773555
7
Zoom out
Zoom in
Previous page
1/75
Next page
5
OXY 210 EN
8. Display Mode
When the device is switched on, shortly press the ON/OFF
button 1 to switch to another display mode to select your
desired display mode 9. There are 6 different display
modes. The default setting is mode 1.
9. Using the Lanyard
7
1. Thread the thinner end of the lanyard through the
hanging hole at the rear end of the device.
2. Thread the thicker end of the lanyard through the
threaded end before pulling it tightly.
10. Malfunctions and Actions to take
11. Cleaning and Disinfecting
Use an alcohol swab or cotton tissue moistened with
alcohol (70% Isopropyl) to clean the silicone that touches
the finger inside of the device. Also clean the finger being
tested using alcohol before and after each test. Allow the
device to dry thoroughly before use.
Never use abrasive cleaning agents, thinners or
benzene for cleaning and never immerse the
device in water or other cleaning liquids.
12. Guarantee
This device is covered by a 2 year guarantee from the date
of purchase. During this guarantee period, at our discre-
tion, Microlife will repair or replace the defective product
free of charge.
Opening or altering the device invalidates the guarantee.
The following items are excluded from the guarantee:
Transport costs and risks of transport.
Damage caused by incorrect application or non-
compliance with the instructions for use.
Damage caused by leaking batteries.
Damage caused by accident or misuse.
Packaging/storage material and instructions for use.
Regular checks and maintenance (calibration).
Descrip-
tion
Symptom/Possible
causes
Solutions
SpO2 or
pulse rate
do not
display
normally.
1. Finger is not
inserted
correctly.
2. Patient SpO2
value is too low to
be measured.
3. There is exces-
sive illumination.
1. Retry inserting the
finger.
2. & 3. Measure more
times. If you deter-
mine the product is
working correctly,
consult your doctor.
SpO2 or
pulse rate
is shown
unstable.
1. Finger might not
be inserted deep
enough.
2. Excessive patient
movement.
1. Retry inserting the
finger.
2. Sit calmly and retry.
The
device
cannot be
powered
on.
1. No batteries or
low battery
power.
2. Batteries are not
installed
correctly.
3. The device may
be damaged.
1. Replace the
batteries.
2. Remove and rein-
stall the batteries.
3. Contact your local
Microlife-Customer
Service.
The
display
suddenly
switches
off.
1. The device is
automatically
powered off,
when no signal
was detected
after 10±2
seconds.
2. The battery
power is too low
to operate.
1. Normal.
2. Replace the
batteries.
Descrip-
tion
Symptom/Possible
causes
Solutions
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Microlife OXY 210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Microlife OXY 210 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info