658461

Midas M32 Manual

4
Zoom out
Zoom in
Previous page
1/61
Next page
4 M32 DIGITAL CONSOLE User Manual
Precautions
Before installing, setting up or operating this equipment make sure you have read and fully understand all of this section and the
‘IMPORTANTSAFETY INSTRUCTIONS’ at the front of this manual.
This equipment is supplied by a mains voltage that can cause electric shockinjury!
The following must be observed in order to maintain safety and electromagnetic compatibility (EMC) performance.
Safety warnings
Signal 0V is connected internally to the chassis.
To completely isolate this equipment from the AC mains, while observing full
safety precautions (see ‘Power’ on page xiii), switch o the isolator switch
(abovethe mains power sockets on rear of control centre) and then switch o
the mains at the three mains outlets. Unplug the three mains leads from the
rear of the control centre. For details of how to remove Volex locking type plug,
see‘Power’ below.
To avoid electrical shock do not remove covers.
General precautions
In the event of ground loop problems, disconnect the signal screen at one end of
the connecting cables. Note that this can only be done when the equipment is
used within a balanced system.
Do not remove, hide or deface any warnings or cautions.
Power
The system power supplies contain LETHAL VOLTAGES greatly in excess of the
mains voltage and its rails can produce extremely large currents that could burn
out equipment and wiring if shorted.
The internal power supplies are of the switch mode type that automatically sense
the incoming mains voltage and will work where the nominal voltage is in the
range 100 VAC to 240 VAC.
Each mains inlet is to be sourced from its own separate wall-mounted mains
outlet socket.
Otherwise, their mains sources must be suitably distributed so as to meet local
safety regulations.
A Volex locking type plug is tted on each supplied mains cable, which plugs into
a mains IEC connector on the unit. When tted properly the Volex plug locks into
place, preventing it from working loose, or being inadvertently knocked loose or
pulled out. To t a Volex plug, insert it into the mains IEC connector and push it in
until it locks in place. Then, check to make sure it is locked in place. To remove it,
release its locking device and then pull it out. When tting or removing a Volex
plug, always hold the plug itself and never use the cable, as this may damage it.
During operation, a minimum of two of its three mains inlets must be connected
and supplying power.
When removing the equipment’s electric plugs from the outlets, always hold the
plug itself and not the cable. Pulling out the plug by the cable can damage it.
Never insert or remove an electric plug with wet hands.
Do not connect/disconnect a mains power connector to/from the M32 Control
Centre while power is being applied to it. Switch the power o rst.
Before switching the M32 Control Centre on or o, make sure that all monitor
loudspeaker power ampliers are turned o or muted.
Handling the equipment
Completely isolate the equipment electrically and disconnect all cables from the
equipment before moving it.
When lifting or moving the equipment, always take its size and weight into
consideration. Use suitable lifting equipment or transporting gear, or sucient
additional personnel.
Do not insert your ngers or hands in any gaps or openings on the equipment,
forexample, vents.
Do not press or rub on the sensitive surface of the GUI screens.
If the glass of the GUI screen is broken, liquid crystals shouldn’t leak through the
break due to the surface tension of the thin layer and the type of construction of
the LCD panel. However, in the unlikely event that you do make contact with this
substance, wash it out with soap.
Installation
Before installing the equipment:
Make sure the equipment is correctly connected to the protective earth
conductor of the mains voltage supply of the system installation through the
mains leads
Power to the equipment must be via a fused spur(s)
Power plugs must be inserted in socket outlets provided with protective earth
contacts. The electrical supply at the socket outlets must provide appropriate
over-current protection
Both the mains supply and the quality of earthing must be adequate for
theequipment
Before connecting up the equipment, check that the mains power supply voltage
rating corresponds with the local mains power supply. The rating of the mains
power supply voltage is printed on the equipment.
Location
Ideally a cool area is preferred, away from power distribution equipment or other
potential sources of interference.
Do not install the equipment in places of poor ventilation.
Do not install this equipment in a location subjected to excessive heat, dust or
mechanical vibration. Allow for adequate ventilation around the equipment,
making sure that its fans and vents are not obstructed. Whenever possible,
keepthe equipment out of direct sunlight.
Do not place the equipment in an unstable condition where it might accidentally
fall over.
Make sure that the mains voltage and fuse rating information of the equipment
will be visible after installation.
Ensure that all underside vents are left clear during operation.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas M32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas M32 in the language / languages: English as an attachment in your email.

The manual is 9,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info