658492
25
Zoom out
Zoom in
Previous page
1/64
Next page
11
DL461 Router
Operator Manual
Chapter 4: Getting Started
This chapter shows you how to connect up, switch on, set up and configure the DL461
Router.
Note: The DL461 Router is operated from the XL8 Control Centre only. For more
information, see the XL8 Live Performance System Owner’s Manual (part number
DOC02-XL8).
Connecting up (XL8 system)
There are two DL461 Routers, X and Y, in the standard XL8 system configuration. As
the routers form the hub of the XL8 Live Performance System, system set-up involves
connecting up both DL461 Routers with the DL471 DSPs, DL431 Mic Splitters, DL451
Modular I/Os and the XL8 Control Centre.
>> To connect up the X router
Refer to Figure 1 on page 12.
1 In AES50 audio - bank 0, connect the 10 sockets to the X AES50 audio socket
on the 10 DSP units.
2 In AES50 audio - bank 1, connect socket 1 to the X AES50 audio socket (A or
B, depending on mic amp selection) on Mic splitter 1. Similarly, connect sockets
2, 3 and 4 in this bank to the other three mic splitters.
3 In AES50 audio - bank 1, connect socket 5 to the X AES50 audio socket on the
I/O unit.
4 In the Ethernet control bank of connectors, connect the 10 sockets to the X
Ethernet control socket on the 10 DSP units.
5 Connect the AES50 synchronisation (word clock or AES3 sync), if required (see
“Rear panel connections” on page 8).
6 Connect the snake (optical or CAT6e) to rear of control centre (see “Rear panel
connections” on page 8).
7 Mains power supply - insert the IEC connector of the mains cable into the rear
of the unit and then plug it into the mains power outlet.
The connection configuration for AES50 audio banks 0 and 1 has been derived for
optimum accessibility and convenience. However, these connections are flexible,
so you can swap the bank connections over or reallocate the mic splitter and I/O
connections within their respective bank, if you want.
>> To connect up the Y router
Follow the procedure for connecting the X router, but use the Y connections where
available.
>> To connect the X and Y routers together
In the control expansion section (rear panel) of the X router, connect the router/
router interconnection cable to the Ethernet socket. Then, connect the other end of
the cable to the equivalent socket on the Y router.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Midas DL461 Router at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Midas DL461 Router in the language / languages: English as an attachment in your email.

The manual is 6,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info