543209
11
Zoom out
Zoom in
Previous page
1/34
Next page
4 | Alan 199 Instruction Guide Alan 199 Instruction Guide | 5
Washers
Washers
Washers
Washers
Screws
Screws
Screws
Bracket
Nuts
Nuts
Screws and
washers
Mount in position with bolts, lock washers and nuts or self-threading
screws. You can install this transceiver in any location where 12,6 Vdc ±
10% power is available. It can be connected to negative ground system.
Just be sure you connect the RED wire to the (+) terminal and the BLACK
wire to the (-) terminal.
Connect the RED wire (with in- line fuse holder) to the accessory termi-
nal on the ignition switch of your vehicle. Make a good mechanical and
electrical connection to the frame of the vehicle for the black wire. You
can use an auto accessory lighter plug, available on the CB market, to
connect your Transceiver to the vehicles cigarette lighter receptacle. Ho-
wever, is better to connect the DC power cord directly to the accessory
terminal of the ignition switch. This will prevent unauthorized use of the
transceiver, and will also prevent you from leaving it on unintentionally.
Before operation, you must install and connect your antenna system. The
lead from the antenna you’ve installed should be connected to the an-
tenna coaxial connector. If you are using an external speaker, connect it
to the EXT-SPKR jack.
REPLACING FUSE
If you replace the fuse for DC Power Cord, use 2 A type (one supplied
as spare). Hold the fuse holder and press on the inside, then rotate the
holder.
CONNECTING THE MICROPHONE
Your transceiver has a new microphone connector. This ensures that you
won’t accidentally pull out or loosen the plug connection when moving
the microphone cable out.
INSTALLATION
Safety and convenience are the primary consideration for mounting any
piece of mobile equipment. All controls must be readily available to the
operator without interfering with the movements necessary for safe ope-
ration of the vehicle. Be sure all cables are clear of the brake, clutch and
accelerator. Also, thought must be given to the convenience and comfort
of passengers.
Another extremely important requirement is the ease of installation and
removal for those occasions when you might want to remove the unit for
service and maintenance.
The most common mounting position for a transceiver is under the da-
shboard directly over the drive shaft hump. Do not mount the transceiver
in the path of the heater or air conditioning air stream. Take your time
and plan your installation carefully. When you have determined the best
location for mounting, use the mounting bracket as a template to mark
mounting holes. Take care when you drill the holes that you do not drill
into wiring, trim or other accessories.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midland ALAN 199 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midland ALAN 199 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info