all programme stages which
would otherwise be carried out with
cold water (pre-wash and interim
rinse) as well as the COLD PRE-
WASH will be carried out with hot
water.
The inlet hose is approx. 1.5 m long;
a longer hose (4 m) may be bought
from the Miele Spare Parts Dept.
A stopcock with a 3/4" male thread
must be provided on site.
The dishwasher is constructed to
comply with DVGW regulations, and
may be connected to a suitable sup-
ply without an extra non-return valve
provided that national regulations
allow this.
The water pressure (flow rate at the
take-off point) must be between 1.0
and 10 bar pressure.
If the water pressure is too low the
water intake time must be increased
(see chapter Checking the water
level).
If the water pressure is too high, a
pressure reducer valve must be fitted.
The water inlet hose must not be
shortened or damaged in any way
(see illustration).
Connect the inlet hose with the Water-
proof-System preferably vertically
(use an angle connector if necessary).
If this is not possible, it can be in-
stalled horizontally, but it is essen-
tial that the main body of the Water-
proof valve box is above the hose
exit (see illustration). The lightning
power symbol should be above the
water flow arrow.
Plumbing
65
There must be a distance of at
least 20 cm between the floor and
the bottom of the Waterproof unit
housing, for either vertical or hori-
zontal installation.
If the stopcock is situated in the
worktop, a special angle connector
can be ordered from the Miele Spare
Parts Dept. (Part No. 2078910).
Lay the hose in such a way that it
does not rise above the bottom of
the Waterproof unit casing (see il-
lustration).
Plumbing
66
Drainage
The machine drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the machine via the drain
hose.
The dishwasher is supplied with ap-
prox. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
The drain hose can be extended
using a connection piece and an
extra drain hose, (up to max. 4
metres).
If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied.
The connection socket on the dish-
washer can be turned. The hose can
thus be laid to the right or left without
needing to loosen the hose clip.
The drain system must not exceed
4 metres. The drain pump has a
maximum delivery head of 1 metre.
The drain hose must not be short-
ened.
Venting the drainage system
Open the dishwasher door fully.
If the site drain connection is situated
lower than the guide path for the bot-
tom basket rollers in the open door the
drainage system must be vented.
Otherwise a siphoning effect during a
programme can cause the machine to
empty itself of water.
To vent:
Cut off the top of the vent valve in
the wash cabinet.
Plumbing
67
68
Technical Data
Height Freestanding 85 cm (adjustable + 1.0 cm)
Height U- and i-models 82 cm (adjustable + 5.0 cm)
Width 59.8 cm
Width of building in recess 60 cm
Depth 60 cm (Freestanding model)
57 cm (U- and i-models)
Depth with door open 118.5 cm (Freestanding model)
115.5 cm (U- and i-models)
Voltage
Rated load see data plate
Fuse rating
}
Test marks VDE, Radio and Television suppressed
Water pressure (flow rate) 1.0 - 10 bar pressure
Hot water connection max. 60 °C
Delivery head max. 1 m
Drainage length max. 4 m
Connection cable approx. 1.7 m
Capacity 12 place settings
Technical Data
69
70
71
Alteration rights reserved (G665/G667/G668) /000 2597
This paper consists of cellulose which has been bleached without the use of chlorine.
64


Need help? Post your question in this forum.

Forumrules
1

Forum

miele-g665
  • I have a Miele G 665 dishwasher. When I open the door water drips from the vent in the door. Can you please advise how to rectify this.
    Thanks
    Bill Submitted on 13-5-2020 at 01:03

    Reply Report abuse
    • Same problem here (Miele G665SC)... help welcome.

      Thanks
      Pedro Answered on 31-5-2020 at 23:06

      Vote up Report abuse
    • The tiny drain hose inside the door vent is not draining back to the sump.Take the door apart and you'll probably see it is blocked with goo. Use a pipe cleaner and/or beach to clean it out, reinsrall, and it will probably be ok again ... for a few months! Answered on 10-12-2021 at 18:23

      Vote up Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Miele G665 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Miele G665 in the language / languages: English as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Miele G665

Miele G665 User Manual - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info