658461
8
Zoom out
Zoom in
Previous page
1/61
Next page
8 M32 DIGITAL CONSOLE User Manual
Main
(6) SEL Button
Press to select the Main bus for editing.
(7) COMP
The COMP indicator will illuminate when compression is being applied to
the stereo output mix.
(9) CLR SOLO Button
Press to clear all sources assigned to the solo bus.
(10) SOLO Button
Press to solo the main bus.
(11) Scribble Strip
Customisable information relating to the main bus are displayed here.
(12) MUTE Button
Press to mute the main bus.
(5) Fader
Use the MIDAS PRO Fader to adjust the output of the main bus.
(12) MUTE Button
Press to mute the main bus.
(5) Fader
Use the MIDAS PRO Fader to adjust the output of the main bus.
1.3 Cong/Preamp
(1) GAIN Rotary Control
On a microphone preamplier, input gain varies the amount of amplication
applied to the microphone. Adjust the preamp gain for the selected channel
with the GAIN rotary control.
(2) LED Display
The LED display in the Cong/Preamp section illustrates the signal input
level for the selected channel. This is shown as a value between 0 dB and
-30dB. When there is a signal present, but below -30 dB, the SIG LED is lit.
When the signal exceeds 0 dB the CLIP LED illuminates.
Please note that, when pressing the VIEW button, the signal input level
displayed on the Main Display shows a value of between 0 dB and -60 dB.
(3) FREQUENCY Rotary Control
The FREQUENCY rotary control selects the frequency at which the low
cut lter begins to lter unwanted frequencies for the selected channel.
Thelter is engaged by pressing the LOW CUT button (see below).
Please note that the low cut lter is only available for the 32 primary
inputchannels.
(4) 48 V
Phantom power is a method for transmitting DC electric power through
microphone cables to operate microphones that contain active electronic
circuitry. It is most commonly used with condenser microphones,
thoughmany active direct boxes also use it. The technique is also used in
other applications where power supply and signal communication take place
over the same wires. Press the 48 V button to apply phantom power on the
selected channel’s physical input.
(5) Ø
An audio signals ‘phase’ refers to its position in a point of time along the
waveform cycle, with each cycle being 360°. Press the Ø button to reverse
the selected channel’s phase by 180°. This can be useful when using the
reverse phase function to cancel noise across more than one channel.
(6) LOW CUT
Press the LOW CUT button to engage the low cut lter for the
selectedchannel.
Please note that the low cut lter is only available for the 32 primary
inputchannels.
(7) VIEW
Press the VIEW button to access more detailed parameters on the
MainDisplay. See the section Main Display - cong for more details.
1.4 Gate
(1) THRESHOLD Rotary Control
A noise gate is a device that is used to control the volume of an audio
signal. Often used in conjunction with a compressor (see DYNAMICS),
whichattenuate signals above a certain threshold, noise gates attenuate
signals that register below the threshold. By turning the THRESHOLD
rotary control, the audio level at which the gate aects the signal can
becontrolled.
(2) LED Display
The LED display illustrates when the Gate is functioning for the selected
channel by illuminating the red GATE LED at the bottom of the display.
(3) GATE
Pressing the GATE button engages the noise gate for the selected channel.
(4) VIEW
Press the VIEW button to access more detailed parameters on the
MainDisplay. See the section Main Display - gate for more details.
(1) (2) (3)
(4) (5) (6)
(7)
(1)
(2)
(3)
(4)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas M32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas M32 in the language / languages: English as an attachment in your email.

The manual is 9,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info