658492
59
Zoom out
Zoom in
Previous page
1/64
Next page
Powering the XL8 system 45
DL461 Router
Operator Manual
Powering the XL8 system
The following details the recommended power up and power down procedures for the
XL8 system.
>> To power up the XL8 system
Important Note:
DO NOT switch on the speaker sub-system until after the start-up of the XL8
system has been completed.
After all XL8 system interconnections have been made (see Chapter 30 “Panel
Connections”), start up the XL8 system:
1 Make sure that all of the XL8 system equipment is switched off, that is, the XL8
Control Centre, speaker sub-system, DL431 mic splitters, DL451 modular line I/O
units, DL461 routers and DL471 DSP units.
2 Switch on the XL8 Control Centre (see “To switch on the XL8 Control Centre” on
page 46).
3 On the XL8 Control Centre, move all of the monitor and master channel faders to
the minimum position and mute all of the master channels. The master channels
can be found in the mix and output fast zones (see “XL8 control surface” on
page 7).
4 Switch on the DL431 Mic Splitters.
5 Switch on the DL451 Modular I/O units.
6 Switch on the DL471 DSP units.
7 Switch on the DL461 Routers.
8 After the status LEDs (top of each GUI screen on the XL8 Control Centre) turn
green, switch on the speaker sub-system.
9 Switch on the audio source and start playing the audio.
10 On the XL8 Control Centre, check that the audio inputs are routed to the master
channels. Then, unmute the master channels and gradually increase their faders,
while listening to the sound levels from the speakers.
If there are no sounds at all from the speakers when the faders are at maximum, move
the faders to below the 0dB level and check if the audio is muted somewhere along the
input paths and also check that the individual speakers are switched on. If there is still
no sound from the speakers, contact Midas Technical Support.
>> To power down the XL8 system
Important Note:
BEFORE switching off any of the XL8 system components, make sure to mute
the audio from the speakers and switch off the speaker sub-system.
1 Mute the audio from the speakers and switch off the speaker sub-system.
2 Switch off the DL431 Mic Splitters.
3 Switch off the DL451 Modular I/O units.
4 Switch off the DL471 DSP units.
5 Switch off the DL461 Routers.
6 Switch off the XL8 Control Centre (see “To switch off the XL8 Control Centre” on
page 47).
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas DL461 Router at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas DL461 Router in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info