Manual Midland BTX2 PRO 2020 (page 14 of 52) (English, German, Dutch, French, Italian, Spanish)

738681

Zoom out

Zoom in

1/52

8 www.midlandeurope.com www.midlandeurope.com 9

Activate Conference mode

In “Intercom Mode” and no active audio, keep pressed the FWD and Middle buttons

for 3 sec. The voice announcement “Conference” will tell you that it is active.

When the Conference mode is active the “Phone” mode is not available because all the

devices paired on Vol+ and Vol – are temporary disconnected to guarantee the stability

of the conference mode.

Disable the “conference” mode

The conference mode can be disabled in every moment, just pressing the FWD and

Middle buttons for 3 sec. You will hear the voice announcement “Intercom” and from

that moment your Midland BTX2 PRO will start working with “one to one” intercom

and all the devices paired on Vol+ and Vol- are back, together with the “Phone” mode

and the “Talk2All-Universal intercom” feature.

Attention: when the “conference” mode is active, the “Talk2All- Universal Intercom” (to talk

with not Midland brand intercom) is not available.

Also if one unit was paired on the CTRL (middle) button, it is temporary unavailable,

you need to disable the “Conference” mode and go back to the standard “one to one”

Intercom mode.

How to use the conference mode

When the conference mode is active, is possible to open the intercom communication

pressing both the FWD and BWD button. One click on the button will open the inter-

com communication, one click on the same button will close it.

The two units that are in the middle of the chain (unit 2 and 3) must keep the intercom

open on both FWD and BWD button to allow the full communication of the four units

together.

“One Click Talk” function

When the conference mode is active, it is possible to open the intercom communica-

tion to all the 4 users just in “one click”. Press short the CTRL (middle) button and you

will automatically open the conference to all the unit connected.

Talk 2 All - Universal Intercom with dierent brand unit.

Thanks to the “Talk2 All - Universal Intercom” feature it is now possible to pair your

Midland BTX2 PRO to a dierent brand intercom available on the market.

You can pair a not Midland Intercom on the “Forward” button.

› On the Midland BTX2 PRO enter the setup mode: (with the unit OFF press and

hold down the Middle button about 7 sec. until the Red light is on permanently).

› Keep pressed the “Forward” button for 7 seconds: the Red and Blu LED light will

start ﬂashing fast, then (while you still keep the button pressed) the Red and Blu

LED lights will change to slow ﬂashing. Now you can stop pressing the button.

Talk2All - Universal Intercom

Not Midland Unit

On the other intercom (not Midland brand) follow the procedure to pair to a phone,

because the BTX2 PRO is paired as a Phone. If successfully paired the red/blue light

will stop ﬂashing and the blu light will slowly ﬂash instead.

Attention: remember to switch OFF all the other Bluetooth devices during the pairing pro-

cedure, only the two devices involved in the pairing must be turned on.

To open/close the “Universal Intercom” communication on the Midland

BTX2 PRO press very long (7 sec) in “Intercom” mode the Forward but-

ton. On the other intercom just press the phone redial or voice dial button.

Maybe it will be necessary to press the redial button two times, depending on the model

of the not Midland intercom.

Attention: In order to use the the “Talk2All-Universal Intercom” feature the pairing on the

other unit must be done as a phone. The other intercom (not Midland brand) will be able to

be paired to a phone only if two phones are supported.

You can pair also a Midland unit as Talk2All, that means the pairing must be done as a

phone (one unit use the Talk2All procedure and the other unit use the pairing to “Phone”

procedure).

Compatibility with Midland BT line units

The BTX2 PRO is compatible with BTX1 PRO, BTNext PRO, BT Next Conference,

BTX2 FM and BTX2 FM.

When paired the max distance of the intercom is deﬁned from the lower possible.

The BTX2 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and

BTX2) only if updated to ﬁrmware version 2014 or later.

Pairing the Midland BTX2 PRO to Bluetooth devices

The Midland BTX2 PRO unit can be paired to other Bluetooth devices, like Pho-

ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).

The pairing procedure must be done using the “Volume +” or the “Volume -“ buttons.

› Pairing to the “Volume +” button: for Phone with music A2DP stereo, GPS Naviga-

tor with A2DP audio or external mono/Stereo A2DP dongle.

› All devices paired to “Volume +” button have higher priority and will interrupt all the

other communications (like Intercom, FM Radio and Music).

› Pairing to the “Volume -” button: for a second phone with mono audio (Hands Free

Protocol) for GPS navigators/ Radar detector and other devices with mono audio.

MONO

›Phone (HFP Mono)

›GPS mono

›PMR446 Transceiver

MONO and STEREO

›Phone (HFP/A2DP Stereo)

›GPS (HFP/A2DP Stereo)

›Dongle (HFP/A2DP Stereo)

When a device is paired to the “Vol +” or “Vol –“ buttons the “Phone” mode is acti-

vated.

Attention: A2DP audio source are supported only on Vol+. The second phone paired on

Vol- can support only mono audio (HFP).

Background feature

It is possible to keep always in background the audio connection of the device paired

on “Vol-” button. In this way the Intercom communication will not be interrupted, for

example, by the GPS’s street indication or or other audio mono device. To activate the

“Background” feature just press long the “Vol-” button, the voice “Background ON”

will tell you that now is active.

To deactivate the “Background” feature just press again long the “Vol-” button, the

voice “Background disable” will tell you that now is not active anymore.

By default the “Background” feature is o.

Pairing with one or two phones

The cellular phone can be paired to the “Vol +” (if the support for stereo A2DP is

requested) or to the “Vol –“.

When a phone is paired to the “Vol +” or “Vol-“ the “Phone” mode is activated.

An incoming call has always the higher priority, that means all other communications

will be closed (Intercom, FM Radio, Music).

If another incoming call will arrive on the second phone, an alert sound will notify it.

How to pair the Midland BTX2 PRO to a Phone

To pair the Midland BTX2 PRO to a Phone, you must ﬁrst enter the setup mode:

1. Turn o the unit

2. Press and hold down the middle button about 7 sec., until the Red light is on per-

manently.

3. Now press for 3 seconds the “Volume +” or “Volume -” button, the Blue and Red

light will ﬂash.

4. Enable the Bluetooth device search feature on your mobile phone

5. After some seconds, “Midland BTX2 PRO” will be displayed on your mobile phone.

Follow the pairing procedure of your Phone. If a pin code is requested you must

enter “0000” (four time zero).

When successfully paired, the Blue light of the unit will be on for one second and then

the unit will exit the setup mode and switch to the working mode (the Blue light will

start ﬂashing).

You can use now your Midland BTX2 PRO together with the Phone.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Midland BTX2 PRO 2020 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Midland BTX2 PRO 2020 Manual

Product: