543246

Midland BTX1 FM Manual

22
Zoom out
Zoom in
Previous page
1/28
Next page
UK
Midland BTX1 FM - 21
› Follow the same procedure up described; now the blue LED will ash once.
› To exit the “Setup” mode, double click the “Middle” button.
How to pair PMR446 transceiver with integrated Bluetooth
If your PMR446 trasceiver has an integrated Bluetooth (like the G8BT), you must pair
the trasceiver using the “Volume +“ button:
› Turn o the unit
› Press and hold down the “Middle” button about 7 sec., until the Red light is on
permanently.
› Now press rmly (3 sec) the “Volume +” button, the Blue and Red light will ash.
› Follow now the pairing procedure explained on the manual of the transceiver
itself
Attention: If you are pairing to a G8BT transceiver, just when the BTX1 FM nish the
pairing (only the Blu LED is ashing) you must follow this procedure to activate the
Bluetooth connection:
› Shortly press to the “forward” button in “Phone” mode, a purple light will con-
rm the audio connection ON. Now it’s ready to transmitt and receive trough
the BTX1 FM
› Follow the same procedure every time you need to reconnect the G8BT to the
BTX1 FM (no need to make the pairing procedure again)
Attention: the PMR446 audio connection can be set on “Stand by” pushing the
“forward” button on the BTX1 FM in “Phone” Mode
Attention: the connection with the Bluetooth radio (G8E-BT) can be set in “Stand
by” mode simply by pushing the “forward” button on the BTX1 FM in “Phone” Mode.
How to use the wired audio input
Your Midland BTX1 FM is also supplied with a wired audio input (AUX), that can
be used to connect an audio source, like an iPod (or any other MP3 Player) or a
PMR446 transceiver for group communication or for a coverage increase.
Listening to music
To listen to music from the wired input, connect the audio source using the op-
tional AUX cable.
The volume buttons (Vol + and Vol -) cannot be used to adjust the volume of the
wired audio source. The AGC system with automatically increase the volume on
higher speed.
Attention: never set the volume of the MP3 Player to the maximum possible. Nor-
mally the best level is about the 70% of the maximum.
Hint: We recommend that you perform a few tests adjusting the volume of your
iPod/MP3 player so at the normal speed the Headset volume is suited to your
needs. The AGC system will automatically increase the volume on higher speed.
Make a note to remember this setting for future trips.
Enabling/disabling the wired input
If needed the wired input can be enabled or disabled:
Enabling/Disabling: Make a Long press on the “Backward” button (you will hear
one audio beep tone for enabling conrmation and two audio beep tone for di-
sabling).
Using a PMR446 transceiver with the cable connection
In order to connect the transceiver to your Midland BTX1 FM, you need to purcha-
se the specic 2.5mm plug AUX cable, sold separately.
ome manufacturers radios use a dierent pin conguration, so we recommend
that you ask your dealer as to which cable is best suited to your needs.
The cable connected to the transceiver normally has also a PTT button that can
be placed on the handlebar of your bike or held in your hand (If you are the pas-
sanger rider).
To communicate via the attached radio, press the PTT button to speak and release
it to listen. It is not possible to talk and listen simultaneously.
Adjust the volume of the transceiver to your needs, remembering that the volume
adjustment is controlled by the automatic AGC system and that it will therefore
be automatically increased in relation to background noise.
If you wish to use a PMR446 transceiver for group communications and simulta-
neously maintain the Intercom feature enabled between two or more BTX1 FM
devices, you must remember that every time you talk to communicate with the
PMR 446 transceiver (pressing the PTT button), you will also activate the intercom
of the BTX1 FM to the unit connected to the “Middle” button (thanks to the VOX
feature).
To avoid the Intercom activation when you speak on the PMR446, you can decide
to pair the BTX1 FM unit on the “Backward” or “Forward” (where the VOX is not
active) or if you still want to use the “Middle” button, you must disable the VOX
feature, as explained in the previous section.
Attention! If you disable the VOX feature, you will only be able to answer incoming
phone calls by pressing the “Forward” button.
Setup and special configurations
Resetting all paired devices
Sometimes you may nd it necessary to delete all the pairing references stored in
the BTX1 FM unit (reset operation).
To perform this operation you must rst enter the setup mode:
› Turn o the unit
› Press and hold down the “Middle” button about 7 sec., until the Red light is
on permanently.
› Than simultaneously press and hold down the “Volume +” and “Volume –“
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland BTX1 FM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland BTX1 FM in the language / languages: English, Italian as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info