Manual Midea 36QMS5GP482EEP001 (page 4 of 16) (English)

684500

Zoom out

Zoom in

1/16

Gas installation must be made in accordance with AS5601;

Also refer to rangehood manufacturers recommendation.

Check gas presure, note the correct setting from the data

plate sealed inside the front appliance drawer *.

Stability bracket

WARNING: In order to prevent accidental tipping of the

appliance, for example a child climbing onto the open oven

door, the stabilising means must be installed.

Note: If the wall plug provided is not suitable for the wall

material please use an appropriate device to ensure secure

holding of the "screw" to the wall.

Installing the gas cooker:

(Flexible connection are NOT supplied with this appliance)

- An inlet manifold extension pipe must be fitted to the

appliance. Part supplied in the drawer of the appliance.

- Ensure that the pipe is connetted using the washer

provided and that the braket is screwed to the appliance

as shown in the diagram below.

- Fit the supplied pressure regulator (for Natural gas) using

the NG test piont adaptor and washer to the inlet manifold.

Ensure the arrow is pointing towards the appliance and

that pressure testpoint is accessible from the final

position.

- Push the cooker back and install the stabilizing chains.

- Connect the appliance inlet manifold to the consumer

piping outlet using only fixed piping. This final connection

is made when the product is pushed back into position by

access under the cooker.

The hose assembly

- must comply with AS/NZS 1869 Class B or D,

- be of appropriate internal diameter and be kept as short as

possible (less than 1,2 mm)

Fig. B Fig. C

GAS CONNECTION

- It must not be kinked

- It must not be in contact with hot surfaces.

IT IS RECOMMENDED THAT A SERVICE TAP AND UNION BE

FITTED ADJACENT TO THE APPLIANCE INLET TO

FACILITATE FUTURE SERVICING.

5 burner models: set the burner pressure to 1kPa for Natural

Gas and 2.75kPa for U-LPG with the wok burner operating a

full rate'. For commissioning of the appliance with the

regulator for Natural Gas, the test point pressure should be

1.00kPa with all burners operating on HIGH.

Apply a manometer to the test nipple and reset the regulator

if necessary. Do not forget to replace the test nipple screw

and to leave the instructions book with the user.

VERY IMPORTANT FOR THE INSTALLER

Do not attempt to turn or stress threaded elbow of the

manifold: you risk damage to this part of the gas appliance

which may void the manufacturers warranty.

Before Leaving – Check all connections for gas leaks.

DO NOT use a naked flame for detecting leaks. Ignite all

burners to ensure correct operation of gas valves, burners

and ignition. Turn gas taps to low flame position and

observe stability of the flame.

When satisfied with the cooker, please instruct the user on

the correct method of operation.

In case the appliance fails to operate correctly after all

checks have been carried out, refer to the authorised

service provider in your area.

GAS CONVERSION AND ADJUSTMENT

When used with natural gas all burners have been preset at

our factory and further adjustment should not be

necessary. Conversion kits to other gases are available

from the place of purchase. Do not attempt to fit the

conversion kit yourself. Conversion to U-LPG gas should

only be carried out by an authorized technician.

GAS ADJUSTEMENTS

- change the injectors

- adjust the minimum flow

‘When conver ting from Natural Gas to U-LPG ensure that

the NG regulator is removed and replaced with the Test

Point Assembly. A gas regulator suitable for a supply

pressure of 2.75kPa should be part of the gas tank supply

and should be adjusted with the wok burner operating at

maximum.

REPLACEMENT OF THE INJECTORS

When required to operate on other gas replace the

injectors in accordance with information referred to in chart

below.

A test point fitting must be

installed between the piping and

the appliance for the pressure to

be checked to ensure it is

operating for ULPG at 2.75 kPa.

Be aware that the appliance has

two gas inlets (L/R). Before

performing the leakage test

select which side will be the

connection point and cap and

pressure test the side that will not

be used.

A test point fitting must be

installed between the piping and

the appliance for the pressure to

be checked to ensure it is

operating for NATURAL GAS at 1

kPa.

Be aware that the appliance has

two gas inlets (L/R). Before

performing the leakage test select

which side will be the connection

point and cap and pressure test

the side that will not be used.

Pressure regulator for natural

gas

Pressure tst point for ULPG

Wall Fixing

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Midea 36QMS5GP482EEP001 in the language / languages: English as an attachment in your email.

The manual is 8,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Midea 36QMS5GP482EEP001 Manual

Product: