Manual Midland bt2 intercom (page 9 of 23) (English)

232783

Zoom out

Zoom in

1/23

English

Attention: the device search procedure (red and blue

lights ﬂashing) continues for approximately 2 minutes.

If no device is found within this interval of time, the BT2

returns to the Setup mode (red light permanently on).

To start again the search, repeat the pairing procedure

from step 2. To cancel the pairing procedure (red and

blue indicators ﬂashing) and return to the Setup mode

at any time, press “Intercom” button twice.

Resetting all paired devices

Sometimes you may ﬁnd it necessary to delete all the pairing

references stored in the BT2 unit (reset operation).

To perform this operation, simultaneously press and hold

down the “Volume +” and “Volume –“ buttons for 4 seconds.

The Blue Light will be lit on for 1 sec.

This procedure deletes all the paired Bluetooth devices sto

red in the memory and it is therefore possible to start a new

“clean” pairing session.

Exiting from the Setup mode

After you have paired the desired Bluetooth devices, you must

quit the “Setup” mode in order to be able to use your BT2.

Press and hold the Intercom button (center button) for 3 se

conds.

The red indicator switches off and the blue one starts to ﬂash.

You can now use your BT2.

Reconnecting the unit to bluetooth devices

After successfully pairing your devices, you can switch them

off and on without having the repeat the pairing procedure.

If a connection failure occurs between the two devices (for

example because one device is switched off or you are not

within the maximum range), it is not necessary to repeat the

pairing procedure.

Simply switch the device on again or move within the maxi

mum range. If the connection cannot be re-established auto

matically, select the device from the “devices menu” of your

Bluetooth device (for example mobile phone, MP3 player,

etc…) and re-enable the connection.

Adjusting the volume

Your Midland BT2 uses AGC technology, which automatically

adjusts the listening volume in relation to background noise.

However, it is also possible to manually adjust the volume by

means of the “Volume+” and “Volume -“buttons.

For example, you can manually adjust the maximum volume

in very noisy environments (for example when travelling at

high speeds), to allow the AGC automatic system to change

the volume and use the manually set volume as maximum set-

ting. This operation is useful because each type and standard

of helmet is inﬂuenced in different ways by wind and back

ground noise.

Using the features of the bluetooth

devices

Using the intercom feature

To use the Intercom feature, be sure both units are turned on

and correctly paired together.

If you have purchased a “single” version, follow the pairing

procedure described in section “Pairing the unit with another

BT2 unit” above.

Priority: Intercom communications always have a hi

gher priority, compared to other communications, with

the only exceptions being Telephone and GPS Sat-Nav.

Therefore, the Intercom feature automatically disables all

other communications.

The Intercom feature is disabled only when an incoming call or

voice communication is received from the GPS Sat-Nav, and

is automatically re-enabled as soon as these communications

end.

Attention: some cell phone release the line after a few

seconds, which means that the Intercom feature may not

be immediately available.

The Intercom feature can be enabled in two ways:

Manual activation:

› Press “Intercom” button, on one of the two units. Commu

nication is enabled and remains active until you press the

“Intercom” button again. You will hear 1 audio tone when

the Intercom feature is enabled and 2 audio tones when it

is disabled.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Midland bt2 intercom in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Midland bt2 intercom

Midland bt2 intercom User Manual - German, French, Italian, Spanish - 146 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Midland bt2 intercom Manual

Product: