543255
14
Zoom out
Zoom in
Previous page
1/54
Next page


  
The radio doesn’t switch on
The battery pack is discharged and/or has not been
installed correctly.
Verify that the battery pack is charged and that it has
been correctly installed.
The radio switches off shortly after it has
been switched on
Discharged battery pack. Recharge the battery pack.
The battery pack does not recharge
The battery-charger has not been connected or installed
correctly.
Inspect the connections of the battery-charger and the
installation of the batteries.
The radio switches on but is unable to
receive signals
The site of installation is too shielded. Move to an another area.
The volume is too low Adjust the volume level.
Incorrect CTCSS or DCS
Check that the CTCSS tone or DCS code corresponds
to the one set by the parties you are communicating
with.
Noise is always present in reception mode The Monitor function is enabled. Disable the Monitor function.
It is not possible to communicate with
other parties
An incorrect radio channel has been selected.
Select the same radio channel used by the parties you
are communicating with.
The radio is installed in a shielded area or is too far from
the party you are communicating with
Move to another area.
Incorrect CTCSS or DCS
Check that the CTCSS tone or DCS code corresponds
to the one set by the parties you are communicating
with.
Reception is fragmented and/or disturbed
The signal is very weak.
Try temporarily disabling the Squelch by means of the
Monitor feature.
The transmission distance is excessive and/or there are
obstacles in the transmission path
Move closer to the party you are communicating with or
to another area.
Other parties are using the same channel
Check the trafc on the radio channel by means of the
Monitorfeature and select another channel if required.
The radio has been installed too close to equipment that
causes interference (televisions, computers, etc.)
Increase the distance between the radio and this
equipment.
Transmission is not always possible
The channel is used by an excessive number of parties
or the transmission has been barred due to a busy
channel.
Select another channel. Ask the radio link provider to
disable the block due to busy channel.
VOX causes the radio to accidentally
enable transmission
The sensitivity and/or environmental
noise is too high.
Reduce the VOX sensitivity.
The VOX feature requires speaking in a
loud voice
The sensitivity is too low.
If the environmental noise is not high, increase the
sensitivity or use an optional microphone.
The autonomy of the battery pack is limited Commission time is too high.
Try reducing the transmission time and/or using a low
power.
Logic related faults (unreadable displayed
symbols, functions blocked, etc.)
Incorrect setting caused by a problem with the power
supply.
Recharge the battery pack
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland G11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland G11 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info