738663

Midland Alan HP 406 Manual

43
Zoom out
Zoom in
Previous page
1/146
Next page
Advanced operations 15
7 Advanced operations
In this section we’ll describe some advanced operations which you can
do with your handheld transceiver.
7.1 Channel Scanning
If you have more than one channel programmed, your ALAN
HP106/HP406 can scan them; in other words it can repeatedly switch
through all the programmed channels cyclically and automatically stop
when a signal is detected on one of them. During the scanning, only the
channels belonging to a specific scanning list (defined by the set-up) are
monitored. If a valid signal is received during the scanning, the scanning
stops and the communication is audible through the speaker. When the
signal is over, the scanning automatically restarts.
If the CTCSS/DCS or the selective call have been previously program-
med, the device could be set-up to stop only if the received signals con-
tain the correct signaling.
7.1.a Enabling/disabling scanning
To enable the scanning:
1) Turn off the device
2) Turn on the device keeping the MON + FUNC button pressed. A high
beep (after the acoustic tone of power-on confirmation stated in the
paragraph 5.1) notifies that the scanning is activated, and the status
LED will slowly blink amber.
During scanning the channel selector knob becomes invalid.
If the Scan List is empty, an error tone will be heard when you try to
activate the scan and the radio will not start the Scan Mode.
Obviously, at least two channels must be entered in the Scan List for
the unit to be put in the SCAN Mode.
If the PTT button is pressed during the channel scanning, this one will
stop and the radio will transmit on the first vacant channel, then the
unit will automatically resume scanning.
To stop the scanning, repeat the above procedure from step 1. A low
beep is produced and the scanning will stop.
7.1.b Priority Channel
Depending on the transceiver’s programming, one of the scanning list
channels could have been assigned as Priority Channel. The scanning
will monitor the priority channel more frequently.
The programming could has been also set-up to allow you to decide,
from time to time, which is the channel to assign as priority. For informa-
tion please contact your dealer/radio network manager.
To assign a priority channel (if previously enabled by the programming):
1) Ensure that the scanning is not active.
2) Before starting the scan mode, select the desired channel using the
channel selector.
3) Start the channel scanning as described in paragraph 7.1.a. The
channel previously selected by the channel selector will be scanned
more frequently.
Once the scanning is started, if you wish to change the priority chan-
nel, you need to disable the scanning. Therefore it is not sufficient to
turn-off the device, rotate the channel selector, and switch it on again.
Depending on the programming, on the priority channel could also be
set the busy channel lock out function (BCLO) or other conditions (i.e.
English
ISTR106_int 26-09-2003 9:47 Pagina 15
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland Alan HP 406 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland Alan HP 406 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info